Array ( [0] => just-arrived [1] => 35-60-hp-granulators [2] => feed-paddle-roll-granulators [3] => just-arrived [4] => 35-60-hp-granulators [5] => feed-paddle-roll-granulators )
  • Stock#: 16922

    USED CUMBERLAND 1456 FEED ROLL GRANULATOR


    CUMBERLAND MODEL 1456 GRANULATOR, S/N 84000-87011, 14″ X 56″ FEED THROAT, 3 KNIFE OPEN ROTOR, 2 BED KNIFE, 50 HP 230/460 VOLT 1175 RPM MOTOR, CONVEYOR FEED HOPPER WITH REAR MOUNTED 5″ DIAMETER X 56″ WIDE STEEL KNURLED FEED ROLLS, FEED ROLLS HAVE PNEUMATIC PINCH AND ARE POWERED BY A 1.5 HP 208-230/460 VOLT 1140 RPM MOTOR THRU A 40:1 GEARBOX AND CHAIN & SPROCKET DRIVE SYSTEM, GEARBOX IS RATED FOR A MAXIMUM OF 1.85 HP AND HAS AN OUTPUT TORQUE OF 2080 LBS PER INCH, CHAMBER IS MOUNTED TO A LOW PROFILE PLATE BASE ON VIBRATION CONTROL PADS, 10″ OD AIRVEYOR DISCHARGE, INCLUDES PNEUMATIC AIR VALVE CONTROL SYSTEM FOR THE FEED ROLLS, OVERALL DIMENSIONS ARE 10′ X 80″ X 100″, APPROXIMATELY 10,000 LBS, STARTER AND CONTROLS FOR THE GRANULATOR ARE NOT INCLUDED

  • Array ( [0] => just-arrived [1] => 35-60-hp-granulators [2] => feed-paddle-roll-granulators [3] => just-arrived [4] => 35-60-hp-granulators [5] => feed-paddle-roll-granulators )
  • Stock#: 16836

    USED RAPID 500/120 FEED ROLL GRANULATOR


    RAPID MODEL 500-120 KURF GRANULATOR WITH FEED ROLLS, S/N RA 511.246815.20.1, 18″ X 48″ FEED THROAT, 5 KNIFE OPEN ROTOR, 3 BED KNIFE, TANGENTIAL CUTTING CHAMBER, 50 HP 460 VOLT MOTOR, 6″ LEFT HAND AIRVEYOR DISCHARGE, 8mm HOLES SCREENS INSTALLED, INSULATED HOPPER WITH REAR MOUNTED 1200mm WIDE KNURLED STEEL FEED ROLLS WITH DANCER BAR, FEED ROLLS HAVE PNEUMATIC PINCH, HOPPER HAS ELECTRIC POWER BACK JACK ASSIST, INCLUDES ORIGINAL OEM STARTER PANEL WITH ALLEN BRADLEY SOFT STARTER FOR THE GRANULATOR AND A VARIABLE SPEED DRIVE (8-45 METERS/MIN LINE SPEED) (26 – 147 FEET/MIN LINE SPEED) FOR THE FEED ROLLS, REMOTE KEYPAD CONTROL FOR THE FEED ROLLS MOUNTED ON STARTER DOOR, 2015 MODEL YEAR WITH LOW USE AND IS IN EXCELLENT RUNNING CONDITION

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 12669

    USED TRIA 120-49/TR-NS GRANULATOR W/FEED ROLLS


    TRIA MODEL 120-49/TR-NS GRANULATOR, S/N 33.9447.96, 17.75″ X 50.25″ FEED THROAT, 5 KNIFE OPEN ROTOR, WITH ADJUSTABLE KNIVES, 2 BED KNIFE WITH WATER COOLED BED KNIFE BLOCKS, 38″ WIDE STEEL FEED ROLL IN-FEED WITH DANCER BAR, 19.5″ X 9.5″ FRONT PARTS IN-FEED, 50 HP 480 VOLT MOTOR, FRAME BASE, 6″ LEFT HAND AIRVEYOR, MANUAL JACK SCREW CHAMBER OPENING, .065 KW FEED ROLL MOTOR INTO GEARBOX, INCLUDES STAND ALONE CONTROL PANEL

  • Array ( [0] => as-is-granulators-0-25-hp [1] => feed-paddle-roll-granulators [2] => as-is-granulators-0-25-hp [3] => feed-paddle-roll-granulators )
  • Stock#: 16536

    USED BALL & JEWEL 812 FEED ROLL GRANULATOR


    BALL & JEWEL MODEL 812 FEED ROLL GRANULATOR, NO S/N, 8″ X 12″ FEED THROAT, 3 KNIFE OPEN ROTOR, 2 BED KNIFE, 25 HP 460 VOLT ROTOR MOTOR, CHAIN AND SPROCKET DRIVEN FEED ROLLS, SPRING PINCH TOP ROLL IS AN 8″ DIAMETER X 12″ WIDE SMOOTH STEEL ROLL, LOWER ROLL IS A 6″ DIAMETER 12″ WIDE KNURLED STEEL ROLL, ROLLS ARE IN OFF-SET POSITION, ROLLS ARE POWERED BY A 3/4 HP 1725 RPM D/C MOTOR THROUGH A 19:1 GEARBOX WITH AN OUTPUT SPEED OF 91 RPM, BLOWER DISCHARGED VIA 5 HP 3480 RPM MOTOR WITH AN 4″ OD OUTLET, ALUMINUM BLOWER IMPELLER, MOUNTED ON CASTERS, COMPLETE WITH STARTER AND CONTROLS FOR GRANULATOR, D/C DRIVE FOR FEED ROLLS IS “CONSTANT” ON WITH NO VARIABLE SPEED CONTROL

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 16402

    USED AEC / NELMOR MV810 FEED ROLL GRANULATOR


    USED AEC/NELMOR MODEL MV810 FEED ROLL GRANULATOR, S/N 03C05415, 8″ X 10″ FEED THROAT, 3 KNIFE OPEN ROTOR, 2 BED KNIFE, 7.5 HP 230/460 VOLT ROTOR MOTOR, INSULATED REAR FEED HOPPER (CLOSED OFF), FRONT LOW MOUNTED FEED ROLL IN-FEED, 10.5″ WIDE X 2.5″ OD KNURLED STEEL FEED ROLLS ARE POWERED BY A 90 VOLT D/C 1750 RPM MOTOR THRU A WARNER UNI-MODULE MODEL EUM180-1040 CLUTCH BRAKE RATED UP TO 3600 RPM TO A BOSTON GEAR BOX, SPRING PINCH FEED ROLL TENSIONER, FEED ROLL MATERIAL OPENING IS 9.5″ WIDE, FEED ROLLS ARE CONTROLLED VIA BRONCO SECO B160 D/C VARIABLE SPEED CONTROLLER, HOPPER HAS MANUAL ACTION JACK CO TILT BACK ASSIST, RIGHT HAND 4″ OD VACUUM TAKE OFF DISCHARGE, ON CASTERS, COMPLETE WITH GRANULATOR STARTER AND CONTROLS, 2003 MODEL YEAR

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 16280

    USED NELMOR G1215P1 GRANULATOR WITH FEED ROLLS


    USED NELMOR MODEL G1215P1 GRANULATOR, S/N 99K03325, 12″ X 15″ FEED THROAT, 3 KNIFE OPEN ROTOR, 2 BED KNIFE, 15 HP 208-230/460 VOLT 1480 RPM MOTOR, DOUBLE WALL REAR TOP HAND FEED WITH FRONT MOUNTED KNURLED STEEL FEED ROLLS, PNEUMATIC PINCH ON ROLLS, FEED ROLLS POWERED BY APPROXIMATE 1/2 HP D/C MOTOR AND CONTROLLED BY A BRONCO SECO D/C VARIABLE SPEED CONTROL, HOPPER / FEED ROLL ASSEMBLY HAS HYDRAULIC JACK TILT BACK ASSIST, 4″ OD RIGHT HAND AIRVEYOR DISCHARGE, COMPLETE WITH STARTER AND CONTROLS FOR GRANULATOR AND FEED ROLLS

  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => feed-paddle-roll-granulators [3] => just-arrived [4] => 75-hp-granulators [5] => feed-paddle-roll-granulators )
  • Stock#: 16612

    USED HERBOLD SMS45/160-H5-2 FEED ROLL GRANULATOR


    HERBOLD MODEL SMS45/160H5-2 GRANULATOR, S/N 3696, 23.5″ X 61″ FEED THROAT, BELT DRIVEN 5 KNIFE OPEN ROTOR, 2 BED KNIFE, 100 HP 230/460 VOLT MOTOR, 6″ DIAMETER X 56″ AMBRITT CRUSHER FEED ROLL IN-FEED, S/N 255-003, POWERED BY A 3 HP A/C 1750 RPM 208-230/460 VOLT MOTOR THRU BOSTON GEAR 24:1 GEARBOX, CHAIN AND SPROCKET DRIVEN, MANUAL FEED ROLL ADJUSTMENT, IN ADDITION TO THE FEED ROLLS THERE IS A 11-3/4″ X 30″ PARTS CHUTE, GRANULATOR CHAMBER IS OPENED VIA 3 HP HYDRAULIC JACK BACK ASSIST, 1 HP MATERIAL AUGER DISCHARGE ASSIST WITH AN OK160 6″ OUTLET, INCLUDES TWO USED SETS OF 20 ROTOR AND 4 BED KNIVES, AND KNIFE ADJUSTING FIXTURE, STARTER AND CONTROLS FOR GRANULATOR AND FEED ROLLS ARE NOT INCLUDED, AVAILABLE WITH OR WITHOUT THE FEED ROLLS

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 12687

    FOREMOST HSFG-1116 GRANULATOR W/FEED ROLLS


    FOREMOST MODEL HSFG-1116 GRANULATOR, S/N 39617, 11″ X 16″ FEED THROAT, 6 KNIFE OPEN ROTOR, 2 BED KNIFE, ROTATING END DISKS, DESIGNED FOR FILM, TRAY AND FEED ROLL IN-FEED, MODEL NRF-9 3″ X 9″ STEEL GROOVED FEED ROLLS IN OFFSET POSITION FRONT MOUNTED, TRAY HOPPER ALSO HAS 8″ TOP BLOW IN-FEED, INSULATED CHAMBER BODY PANELS, 5 HP BLOWER BLOWER MACHINE MOUNTED WITH 5″OD OUTLET, 20 HP 460 VOLT GRINDER MOTOR, FEED ROLLS POWERED BY 1/2 HP 90 VOLT D/C MOTOR THRU GEARBOX, MOUNTED ON CASTERS, COMPLETE WITH STARTER AND CONTROLS FOR GRANULATOR, BLOWER, & D/C VS DRIVE FOR ROLLS

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 12939

    CUMBERLAND 284 GRANULATOR W/FEED ROLLS


    CUMBERLAND MODEL 284 GRANULATOR, S/N 325525-83061, 10″ X 12″ FEED THROAT, 3 KNIFE OPEN ROTOR, 2 BED KNIFE, APPROXIMATE 2.75″ DIAMETER X 8″ WIDE GROOVED, KNURLED, & INTERLOCKED STEEL FEED ROLLS, PNEUMATIC PINCHED IN OFFSET POSITION, POWERED BY A 1 HP D/C MOTOR WITH VARIABLE SPEED DRIVE, MOUNTED ON CASTERS, COMPLETE WITH STARTER AND CONTROLS

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 12690

    SPROUT 9 X 11 GRANULATOR W/FEED ROLLS


    SPROUT 9 X 11 FEED ROLL GRANULATOR, NO S/N, 9″ X 11.5″ FEED THROAT, 3 KNIFE OPEN ROTOR, 1 BED KNIFE, 20 HP 230/460 VOLT MOTOR, SIDE FEED TRAY FEED HOPPER WITH FRONT MOUNTED 3″ X 9″ STEEL KNURLED FEED ROLLS POWERED BY APPROXIMATE 1/3 HP 90 VOLT D/C MOTOR, 7″ OD AIRVEYOR DISCHARGE, MOUNTED ON FRAME BASE, COMPLETE WITH STARTER AND CONTROLS FOR GRANULATOR AND V/S DRIVE FOR THE FEED ROLLS

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => recycling [3] => used-equipment [4] => feed-paddle-roll-granulators [5] => recycling )
  • Stock#: 12541

    CUMBERLAND MODEL 18 x 37 GRANULATOR /W FEED ROLLS


    CUMBERLAND MODEL 18 x 37 GRANULATOR, S/N 50510-84013, 18″ X 37″ FEED THROAT, 5 KNIFE STEEP ANGLE STEP ADJUSTABLE ROTOR KNIVES (10 SEGMENTS), 2 BED KNIFE, DESIGNED FOR FILM GRANULATION, BELT DRIVEN BY A 100 HP 460 VOLT ONLY 1780 RPM MOTOR, GRAVITY DISCHARGE, 6″ DIAMETER X 37″ WIDE KNURLED AND GROOVED OFFSET POSITION FEED ROLL INFEED WITH PNEUMATIC PINCH, FEED ROLL IN-FEED TRUMPET, FEED ROLLS ARE CHAIN & SPROCKET DRIVEN BY A 7.5 HP 1750/1930 RPM CONTINUOUS DUTY D/C MOTOR THRU RELIANCE 2.76:1 GEARBOX, ALL MOUNTED ON LEG BASE, SWING OUT CHAMBER DOOR ON DOWNSTROKE SIDE, STARTER AND CONTROLS NOT INCLUDED

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 14098

    NELMOR G1436MB GRANULATOR W/FEED ROLLS


    NELMOR MODEL G1436MB GRANULATOR, S/N 8907-28788, 14″ X 36″ FEED THROAT, 3 KNIFE SOLID ROTOR, 2 BED KNIFE, 75 HP 230/460 VOLT MOTOR, FORKLIFT BASE, INSULATED BODY PANELS AND FEED ROLL IN-FEED HOPPER WITH 8″ X 13″ SIDE HAND FEED AND REAR CLEAN OUT DOOR, 8″ AIRVEYOR DISCHARGE, 35.5″ WIDE X 4″ DIAMETER FRONT MOUNTED KNURLED STEEL FEED ROLLS WITH PNEUMATIC OPERATED ROLL PINCH, 30″ WIDE IN-FEED TRUMPET WITH ROLLER AND DANCER BAR, FEED ROLLS ARE POWERED BY A 1 HP 90 VOLT 1750 RPM D/C MOTOR THRU 15:1 GEARBOX, INCLUDES UNITIZED 460 VOLT PANEL WITH STARTER AND CONTROLS FOR THE GRANULATOR AND A 10 HP DISCHARGE BLOWER, PENTA MODEL KDRG-2250 D/C VARIABLE SPEED CONTROLLER WITH FORWARD / REVERSE / JOG FUNCTIONS FOR THE FEED ROLLS (FIVE AVAILABLE)

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 10706

    USED TRIA 120-49/TR-NS GRANULATOR W/FEED ROLLS


    TRIA MODEL 120-49/TR-NS GRANULATOR, S/N 33.9305.96, 17.75″ X 50.25″ FEED THROAT, 5 KNIFE OPEN ROTOR WITH ADJUSTABLE KNIVES, 2 BED KNIFE WITH WATER COOLED BED KNIFE BLOCKS, 38″ WIDE STEEL FEED ROLL IN-FEED WITH DANCER BAR, 19.5 X 9.5″ FRONT PARTS IN-FEED, 50 HP 480 VOLT MOTOR, FRAME BASE, 6″ LEFT HAND AIRVEYOR, MANUAL JACK SCREW CHAMBER OPENING, .065 KW FEED ROLL MOTOR INTO GEARBOX, INCLUDES 7.5 KW PRESSURE BLOWER W/5″ OUTLET & 6″ FK160 INLET, STAND ALONE CONTROLS PANEL, AND GRANULATOR SOUND ENCLOSURE

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 6844

    NELMOR G1454MB GRANULATOR W/FEED ROLLS


    NELMOR MODEL G1454MB GRANULATOR, S/N 8007-11566, 14″ X 54″ FEED THROAT, 3 KNIFE SOLID ROTOR, 2 BED KNIFE, 50 HP 230/460 VOLT MOTOR, TRAY FEED HOPPER, AIRVEYOR DISCHARGE WITH BINDICATOR AND 4″ OD OUTLET, MOUNTED ON A 57″ TALL LEG BASE MOUNTED TO A PLATE WITH V-CASTERS, INCLUDES CONTROL PANEL WITH NEMA SIZE 4 STARTER FOR THE GRANULATOR, SIZE 2 STARTER FOR A DISCHARGE BLOWER, PANEL HAS CONTROLS FOR GRANULATOR AND BLOWER (FEED ROLLS IN PICTURES ARE NOT INCLUDED)

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 14293

    CUMBERLAND 1628 GRANULATOR W/FEED ROLLS


    CUMBERLAND MODEL 1628 GRANULATOR, S/N 98100-96514, 16″ X 28″ FEED THROAT, 3 KNIFE OPEN ROTOR, 2 BED KNIFE, 30 HP 230/460 VOLT MOTOR, INSULATED TRAY FEED HOPPER WITH REAR MOUNTED 6″ DIAMETER X 26″ WIDE POLYNETICS MODEL RF26 (S/N 6033) STEEL GROOVED FEED ROLLS IN VERTICAL POSITION WITH 7″ X 41″ WIDE IN-FEED TRUMPET TAPERING TO 26″ WIDE, FEED ROLLS ARE POWERED BY A 1 1/2 HP 180 VOLT DC 1780 RPM MOTOR DIRECT CONNECTED TO AN ELECTRA 30:1 GEARBOX AND CONTROLED BY A BRONCO II VARIABLE SPEED DRIVE, 91.5″ FEET PER MINUTE MAXIMUM ROLL SPEED, ENERPAC HYDRAULIC OPERATED HOPPER JACK BACK SYSTEM, 6″ RIGHT HAND AIRVEYOR DISCHARGE, MOUNTED ON VIBRATION PADS, COMPLETE WITH GRANULATOR STARTER AND CONTROLS

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 12907

    CUMBERLAND 584 GRANULATOR W/FEED ROLLS


    CUMBERLAND MODEL 584 GRANULATOR, S/N 335000-7670, 14″ X 20″ FEED THROAT, 3 KNIFE SLANT CUT OPEN ROTOR, 2 BED KNIFE, APPROXIMATE 15 HP 460 VOLT MOTOR, INSULATED TRAY FEED HOPPER WITH REAR MOUNTED 14.5″ TRUMPET FEED ROLL IN-FEED, SMOOTH STEEL FEED ROLLS ARE 2.5″ DIAMETER X 15.75″ LONG IN OFF-SET POSITION AND ARE PNUEMATICALLY ACTUATED, FEED ROLLS ARE POWERED BY A 2 HP 460 VOLT 1725 RPM MOTOR THRU 30:1 BOSTON GEARBOX AND IS CONTROLED BY A BALDOR A/C VARIABLE SPEED DRIVE UNIT, 6″ LEFT HAND AIRVEYOR DISCHARGE, ON CASTERS, COMPLETE WITH STARTER AND CONTROLS, 3/16″ SCREEN INSTALLED, 1976 MODEL YEAR

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 12251

    BALL & JEWEL LT-1248 GRANULATOR W/FEED ROLLS


    B&J MODEL LT-1248 GRANULATOR, S/N 37298, 12″ X 48″ FEED THROAT, 3 KNIFE OPEN ROTOR, 2 BED KNIFE, DUAL 10 HP 230/460 VOLT 1170 RPM MOTORS, DUAL FLYWHEEL, HYDRAULICALLY OPERATED INSULATED FRONT SHEET FEED HOPPER WITH A 7.5″ X 47.25″ WIDE OPENING AND TOP FEED 4″ DIAMETER X 47″ WIDE RUBBER FEED ROLLS, SIDE BY SIDE CONFIGURED, POWERED BY A 1.5 HP 180 VOLT D/C MOTOR THRU BOSTON GEAR 10:1 GEARBOX, CHAIN & SPROCKET DRIVEN AND CONTROLLED BY A SECO BRONCO II VARIABLE SPEED DRIVE, 4″ AIRVEYOR DISCHARGE, FORKLIFT RAIL BASE, INCLUDES NEW WEG DUAL MOTOR STARTER AND CONTROLS FOR THE GRANULATOR WITH INTERLOCKED 5 HP BLOWER STARTER

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 5602

    NELMOR G1012M1 GRANULATOR W/FEED ROLLS


    NELMOR MODEL G1012M1 GRANULATOR, S/N 7908-13725, 10″ X 12″ FEED THROAT, 3 KNIFE OPEN ROTOR, 2 BED KNIFE, 10 HP 230/460 VOLT MOTOR, 3/4 HP SIDE MOUNTED BLOWER DISCHARGE WITH 4″ OD OUTLET, 9″ WIDE FRONT MOUNTED KNURLED STEEL FEED ROLLS POWERED BY 3/4 HP 90 VOLT DC MOTOR, CHAIN AND SPROCKET DRIVEN, MOUNTED ON CASTER BASE, COMPLETE WITH STARTER, CONTROLS, AND VARIABLE SPEED DC DRIVE

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 6789

    PROCESS CONTROLS INC MDRFN-14 GRANULATOR W/FEED ROLLS


    PROCESS CONTROLS INC MODEL MDRFN-14 GRANULATOR, 10″ X 12″ FEED THROAT, 3 KNIFE SLANT CUT OPEN ROTOR, 1 BED KNIFE, 10 HP 230/460 VOLT MOTOR, TRAY FEED HOPPER WITH KNURLED STEEL FEED ROLLS WITH A OPENING OF 2″ X 7″, 1/2 HP FEED ROLL MOTOR, COMPLETE WITH STARTER AND VARIABLE SPEED CONTROLS FOR FEED ROLLS, MOUNTED ON CASTERS (3 AVAILABLE, TWO HAVE AIR DRIVEN FEED ROLL MOTORS)