Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 16397

    USED DAVIS STANDARD 2.5″ 24:1 L/D EXTRUDER


    USED 2.5” 24:1 DAVIS STANDARD MARK V EXTRUDER, S/N BN0005, SO# 84113, MANUFACTURED 4/2007, FOUR (4) ZONE ELECTRICALLY HEATED, AIR COOLED BARREL AT A 42” CENTERLINE HEIGHT. GEARBOX HAS A REDUCTION RATIO OF 17.28 TO 1 AND IS RATED AT 75 HP AT A SERVICE FACTOR OF 1.25 TO 1. GEARBOX IS BELT DRIVEN BY A 40 HP AC MOTOR WITH INVERTER CONTROL. INTEGRAL CONTROL PANEL HAS SEVEN (7) ZONES OF EUROTHERM 808 INSTRUMENTS CONSISTING OF FOUR (4) BARREL ZONES, ONE (1) CLAMP ZONE AND TWO (2) DIE ZONES. ELECTRICALLY HEATED C CLAMP WITH SWING AWAY DIE HOLDER ON THE EXTRUDER DISCHARGE. 460/3/60 INPUT POWER AT A MAXIMUM OF 100 AMPS.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16399

    USED DAVIS STANDARD 3.5″ 30:1 L/D 200 HP EXTRUDER


    USED DAVIS STANDARD MODEL MV35IN35SR 3.5 EXTRUDER, S/N K2187, SO# 99878, 30:1 L/D BARREL HAVING A SEVEN (7) ZONE ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP), AND SIDE VENTED BARREL AT A 52” CENTERLINE HEIGHT. GEARBOX HAS A 5.67:1 REDUCTION RATIO AND IS RATED AT 158 HP AT A SERVICE FACTOR OF 1.25. GEARBOX IS BELT DRIVEN BY A 200 HP 500 VOLT D/C MOTOR WITH CONTROL TECHNIQUES SCR. INTEGRAL TEMPERATURE CONTROL PANEL HAS TEN (10) ZONES OF BARBER COLEMAN CONTROLLERS. WATER COOLED FEED THROAT. BERINGER MODEL SL35 SCREEN CHANGER IS MOUNTED ON THE BARREL DISCHARGE AND INCLUDES A 3 HP HYDRAULIC POWER PACK WITH HOSES. MANUFACTURED 4/1987. 460/3/60 INPUT POWER

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16398

    USED DAVIS STANDARD 3.5″ EXTRUDER WITH TWO 1.250″ CO-EXTRUDERS


    ONE (1) USED DAVIS STANDARD CO-EXTRUSION EXTRUSION PACKAGE LAST USE ON PROFILES IN A LABORATORY ENVIRONMENT. EQUIPMENT WAS MANUFACTURED IN 2008 AND HAS LIMITED USE. EXTRUDERS AND CONTROLS ARE UNITIZED ON A SINGLE BASE. 460/3/60. 296 AMPS.

    A DAVIS STANDARD MARK V MODEL MV35IN35 3.5 24:1 L/D EXTRUDER HAVING AN ELECTRICALLY HEATED, AIR COOLED, AND NON VENTED BARREL AT A 42 CENTERLINE HEIGHT. GEARBOX HAS A 17.39:1 REDUCTION RATIO AND IS RATED AT 257 HP AT A SERVICE FACTOR OF 1.25. GEARBOX IS BELT DRIVEN BY A 100 HP MARATHON BLUE MAX HEAVY DUTY AC MOTOR WITH YASKAWA F7 HIGH PERFORMANCE INVERTER. EXTRUDER PRESENTLY SET UP FOR A MAXIMUM SCREW SPEED OF 100 RPM. INTEGRAL TEMPERATURE CONTROL PANEL HAS NINE (9) ZONES OF DAVIS STANDARD 3208 CONTROLLERS. WATER COOLED FEED THROAT WITH A 4 X 6 ENTRANCE. SERIAL NUMBER BU202. SHOP ORDER NUMBER 85499.

    B MOUNTED ON THE 3.5 EXTRUDER DISCHARGE IS AN XALOY MODEL EHC35V SCREEN CHANGER HAVING TWO NOMINAL 3.5 DIAMETER BREAKER PLATES. INCLUDES APPROXIMATELY A 2 HP HYDRAULIC POWER PACK WITH ACCUMULATOR, HOSES AND CONTROLS.

    C XALOY MODEL MS1818 917 MELT PUMP WITH 10 HP AC MOTOR, YASKAWA F7 HIGH PERFORMANCE INVERTER AND CONTROLS.

    D – TWO (2) USED DAVIS STANDARD MODEL HPE-125A 1.25 PEDESTAL EXTRUDERS HAVING ELECTRICALLY HEATED, AIR COOLED BARRELS.  UNITS ARE HEIGHT AND ANGLE ADJUSTABLE. GEARBOX IS A SEW EURODRIVE HAVING A 15.19 TO 1 REDUCTION RATIO. EACH GEARBOX IS DIRECT DRIVEN BY A MARATHON BLUE MAX HEAVY DUTY AC MOTOR WITH YASKAWA F7 HIGH PERFORMANCE INVERTER AND CONTROLS. SERIAL NUMBERS BU205 AND BU 208.  SHOP ORDER 85499.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 15038

    USED AMERICAN KUHNE AK350-A/C-EXT 3.5″ EXTRUDER


    USED AMERICAN KUHNE MODEL AK350-A/C-EXT 3.5″ EXTRUDER, S/N 1954, 24:1 L/D ELECTRICALLY HEATED AIR COOLED NON-VENTED BARREL. GEARBOX IS RATED AT 150 HP AT 1725 INPUT RPM WITH A SERVICE FACTOR OF 1.6 AND A REDUCTION RATIO OF 17.65:1. GEARBOX IS DIRECT DRIVEN BY A 75 HP AC MOTOR WITH INVERTER, INCLUDES FREE STANDING TEMPERATURE CONTROL PANEL, MANUFACTURED IN 2000

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 15037

    USED AMERICAN KUHNE AK450-A/C-EXT 4.5″ EXTRUDER


    USED AMERICAN KUHNE MODEL AK450-A/C-EXT 4.5″ EXTRUDER, S/N 1954, 30:1 L/D ELECTRICALLY HEATED AIR COOLED NON-VENTED BARREL. GEARBOX IS RATED AT 150 HP AT 1104 INPUT RPM WITH A SERVICE FACTOR OF 1.6 AND A REDUCTION RATIO OF 19.84:1. GEARBOX IS DIRECT DRIVEN BY A 150 HP AC MOTOR WITH INVERTER, INCLUDES FREE STANDING TEMPERATURE CONTROL PANEL, MANUFACTURED IN 2000

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16387

    USED MERRITT DAVIS 6″ 30:1 L/D EXTRUDER


    USED MERRITT DAVIS 6” SINGLE SCREW EXTRUDER, S/N 03089-01, 30:1 L/D ELECTRICALLY HEATED WATER COOLED BARREL 182” LONG WITH A 42” CENTERLINE HEIGHT, 6 BARREL ZONES, 3 DIE ZONES, DIRECTLY DRIVEN BY A UNUSED 500 HP (373 KW) AC MOTOR THRU FLENDER TYPE SZNF 315 GEAR BOX WITH A 12:1 GEAR BOX RATIO AND WITH A 701 HP GEAR BOX RATING, STAND ALONE CONTROL PANEL WITH AMPERAGE READOUTS PER ZONE, EUROTHERM TEMPERATURE CONTROLS, AND SOLID STATE RELAYS, PRICED WITH NEW WEG AC DRIVE UNIT IN A NEW WEG NEMA 12 ENCLOSURE WITH FULL WEG FACTORY WARRANTY (FACTORY LEAD TIME APPLIES TO NEW WEG DRIVE), EXTRUDER NEW IN 2000, APPROXIMATE DIMENSIONS 276″ X 55″ X 99″ WITH HOPPER.  CAN BE PURCHASED AS IS WHERE IS WITH NO MOTOR OR NEW DRIVE

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16050

    USED MERRITT DAVIS 6″ 24:1 EXTRUDER


    USED 6″ MERRITT DAVIS 24:1 L/D EXTRUDER, S/N WC04415-03, NON-VENTED AIR COOLED ELECTRICALLY HEATED BARREL, APPROXIMATELY 10″ X 10″ TOP CENTER FEED WITH STARVE FEEDER MOUNTED IN PLACE. DRIVEN BY 300 HP 1785 RPM AC MOTOR, 460 VOLT AC INPUT, 327 MAXIMUM AMPS CONNECTED LOAD, 13.8:1 GEARBOX SUPPLYING 125 RPM SCREW SPEED. HAS TEMPERATURE CONTROL PANEL WITH 12 EUROTHERM INSTRUMENTS, AMP METERS, AND PANELMATE TOUCH SCREEN OPERATOR CONTROL. INCLUDES FREE STANDING VARIABLE FREQUENCY DRIVE AND HAS VACUUM PUMP INSTALLED ON EXTRUDER BASE

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => extrusion-sheet-lines [3] => just-arrived [4] => extruders-3-5-10 [5] => extrusion-sheet-lines )
  • Stock#: 14893

    USED DAVIS STANDARD 6″ EXTRUDER – 46″ WIDE SHEET LINE


    USED DAVIS STANDARD 46″ WIDE SHEET LINE LAST USED ON PP SHEET AT A RATE OF 1800 LBS AN HR CONSISTING OF:

    A – DAVIS STANDARD MODEL 6IN60TPIN 6″ 30:1 L/D EXTRUDER HAVING A SIX ZONE ELECTRICALLY HEATED, WATER COOLED BARREL (CLOSED LOOP) VENTED BARREL AND PLUGGED, 47” CENTERLINE HEIGHT. GEARBOX HAS A 11.3:1 REDUCTION RATIO AND IS DIRECT DRIVEN BY A 500 HP RELIANCE DC MOTOR WITH 550 KVA ISOLATION TRANSFORMER ALLOWING FOR A MAXIMUM SCREW SPEED OF 154 RPM. GEARBOX HAS A RATING OF 700 HP AT A SERVICE FACTOR OF 1.5. FEED THROAT HAS A 12” X 8” ENTRANCE. EXTRUDER SCREW IS A BARRIER TYPE. CONTROL PANEL WITH SIX EUROTHERM 2208 TEMPERATURE CONTROLLERS FOR THE EXTRUDER BARREL ZONES PLUS 9 MORE DISCRETE CONTROLLERS FOR THE DIE AND DOWNSTREAM ZONES. S/N X7505. MFD 1998

    B – EXTEK MODEL HSC60 SCREEN CHANGER HAVING TWO NOMINAL 6” DIAMETER BREAKER PLATES. INCLUDES 2 HP HYDRAULIC POWER PACK.

    C – XALOY MODEL SPD-300 MELT PUMP WITH 25 HP DRIVE SYSTEM AND CONTROLS.

    D – EDI 44″ MODEL ULTRA-FLEX UHRC-100 FLEXIBLE LIP SHEET DIE HAVING A 45 DEGREE RESTRICTOR BAR. SET UP FOR FIVE ZONES OF TEMPERATURE CONTROL. WITH DECKELING PROVISION. INCLUDES DIE SUPPORT CART WITH CASTERS. 230 VOLT. S/N 98-20339. MANUFACTURED 1998.

    E – DAVIS STANDARD MODEL UPSTACK46 COOL-KING AND POLISHING STAND HAVING THREE NOMINAL 24” DIAMETER CHROME PLATED ROLLS MOUNTED IN A VERTICAL ARRANGEMENT FOR UP-STACK OPERATION. HYDRAULICALLY ACTUATED CHROME ROLLS ARE EACH DRIVEN BY A 3 HP INVERTER DUTY MOTOR WITH ENCODER THRU SEW EURODRIVE 86.34:1 GEARBOXES WITH A 0-1750 RPM SPEED RANGE. INCLUDES PULL ROLL STAND WITH 46” X 8” DIAMETER ROLLS WITH 5 HP DRIVE SYSTEM AND 20′ IDLER CONVEYOR AND THREE ZONE WATER TEMPERATURE CONTROL SYSTEM WITH HEATERS, HEAT EXCHANGERS, AND 7.5 HP PUMPS.

  • Array ( [0] => just-arrived [1] => dust-collectors-filters [2] => just-arrived [3] => dust-collectors-filters )
  • Stock#: 16347

    USED PELLETRON XP180 DE-DUSTING SYSTEM


    USED PELLETRON MODEL XP180 DE-DUSTER SYSTEM, S/N 01701, 2013 MODEL YEAR, SALES ORDER DE13-2248, 10 HP XP180 WASH AIR FAN, 10″ STAINLESS STEEL 2 HP AIRLOCK WITH A GEAR RATIO OF 37.30:1, INCLUDES MAC PROCESS LLC (SCHENCK PROCESS) MODEL 96ST64 STYLE III DUST COLLECTOR / BAG HOUSE, S/N 1100227529-010-1, ALL IN EXCELLENT CONDITION, UP TO 29,000 LBS PER HOUR CAPACITY (MATERIAL TYPE AND BULK DENSITY DEPENDENT)

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => extrusion-sheet-lines [3] => lab-testing-equipment [4] => just-arrived [5] => extruders-34-3 [6] => extrusion-sheet-lines [7] => lab-testing-equipment )
  • Stock#: 15071

    USED DAVIS STANDARD 3/4″ EXTRUSION LAB SHEET LINE


    USED DAVIS STANDARD LABORATORY SHEET EXTRUSION LINE CONSISTING OF THE FOLLOWING:

    A) 3/4″ 24/1 MODEL KLJ-075 24:1 L/D PEDESTAL EXTRUDER HAVING A THREE(3) ZONE ELECTRICALLY HEATED, AIR COOLED BARREL. GEARBOX HAS A REDUCTION RATIO OF 15:1 AND IS DRIVEN BY A 1.5 HP 1750 RPM AC MOTOR WITH INVERTER. FREE STANDING CONTROL PANEL WITH EUROTHERM 2208 TEMPERATURE CONTROLS FOR 3 BARREL ZONES, 2 DIE ZONES, 1 CLAMP RING, AND ONE 1 MELT PUMP. MANUFACTURED 02/2002. GENERAL PURPOSE EXTRUSION SCREW INSTALLED. S/N AG057, S/O 74488, 230/3/60 INPUT.

    B) 4″ SHEET DIE INSTALLED ON EXTRUDER DISCHARGE.

    C) WAYNE YELLOW JACKET SHEET STACK HAVING THREE (3) 8.5” FACE X 5.5″ WIDE CHROME ROLLS MOUNTED IN A VERTICAL ARRANGEMENT. WITH ROTARY UNIONS, PULL ROLLS, SURFACE WINDER AND CONTROLS.

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 16275

    USED WAYNE 1″ 30:1 L/D EXTRUDER


    USED 1″ WAYNE 30:1 L/D EXTRUDER HAVING A THREE (3) ZONE ELECTRICALLY HEATED, AIR COOLED NON-VENTED BARREL AT APPROXIMATELY A 39″ CENTERLINE HEIGHT. GEARBOX IS BELT DRIVEN BY A 5 HP DC MOTOR WITH SCR CONTROL. EXTRUDER DISCHARGE HAS A MANUAL SCREEN CHANGER, STATIC MIXER AND A 4 HOLE STRAND DIE ON THE DISCHARGE. UNITIZED TEMPERATURE CONTROL PANE HAS SIX ZONES OF 1/8 DIN CONTROLLERS CONSISTING OF ZONES FOR THREE (3) BARREL, ONE (1) SCREEN CHANGER, (1) STATIC MIXER AND ONE (1) ZONE FOR THE STRAND DIE. SERIAL NUMBER 7502. MANUFACTURED 2003. 230/1/60 OPERATION

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 16355

    USED WAYNE 1.250″ 30:1 L/D EXTRUDER


    USED WAYNE 1.25″ EXTRUDER, S/N 9414-832, 30:1 L/D, ELECTRICALLY HEATED AIR COOLED VENTED (PLUGGED) BARREL, DRIVEN BY A 7.5 HP D/C MOTOR WITH SCR CONTROL, 230 VOLT INPUT POWER, TRACK WHEEL BASE, INCLUDES SPARE SCREW