|
| |
Quotation Request Form
Click On Any Photo To Enlarge
|
Stock
# |
Description |
Picture |
| 6691 |
HERMAN
SCHWABE MODEL SR115 STRAIGHT ARM HYDRAULIC BEAM PRESS, S/N 43343, 115 TON
CAPACITY, 53" X 30" BETWEEN TIE BARS, FOUR TIE BARS, APPROXIMATELY 8" OF
STROKE, NIP ROLL POWER FEEDER, SINGLE PLATEN, DOWN ACTING, SLAB SIDE
CONSTRUCTION, WITH ALLEN BRADLEY PANELMATE CONTROL AND PENDANT PANEL. |
      |
| 6672 |
16" X 48"
DAVIS STANDARD 16" X 48" 3 ROLL DOWNSTACK,
S/N N9057, SO# 50742, MANUFACTURED 10/93, TUNGSTEN TOP ROLL, CHROME MIDDLE & LOWER ROLLS, ALL
ROLLS ARE CORED FOR COOLING, SILENT CHAIN DRIVE, PNEUMATICALLY OPERATED, COOLED VIA
THREE 3 HP PUMPS AND HEAT EXCHANGERS, ROLLER CONVEYOR, 8" X 48" RUBBER PULL
ROLL STAND WITH SLITTER STATION, COMPLETE WITH OPERATOR STATION |
       |
| 6675 |
16" X 54"
MARSHALL & WILLIAMS 16" DIAMETER X 54"
WIDE 3 ROLL DOWN STACK, S/N 4885, SO# 27223, MSO #27221, CERAMIC ROLLS
ARE CORED FOR COOLING VIA 6 HEAT EXCHANGERS AND
THREE 3 HP PUMPS, 8" X 54" RUBBER PULL ROLL STAND
WITH SLITTER STATION, INCLUDES ROLLER CONVEYOR AND
OPERATOR CONTROL STATION WITH RELIANCE FLEX PAX
DRIVE UNIT |
      |
| 6547 |
17.75" X
34"
CINCINNATI MILICRON (MANUFACTURED BY
WELEX) 2 ROLL STACK/LAMINATOR, NO S/N, TWO CORED FOR COOLING CHROME ROLLS
17.75" DIAMETER X 34" WIDE, TWO ALUMINUM GUIDE ROLLS, ONE 17.75" DIAMETER X
31" WIDE AND ONE 8" DIAMETER X 31" WIDE CHROME ROLLS ARE PNEUMATICALLY
OPERATED AND ARE POWERED BY A 5 HP 1750 RPM 500 VOLT DC MOTOR THRU KOELLMANN
18.131:1 GEARBOX VIA SILENT CHAIN DRIVE, ROLLS COOLED VIA THREE 5 HP PUMPS
AND HEAT EXCHANGER, PULL ROLL STATION HAS TWO RUBBER COATED STEEL ROLLS
17.75" DIAMETER X 34" WIDE AND ONE 8" DIAMETER X 34" WIDE, PNEUMATICALLY
OPERATED AND
DRIVEN BY SAME DRIVE SYSTEM AS ROLL STACK, INCLUDES UNWINDER STATION WITH
APPROXIMATE 40" DIAMETER PACKAGE, DUAL TENSION CONTROLS, FOOT PEDAL
ACTUATED, NO DC DRIVES OR CONTROLS FOR ALL ITEMS, ALL SET FOR 42" CENTERLINE
|
      |
| 6522 |
PROCESSING
TECHNOLOGIES INC MODEL 5024 3 ROLL DOWN
STACK, S/N 297-CRS, MANUFACTURED 2/2000, 24" DIAMETER X 50" WIDE LOWER
2 CHROME ROLLS, UPPER ROLL IS 12" X 50", ALL CHROME ROLLS CORED FOR COOLING,
ROLLS ARE HYDRAULICALLY OPERATED AND POWERED BY A 7.5 HP DC MOTOR VIA SILENT
CHAIN DRIVE, CONTROL TECHNIQUES MENTOR II DC DRIVES FOR STACK AND PULL ROLL
STATION, PULL ROLLS PNUEMATIC OPERATION AND POWERED BY A 5 HP DC MOTOR,
COOLING VIA 3 X 10 HP PUMPS INTO HEAT EXCHANGERS |
      |
|
5671 |
12/1996
MODEL DAVIS
STANDARD 3 ROLL DOWN STACK, S.O. 56433, S/N 56422, THREE HYDRAULICALLY
ADJUSTED 24" DIAMETER X 54" WATER COOLED CORED CHROME ROLLS.
CHROME ROLLS ARE NEWLY RE-CHROMED AND ARE GEAR DRIVEN BY A 5 HP DC MOTOR THRU A GEARBOX.
CHROME ROLLS ARE COOLED BY THREE 28" HEAT
EXCHANGERS WITH 7.5 HP PUMPS, 8' UNITIZED ROLLER CONVEYOR, 8" DIAMETER
X 54" WIDE PNUEMATIC PRESSURE RUBBER PULL
ROLLS WHICH ARE DRIVEN BY A 3 HP DC MOTOR THRU A GEAR BOX. PULL ROLLS
ARE FOLLOWED BY AN ANTI-STATIC BATH USING 12" DIAMETER X 54" WIDE GUIDE
ROLL. STACK IS CONTROLLED BY A UNITIZED DAVIS STANDARD CONTROL PANEL
WITH 2 WORLDWIDE CONTROL TECHNOLOGIES MENTOR II SCR DRIVE UNITS; ONE FOR THE
CHROME ROLLS AND ONE FOR THE PULL ROLLS, 1 ALLEN
BRADLEY IMC SC/ASS BOTTOM ROLL DRIVE A/C SERVO CONTROLLER, INCLUDES OPERATOR
CONTROL STATION, EXCELLENT CONDITION |
         |
|
5672 |
JOHNSON 16"
DIAMETER X 30" WIDE THREE ROLL SHEET DOWN STACK, PNEUMATICALLY OPERATED
CORED CHROME ROLLS, ROLLS ARE DRIVEN BY A SILENT CHAIN DRIVE, DRIVE
GEARBOXES FOR BOTH THE CHROME ROLLS AND THE PULL ROLLS OPERATE AT 1.0, 2.07,
5.058, AND 10.465:1 RATIOS, PULL ROLLS ARE 8" DIAMETER X 30" WIDE AND HAVE
BEEN NEWLY RECOVERED. PULL ROLL IS DRIVEN BY A 3 HP 180 VOLT DC MOTOR THRU A
GEARBOX |
     |
|
5654 |
SAKAS TABLE
SAW MODEL TS110, S/N 15589, 3 UP-ACTING 10" DIAMETER BLADES, UNDERCUT, EACH
DRIVEN BY A 5 HP MOTOR, OVERALL DIMENSION ARE 5'W X 13'L X 6''T |
  |
|
5657 |
PROGRESSIVE
SYSTEMS DUAL RIP SAW, APPROXIMATE 10' WIDE AREA, TWO 14" DIAMETER BLADES
EACH MANUALLY ADJUSTABLE AND EACH DRIVEN BY A 10 HP 230/460 VOLT 1745 RPM
MOTOR, 44" TABLE HEIGHT, MOUNTED ON CASTERS |
 |
|
2022 |
NEW UNUSED 24:1 L/D BARREL FOR 2.5" DAVIS STANDARD EXTRUDER |
|
|
2023 |
USED 24:1 L/D BARREL FOR 2.5" DAVIS STANDARD EXTRUDER, XALLOY 800 LINER (2
AVAILABLE) |
|
|
3381 |
CHROME ROLL 20" DIAMETER X 80" LONG, CORED FOR WATER COOLING, HAS 18"
DIAMETER GEAR ON DRIVE SIDE, OVERALL LENGTH IS 104" (5 UNITS AVAILABLE) |
|
|
3384 |
CHROME ROLL 16" DIAMETER X 80" LONG |
|
|
3628 |
MELT PUMP WITH GEAR BOX, NO MOTOR OR CONTROLS |
 |
|
3790 |
TEXTURED ROLL 18" DIAMETER X 53" LONG |
 |
|
3792 |
CHROME ROLL 18" DIAMETER X 53" LONG |
|
|
4614 |
40" PULL
ROLL, PNUEMATIC PRESSURE ON TOP ROLL, TOP ROLL IS RUBBER COATED, BOTTOM ROLL
IS STEEL, DRIVEN BY A 1 HP DC MOTOR WITH GEAR BOX |
|
|
4795 |
RELIANCE 300 HP 1150/2000 RPM DC MOTOR WITH RELIANCE VS SERIES SCR DRIVE
WITH PANEL |
|
|
5268 |
DAVIS STANDARD 3 ROLL DOWN STACK, 3 18" DIAMETER X 42" WIDE CORED FOR
COOLING CHROME ROLLS, 3 HP DC MOTOR THROUGH GEAR BOX POWERING SILENT CHAIN
DRIVE, HYDRAULIC PRESSURED ROLLS, CHROME ROLLS ARE COOLED BY TWO CONAIR/TEMPRO
MODEL TC2-DI THERMOLATORS, 460 VOLTS, 26.3 MAX AMPS, 9 KW EACH, 3/H HP PUMP,
DIGITAL DISPLAY, RS232 COMMUNICATIONS PORT, HYDRAULICALLY
PRESSURED 8" DIAMETER X 53" RUBBER PULL ROLLS, PULL ROLL AND DOWN STACK ARE
MOUNTED ON V-CASTERS |
   |
|
5382 |
DAVIS STANDARD FREE STANDING TEMPERATURE CONTROL PANEL WITH FOUR BARREL AND
FIVE DIE ZONES, RKC SYSCON TEMPERATURE CONTROLLERS, 60 HP RELIANCE SCR,
MANUFACTURED 5/92 |
|
|
5401 |
NRM FORCE FEED HOPPER (CRAMER FEEDER), S/N 15728, FOR 2.5" EXTRUDER, 3 HP DC
MOTOR WITH SCR DRIVE WHICH HAS TACH AND AMP METER. |
 |
Quotation Request Form
Click On Any Photo To Enlarge
|
