Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 17437

    USED DAVIS STANDARD 1/4″ TUBING EXTRUSION LINE


    Davis Standard 1/4″ tubing extrusion line including the following equipment:

    A. Davis Standard / Killion model KN-100 1.00″ 24:1 L/D extruder having a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 39″ centerline height. Gearbox is belt driven by a 3 HP D/C motor with SCR control. Unitized temperature control panel has six (6) zones of Eurotherm controllers consisting of three (3) zones for the barrel and three (3) zones for the c-clamp and die. C-clamp is mounted on the discharge. Includes gravity feed hopper. BOM number 05180. 230V/1ph/50-60Hz input, 47 FLA.

    B. Nominal ¼” diameter electrically heated tubing die.

    C. Davis Standard / Killion medical tubing vacuum tank measuring 116″ long with an 8″ x 8″ cross section. Stainless steel construction. Two glass doors. Upstream and downstream adjustment as well as up and down adjustment. Includes vacuum pump with 3 HP D/C motor, water pumps, sizing fixture, and controls. S/N 30176. 230V/1ph/60Hz input.

    D. Davis Standard / Killion belt puller having a 2″ wide belt with 22″ of contact length. Powered by an approximate 1.5 HP D/C motor. Manually actuated top belt. S/N 30174. 230V/3ph/60Hz input, 10 FLA.

  • Array ( [0] => just-arrived [1] => injection-molding [2] => just-arrived [3] => injection-molding )
  • Stock#: 17397

    USED FERROMATIK MILACRON VISTA V55 MOLDING MACHINE


    Ferromatik Milacron model Vista V55 injection molding machine. Unit has a clamping force of 55 tons and a 1.76 oz shot capacity. Toggle clamp. 12.8″ x 12.2″ tie bar spacing. Platens measure 20.08? x 19.67″. Clean machine with 6170 original hours. Siemens Xtreem NT controller upgraded to Xtreem ST in 2017. S/N S55A0500076. Manufactured in 2002. Manual included. 460V/3ph/60Hz input. 6,500 lbs. 11′ x 4′ x 6′. Previously used in a college laboratory.


  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17406

    USED DAVIS STANDARD 6″ 30:1 L/D EXTRUDER


    Davis Standard model 600STVW 6″ 30:1 L/D extruder, S/N 7-69006. Extruder has a five (5) zone electrically heated, water cooled non vented barrel at a 42″ center-line height. Gearbox has a reduction ratio of 17.38:1 and is rated at 300 HP at a service factor of 1.5. Gearbox was rebuilt by AES in august of 2014. Shaft mounted oil pump and filter. Gearbox is belt driven by a 300 HP 1150/2000 RPM field weakened D/C motor with SCR control. Water cooled feed throat has Conair mixer and bunting magnet mounted on the entrance. Temperature control panel has seven (7) zones of controllers. Cored extrusion screw with rotary union. C-clamp on the barrel discharge. Pulled from service 3/2021 as product line was discontinued

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-spin-dryers [3] => just-arrived [4] => pelletizers [5] => pelletizing-spin-dryers )
  • Stock#: 17408

    USED GALA MAP-6 PELLETIZING SYSTEM


    Gala model MAP-6 pelletizing system including cutter with 4 kW motor, die, and water box mounted on a stand. 40 GPM tempered water system with pump, reservoir, heater, heat exchanger, and model 2008-BF spin dryer. Free standing OEM control panel. 460V/3ph/60Hz operation. 64 full load amps. S/N 10200656. Manufactured in 2001. Last used with a 6″ 30:1 300HP Davis Standard extruder.

  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17407

    USED LEISTRITZ 50mm TWIN SCREW EXTRUDER


    Leistritriz 50mm twin screw compounding extruder with a 40:1 L/D ratio. Screws are co-rotating and inter-meshing at a 42″ center-line height. Feed entrance is 3″ x 3″. Barrel is electrically heated and water cooled and consists of ten (10) barrel sections including feed, top vent, side feed, and seven (7) closed sections. Screws and barrel sections were replaced in 2016. Eisenbeiss gearbox was replaced in 2015 and is direct driven by a 54 KW (72 HP) A/C motor with Emerson Quantum III control. Gearbox is rated at 2 x 600 newton meters. Free standing control panel with eleven (11) zones of temperature controls that also houses the drive control and operator controls. Package includes Leistritz side feeder with twin screws and 1.5 kw drive and 2.2 kw water centrifugal vacuum pump with micron technology filter. Pulled from service in March of 2021. Last used for compounding LDPE. 460V/3ph/60Hz. 250 amp main disconnect.

  • Array ( [0] => just-arrived [1] => mixers [2] => just-arrived [3] => mixers )
  • Stock#: 17422

    USED JAEGER RE-900 ROTARY BATCH MIXER


    Jaeger model RE-900 steel rotating batch blender, 403 cubic foot working capacity, carbon steel construction. Direct driven by a 40 HP motor through a gear reducer. Previously used for batch blending approximately10,000 pounds of plastic with additives.

    Two are available.

  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => pelletizing-lines [3] => just-arrived [4] => extruders-twin-screw [5] => pelletizing-lines )
  • Stock#: 17395

    USED LEISTRITZ/GALA 27mm COMPOUNDING LINE


    Leistritz / Gala 27mm compounding line consisting of the following components:

    One 27mm 40:1 Leistritz model Micro 27 40GL/40D twin screw extruder with co-rotating inter-meshing screws. Barrel is electrically heated, water cooled and consists of nine (9) barrel sections. Gearbox is direct driven by a 10.5 KW (14.3 HP) DC motor with SCR (silicone controlled rectifier) allowing for an approximate maximum screw speed of 500 RPM. Integral movable control panel has eleven (11) zones of temperature control and all operator controls. Includes pre-polymer metering pump and three (3) sets of screw shafts with loose screw elements. Manufactured in 1997. S/N 2553. Pulled from service in January of  2021. Gala model 6PDV polymer diverter valve with 10 HP hydraulic pump. Unit is used until the extruder is up to speed. Gala model SLC6 underwater pelletizer with 4.3 KW (5.3 HP) spring loaded cutter, model 40TWS water tempering system with heated reservoir, 3 HP water pump, heat exchanger, Gala model 8.1BF spin dryer with agglomerate catcher and free-standing control panel with touch screen controls. Offered less die. Includes spare blades, heater bands, and manuals. 460V/3ph/60Hz 46 FLA operation . Manufactured in 2000. S/N 10100743.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17362

    USED NRM 4.5″ 24:1 L/D 150 HP EXTRUDER


    One (1) used NRM 4.5″ 24:1 L/D PM III extruder having a six (6) zone electrically heated, water cooled (closed loop) barrel at a 42″ center-line height. Gearbox has a reduction ratio of 25.14:1 and is rated at 141 HP at a service factor of 1.25. The gearbox is direct driven in a tuck under manner by a 150 HP Reliance D/C motor with Reliance SCR. Gearbox has an oil pump and heat exchanger. The extruder has a water-cooled feed throat with 4.5” on center round  entrance. The temperature control panel has six (6) zones for the barrel and four (4) zones of temperature controls for die zones. Handi-clamp on the discharge. Temperature control 460/3/60 180 FLA. Drive Control 460/3/60. S/N 18080, Shop order 108597. Manufactured 7/1982. Includes gravity feed hopper and spare drive

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17345

    LOW HOURS LINDNER L1100 SHREDDER SYSTEM


    Little used Lindner shredding system (2011) with approximately 50 hours of use. System includes the following:

    A. Hydraulic bin tipping unit with safety cage.

    B. 700mm (27.5″) wide in feed conveyor with 2,000mm (6’5″) long straight section and 4,500mm (14’6″) incline section at 30 degrees. 1,500mm (4’8″) long horizontal discharge section. Conveyor is chain driven with PVC belt and 76mm (3″) chain pitch. Variable speed with controls.

    C. Vega Model L1100 single shaft shredder with an 1,100mm (43.3″) wide entrance with a 48 knife rotor. 1,080mm x 1,124mm throat opening (42″ x 44″). Voltage is 400V/3ph/50Hz – 460V/3ph/60Hz input. Rotor is belt driven by a 55 kW (71.5 HP) drive at 50 Hz or 63 kW (81.9 HP) drive at 60 Hz. Last used on 400V/3ph/50Hz. 50mm screen installed. PLC controlled. S/N 1630

    D. 700mm (27.5″) wide discharge conveyor with 2,000mm long straight section and 8,000mm long inclined section. Variable speed with controls.

    Located in the United Kingdom.

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17333

    USED CALIFORNIA PELLET MILL CONDITIONER


    One (1) California Pellet Mill conditioner for use with a pellet mill. Mixing section measures approximately 28″ in diameter x 8′ long. Unit is belt driven by approximately a 15 HP motor through a gear reducer

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17329

    USED CHAMPION 20″ X 44″ HAMMER-MILL


    One (1) used Champion model 20″ x 44″ Magnum hammer-mill. Unit has 2,400 cubic inches of screen area with a 3/16″ screen installed. 200 HP 1800 RPM motor supplies a 20,730 RPM tip speed. 44″ diameter rotor. Serial number 102396. 460/3/60, 230 amps.

  • Array ( [0] => just-arrived [1] => as-is-granulators-30-hp [2] => just-arrived [3] => as-is-granulators-30-hp )
  • Stock#: 17337

    USED CMG / CUMBERLAND 1842i GRANULATOR SYSTEM


    Cumberland / Gloucester model 1842i granulator. 18″ x 42″ feed throat with three (3) knife open rotor. Rotor is belt driven by a 100HP 1,775 RPM 460V 134 FLA motor. Two (2) bed knives. Insulated tray feed hopper with 19.5″ x 42″ opening. Insulated body panels. Set up for 6″ OD airveyor discharge. Discharge is via a Sterling model 6005FV blower with a 7.5 HP motor. Includes a free standing console type control panel with Alan Bradley Dialog Plus soft starter. Granulator S/N 01703024.

    Price: $42,500.00, as is.

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17322

    USED COLORADO MILL EQUIPMENT C5 PELLET COOLER


    Colorado Mill Equipment model C5 pellet cooler (now replaced by the c6). Rated at 3 to 6 tons per hour of pellets depending on pellet size, density, temperature and composition. Unit has a nominal 55″ x 55″ variable swing discharge grid with a dwell time of 10 to15 minutes. Includes optional cyclone with 17″ inlet and 11″ outlet, 15 HP blower, screener, and top airlock with a 10″ x 12″ entrance and 1 HP motor with gearbox. limited use. extremely clean.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17340

    USED DAVIS STANDARD 6″ 30:1 L/D EXTRUDER


    Davis Standard model 60IN60TPIH 6″ 30:1 L/D extruder having a six (6) zone electrically heated, water cooled (closed loop) non-vented barrel at a 42″ center-line height. Oversize heavy-duty gearbox has a reduction ratio of 11.29:1 and is rated at 706 HP at a service factor of 1.5. The gearbox is set up for a direct drive from the back of the extruder. Gearbox has an oil pump with heat exchanger for lubrication and cooling. The extruder has a water-cooled feed throat with 6″ wide x 9″ long on center entrance. Air actuated C-clamp with swing away die holder on the discharge. S/N S-4866, Shop order S6300. Manufactured 10/96. Offered less panel, motor and drive

  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => as-is-granulators-30-hp [3] => just-arrived [4] => 75-hp-granulators [5] => as-is-granulators-30-hp )
  • Stock#: 17335

    USED GRANUTEC TFG3636-125 GRANULATOR SYSTEM


    Granutec model TFG3636-125 granulator having a 36″ x 36″ feed throat. Tangential cutting chamber with three (3) knife open rotor. Two (2) bed knives. Rotor is belt driven by a 125 HP 460-volt 1185 RPM 146 FLA motor. Tray feed hopper. Granulator and controls are mounted on a base plate with fork lift rails. Discharge is set up for an 8″ right hand airveyor. Discharge is via a Kongskilde model MTD-35 blower with 15 HP motor and steel reinforced impeller. Blower discharges into a Kongskilde model RC40 cyclone with nine (9) bag filter head, Kongskilde RF20 rotary valve, and material holding bin. Bin measures 48″ x 48″ x 127″ tall plus 24″ of 45-degree slope. Bin also has 6″ OD gaylord height discharge, Granulator S/N 1205-4296.

    Price: $99,500.00, as is.

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17319

    USED SPROUT WALDRON SW26 PELLET MILL


    One (1) used Sprout Waldron model 26 pellet mill having a 26″ diameter die with ¼” holes. Unit was recently rebuilt and was used for test runs on wood pellets and alfalfa. 11″ x 13″ feed entrance with 5 HP feeder. Conditioner is mounted over the pellet mill and has a 10 HP drive and discharges into the feed entrance of the mill. Unit is direct driven by a 300 HP A/C motor with Motortronics VMX series soft start. extremely clean. serial number 82-244. 460/3/60 operation.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17315

    USED DAVIS STANDARD 4.5″ 20:1 L/D RUBBER EXTRUDER


    Davis Standard model 45IN45H 4.5″ 20:1 L/D rubber extruder having a four (4) zone electrically heated, water cooled (closed loop), vented barrel at a 49″ center-line height. Heavy-duty gearbox has a reduction ratio of 17.36:1 and is rated at 300 HP at a service factor of 1.5. Set up for maximum screw speed RPM of 100. The gearbox is direct driven in a tuck under manner by approximately a 150 HP Reliance D/C motor. The extruder has a water-cooled feed throat with power feed for cold feeding rubber. The barrel is vented and a has a vacuum pump mounted on the base. C-clamp with swing away die holder on the discharge. S/N J5585, Shop order 97702C. Manufactured 3/1985. 460/3/60 input.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17269

    USED DAVIS STANDARD 8″ 24:1 400 HP EXTRUDER


    Davis Standard model 80IN80H 8″ 24:1 L/D extruder having  a five (5) zone electrically heated, water cooled (closed loop) barrel at a 42″ center-line height. Oversize heavy-duty gearbox has a reduction ratio of 23.93:1 and is rated at 1080 HP at a service factor of 1.5.Set up for maximum screw speed RPM of 100. The gearbox is direct driven in a wrap-around manner by a 400 HP 1755 RPM Reliance A/C motor with Rockwell Automation inverter and isolation transformer.  The extruder has a water-cooled feed throat with 7” wide x 10” long on center entrance.  The temperature control panel has five (5) zones for the barrel and eight (8) zones of temperature controls for die zones. C-clamp with swing away die holder on the discharge. Last used on HDPE. Includes three component blending hopper which is driven off of the main gearbox. Spare Barrier screw for the extruder.  S/N 77621, Shop order G8739. Manufactured 3/28/2000. Gearbox updated 1/28/2004. 460/3/60 input. Extremely clean.

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17213

    USED SHRED-PAX AZ-80 TWIN SHAFT SHREDDER


    Shred-Pax model AZ-80 twin shaft shredder, S/N 160-9216. 33″ x 63″ wide cutting chamber entrance. Carbon steel construction. Two rows of intermeshing knives measuring 1-3/4″ thick. Each shaft is driven by a 40HP 230/460V 1,750 RPM Sumitomo AC motor run through a Sumitomo CYCLO reducer. Mounted on a steel frame. Manufactured in 1992. Overall dimensions are 149″ x 53″ 94″. This machine is offered less the controls.

  • Array ( [0] => just-arrived [1] => pelletizing-lines [2] => just-arrived [3] => pelletizing-lines )
  • Stock#: 17162

    USED 4.5″ STERLING / BERINGER PELLETIZING LINE


    Sterling extruder with an electrically heated, air-cooled, and side vented barrel at a 42″ center-line height. 4.5″ 30:1 L/D. Gearbox is a Lufkin change gear type and is direct driven in a tuck under manner by a 150HP DC motor with SCR. Includes gravity feed hopper. Integral control panel with six zones of temperature control, SCR and pelletizer controls. Berringer model 17 hydraulic slide plate screen changer having two (2) nominal 4.5″ diameter breaker plates is mounted on the extruder discharge. Includes 2HP hydraulic power pack. Following the screen changer is a Berringer model WRP12 water ring pelletizing system with a 3HP cutting head. 45 hole die tempered water system sluice-way and 2HP centrifugal spin dryer. Pulled from service in January of 2020.