Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17238

    USED VECOPLAN RG62/150 SPK-FF SHREDDER


    Vecoplan Model RG62/150 SPK FF Shredder, S/N 9227010, 2006 model year, refurbished by Vecoplan in 2014, control panel replaced new 2014, 63″ x 80″ long ram with abrasion resistant top plate, 15″ diameter x 63″ wide hard-faced rotor with self-cleaning side pockets, 74 primary 4-way index-able hardened cutters and 36 auxiliary nip cutters, 130 RPM rotor powered by a 150 HP 460 volt motor thru clutch and gearbox, Sure Cut film and fiber processing package, selling shredder only – downstream equipment pictured is not included, under power and in use with approximately 15,000 hours service since 2014 rebuild, recent work includes new clutch seals, ram top plate right & left edge w/hardox metal strips, and cylinders repacked 02/2020, new set of cutters, counter knife, guide rails, wipers installed 03/2020

  • Array ( [0] => just-arrived [1] => mixers [2] => ribbon-blenders [3] => just-arrived [4] => mixers [5] => ribbon-blenders )
  • Stock#: 17184

    USED EIRICH/AMERICAN PROCESS SYSTEMS T-500 PADDLE/RIBBON MIXER


    ONE (1) USED EIRICH / AMERICAN PROCESS SYSTEMS MODEL T-500 CYLINDRICAL RIBBON/PADDLE MIXER HAVING A TOTAL VESSEL VOLUME OF 854 CU. FT. VESSEL MEASURES 8′ IN DIAMETER X 17′ LONG. ALL CONTACT PARTS ARE MANUFACTURED OF 316 STAINLESS STEEL. TANK IS ½ THICK WITH 1″ THICK END PLATES. MAIN SHAFT IS 6.5″ SOLID 316 STAINLESS STEEL. RIBBONS MEASURE ½ “THICK X 3″. PADDLES ARE ¾” THICK. 304 STAINLESS STEEL DIMPLE JACKET IS ASME CODED AND RATED TO 150 PSI @ 350 DEGREES F. JACKET HAS FOUR (4) 2″ INLETS AND FOUR (4) 2″ OUTLETS. DISCHARGE IS VIA A 24″ DIAMETER CARBON STEEL SCREW CONVEYOR. APPROXIMATE OVERALL DIMENSIONS OF THE UNIT ARE 32′ X 8′ X 8′. UNIT WEIGHS 34,355 POUNDS. RIBBON AND PADDLES ARE DIRECT DRIVEN BY A 75 HP AC MOTOR WITH DYNAMIC COUPLING THROUGH A EURO DRIVE GEAR REDUCER WITH A 147.56/1 REDUCTION RATIO ALLOWING FOR A 12-RPM ROTOR SPEED. 24″ DIAMETER CLAMPED MANWAY ON TOP. NATIONAL BOARD NUMBER: 62. 42″ X 42″ CLEAN OUT DOOR. HAS END BOTTOM DISCHARGE APPROXIMATELY 10″ OD FOR CLEAN OUT. MANUFACTURED 1995. SERIAL NUMBER 4305A. SHOP ORDER NUMBER 4305

  • Array ( [0] => just-arrived [1] => dust-collectors-filters [2] => screeners-sifters [3] => just-arrived [4] => dust-collectors-filters [5] => screeners-sifters )
  • Stock#: 17185

    USED FORSBERGS 250V VACUUM GRAVITY SEPARATOR


    FORSBERGS, INC MODEL 250V-LH VACUUM GRAVITY SEPARATOR, S/N 12972, 22″ OD INLET, 23″ OD OUTLET, 3 HP 230/460 VOLT VIBRATORY MOTOR, 50 HP 230/460 VOLT MODEL 23H-LH DIRECT DRIVE VACUUM BLOWER, 85″ X 139″ INSTALLED FOOT PRINT, 5000-14,000 CFM RANGE, APPROXIMATELY 3,900 LBS

  • Array ( [0] => just-arrived [1] => mixers [2] => just-arrived [3] => mixers )
  • Stock#: 17182

    USED KELLY DUPLEX 667 CUBIC FOOT VERTICAL MIXER


    KELLY DUPLEX VERTICAL BLENDER, S/N 67587-F32027, 667 CUBIC FOOT CAPACITY, APPROXIMATE 570 CUBIC FOOT WORKING CAPACITY, STAINLESS STEEL CONSTRUCTION, INCLUDES SPARE SCREW AND APPROXIMATELY 6″ X 15′ LONG SCREW DISCHARGE, INTERNAL AUGER IS BELT DRIVEN BY A 30 HP MOTOR, MATERIAL IS LOADED IN THE BOTTOM FILL TROUGH AND DISCHARGED THROUGH THE VERTICAL AUGER ATTACHED TO THE SIDE, INCLUDES SPARE INTERNAL AND DISCHARGE AUGERS, STARTER / CONTROLS NOT INCLUDED

  • Array ( [0] => just-arrived [1] => mixers [2] => ribbon-blenders [3] => just-arrived [4] => mixers [5] => ribbon-blenders )
  • Stock#: 17183

    USED LOX 66 CU FT DOUBLE RIBBON MIXER


    66 CUBIC FOOT LOX DOUBLE RIBBON BLENDER, S/N 70805, MANUFACTURED IN 1990. HAS STAINLESS STEEL SHELL AND JACKET WITH MAXIMUM JACKET WORKING PRESSURE 125 PSI AT 350 DEGREES F. NATIONAL BOARD #3982. HAS APPROXIMATELY 25 HP MOTOR

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17214

    USED VECOPLAN RG52/100SPK SHREDDER


    VECOPLAN MODEL RG52/100SPK SINGLE SHAFT SHREDDER, S/N 8124010, 2005 MODEL YEAR, 15″ DIAMETER ROTOR WITH 60 PC DOUBLE ROW OF BOLT ON 40mm INDEX ABLE CUTTERS, ROTOR IS POWERED BY A 63 KW (85 HP) 480 VOLT MOTOR, HYDRAULIC POWERED RAM, ORIGINAL OEM 480V TOUCH SCREEN CONTROL PANEL, 2″ HOLES SCREEN, INCLUDES 25′ LONG IN-FEED CONVEYOR WITH 41″ WIDE FLAT BELT AND 36″ TALL SIDE WALLS, POWERED BY A 2 HP 460 VOLT MOTOR, ALSO INCLUDES TAKE-AWAY CONVEYOR WITH 16″ WIDE BELT WITH 1.5″ TALL CLEATS 48″ ON CENTER AND IS 153″ TOTAL LENGTH, POWERED BY A 1 HP 460 VOLT MOTOR AND HAS MAGNETIC HEAD PULLEY

  • Array ( [0] => just-arrived [1] => dicers [2] => just-arrived [3] => dicers )
  • Stock#: 17167

    USED CUMBERLAND 3-1/2 DICER


    USED CUMBERLAND STAIR STEP DICER, HAVING A 3 ½ “ ENTRANCE. MANUALLY ACTUATED TOP PULL ROLL. EIGHT KNIFE ROTOR WITH BOLT-ON BLADES. ROTOR AND PULL ROLLS ARE DRIVEN BY A 10 HP MECHANICAL VARI-DRIVE. MOUNTED ON CASTERS FOR MOBILITY. INCLUDES MOTOR  STARTER, E-STOP, AND ELECTRICAL DISCONNECT. S/N 27130-671. 460/3/60 INPUT

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17172

    USED RAPID EH-52/37 100 HP SHREDDER


    RAPID (REPUBLIC MACHINE) MODEL EH-52-10-15-2-60-D (EH52/37) SHREDDER, S/N 760374916, 15″ DIAMETER X 52″ WIDE WATER COOLED ROTOR WITH 74 CUTTERS IN A DOUBLE ROW CONFIGURATION, 40mm CROWN CUTTERS WITH BOLT IN CUTTER HOLDER UPGRADE, POWERED BY A 100 HP 460 VOLT MOTOR, HYDRAULIC OPERATED RAM, 8″ OD AIRVEYOR DISCHARGE, BELT DRIVE THROUGH A GEAR BOX, 51.5″ X 42″ RAM AREA, 60.5″ LONG X 51.5 WIDE X 30″ TALL HOPPER, 121.5 X 90″ FOOT PRINT, 90.5″ OVERALL INSTALLED HOPPER HEIGHT, INCLUDES HYDRAULIC PUMP FOR THE RAM AND THE ORIGINAL OEM ALLEN BRADLEY COLOR TOUCH SCREEN CONTROL PANEL / DRIVE UNIT

  • Array ( [0] => just-arrived [1] => pelletizing-lines [2] => just-arrived [3] => pelletizing-lines )
  • Stock#: 17162

    USED 4.5″ STERLING / BERINGER PELLETIZING LINE


    4.5″ 30:1 L/D STERLING EXTRUDER HAVING AN ELECTRICALLY HEATED, AIR- COOLED AND SIDE VENTED BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX IS A LUFKIN CHANGE GEAR TYPE AND IS DIRECT DRIVEN DRIVEN IN A TUCK UNDER MANNER BY A 150 HP DC MOTOR WITH SCR. INCLUDES GRAVITY FEED HOPPER. INTEGRAL CONTROL PANEL WITH SIX ZONES OF TEMPERATURE CONTROL, SCR AND PELLETIZER CONTROLS. BERINGER MODEL 17 HYDRAULIC SLIDE PLATE SCREEN CHANGER HAVING TWO (2) NOMINAL 4.5″ DIAMETER BREAKER PLATES IS MOUNTED ON THE EXTRUDER DISCHARGE. INCLUDES TWO HP HYDRAULIC POWER PACK. FOLLOWING THE SCREEN CHANGER IS A BERINGER MODEL WRP12 WATER RING PELLETIZING SYSTEM WITH 3 HP CUTTING HEAD, 45 HOLE DIE, TEMPERED WATER SYSTEM, SLUICE-WAY, AND 2 HP CENTRIFUGAL SPIN DRYER. PULLED FROM SERVICE 1/2020

  • Array ( [0] => just-arrived [1] => pelletizing-lines [2] => just-arrived [3] => pelletizing-lines )
  • Stock#: 17156

    USED GLOUCESTER / BERINGER PELLETIZING LINE


    ONE 4.5″ 30:1 L/D GLOUCESTER EXTRUDER HAVING AN ELECTRICALLY HEATED, NON- COOLED AND SIDE VENTED BARREL WITH TWO HP VACUUM PUMP AT A 42″ CENTER-LINE. GEARBOX IS DRIVEN BY A 300 HP DC MOTOR WITH EMERSON SCR CONTROL. 6” X 13.5” FEED THROAT ENTRANCE. INCLUDES GRAVITY FEED HOPPER. INTEGRAL CONTROL PANEL WITH SIX ZONES OF TEMPERATURE CONTROL, SCR AND PELLETIZER CONTROLS. PRODEX HYDRAULIC SLIDE PLATE SCREEN CHANGER HAVING TWO (2) NOMINAL 4.5″ DIAMETER BREAKER PLATES IS MOUNTED ON THE EXTRUDER DISCHARGE. INCLUDES TWO HP HYDRAULIC POWER PACK. FOLLOWING THE SCREEN CHANGER IS A BERINGER MODEL WRP12 WATER RING PELLETIZING SYSTEM WITH 3-HP CUTTING HEAD, 32 HOLE DIE, TEMPERED WATER SYSTEM, SLUICE-WAY, AND 2 HP CENTRIFUGAL SPIN DRYER. EXTRUDER SCREW REBUILT 12/2019. LAST USED ON PP AT 1300 POUNDS AN HOUR, HIPS AT 1500 POUNDS AN HOUR AND HDPE AT 1100 POUNDS AN HOUR. PULLED FROM SERVICE 1/2020.

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17135

    USED ROSENTHAL 48″ SHEETER


    ROSENTHAL MODEL “WRAP-O-MATIC” WA-S-4-U, S/N 51296, 48″ WIDE SHEET, 2 HP DRIVE MOTOR, 120 VOLT OPERATION


  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17130

    DAVIS STANDARD 4.5″ 24:1 L/D 200 HP EXTRUDER


    USED 4.5″ DAVIS STANDARD / NRM 24:1 L/D EXTRUDER HAVING A FIVE (5) ZONE ELECTRICALLY HEATED AIR COOLED BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A 17.42:1 REDUCTION RATIO AND IS DIRECT DRIVEN IN A TUCK UNDER MANNER BY A RELIANCE 200 HP AC MOTOR WITH INVERTER. WATER COOLED ON CENTER FEED THROAT. BARRIER SCREW WITH MADDOX MIXER. CONTROL PANEL LESS INSTRUMENTS. DAVIS STANDARD SUPPLIED NEW COMPONENTS TO EXISTING GEARBOX IN 2005. INCLUDES XALOY MODEL EH-45 HYDRAULIC SLIDE PLATE SCREEN CHANGER ON DISCHARGE

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17123

    USED APPLETON P510 AUTOMATIC CORE CUTTER


    APPLETON MODEL P510 CORE CUTTER, S/N 12.06.12, 132″ LONG PROGRAMMABLE AUTOMATIC CORE CUTTER WITH 4-15/16″ DIAMETER MANDREL, IDC (INSTANT DIAMETER CHANGE) FOR ONE MINUTE CHANGEOVER, 6.5″ AND 6.75″ DIAMETER CARBON FIBER MANDREL SLEEVE, AUTO CORE PUSHER, AUTO CORE ADVANCEMENT VIA SERVO BALL SCREW DRIVE, OPERATOR CONTROL STATION WITH ALLEN BRADLEY PANEL VIEW HMI CONTROLS, SAFETY GUARDING, 480/3/60 INPUT POWER, INCLUDES SOME TOOLING, 2012 MODEL YEAR, REPORTED IN EXCELLENT CONDITION

  • Array ( [0] => just-arrived [1] => pelletizing-lines [2] => just-arrived [3] => pelletizing-lines )
  • Stock#: 17124

    USED DAVIS STANDARD EXTRUDER / PELLETIZING LINE


    USED PELLETIZING LINE CONSISTING OF ONE 4.5″ 24:1 DAVIS STANDARD MODEL 450H7214 EXTRUDER HAVING A FIVE (5) ZONE ELECTRICALLY HEATED WATER COOLED AND SIDE VENTED BARREL AT APPROXIMATELY A 42″ CENTER-LINE. HEAVY DUTY GEARBOX HAS A REDUCTION RATIO OF 17.21:1 AND IS RATED AT 147 HP AT A SERVICE FACTOR OF 1.5. GEARBOX IS BELT DRIVEN BY A 300 HP DC MOTOR WITH SCR CONTROL. CV CLAMP ON BARREL DISCHARGE. INCLUDES GRAVITY FEED HOPPER AND FREE STANDING CONTROL PANEL. S/N CE4265. S/O 49325HW. ALSO INCLUDES ONE (1) USED SLIDE PLATE SCREEN CHANGER HAVING TWO (2) NOMINAL 4.5″ DIAMETER BREAKER PLATES AND A BERINGER MODEL WRP12 WATER RING PELLETIZING SYSTEM WITH 2-HP CUTTING HEAD, 80 HOLE DIE, TEMPERED WATER SYSTEM WITH HEAT EXCHANGER, SLUICE-WAY, AND 5 HP CENTRIFUGAL SPIN DRYER

  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17108

    USED LEISTRITZ 50mm 40:1 L/D TWIN SCREW EXTRUDER


    USED 50MM LEISTRITZ CO-ROTATING TWIN SCREW EXTRUDER, 40:1 L/D. EXTRUDER NEW 1995, BUT INCLUDES 2013 EISENBEISS GEAR BOX SUPPLYING 400 RPM SCREW SPEED, 100 HP AC MOTOR WITH EMERSON VFD DRIVE (REPORTED RECENTLY NEW). HAS ELECTRICALLY HEATED WATER-COOLED BARREL, INCLUDES SIDE FEEDER AND TEMPERATURE CONTROL PANEL

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17107

    USED MERRITT 4.5″ 36:1 L/D EXTRUDER


    USED 4.5″ MERRITT 36:1 L/D VENTED SINGLE SCREW EXTRUDER. HAS BELT DRIVEN DIRECT CONNECTED 200 HP DC MOTOR WITH QUANTUM SCR CONTROLLER. MOTOR IS TUCK-UNDER DESIGN DIRECT CONNECTED TO GEARBOX WITH 12.45:1 RATIO, SUPPLYING 140 RPM SCREW SPEED. EXTRUDER IS EQUIPPED WITH A STRAND DIE, ELECTRICALLY HEATED WATER-COOLED BARREL, 240/480-VOLT AC INPUT. HAS WATER COOLED TOP CENTER FEED THROAT. INCLUDES SPARE SCREW

  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17064

    USED BERSTORFF 25MM TWIN SCREW EXTRUDER


    BERSTORFF 25MM TWIN SCREW EXTRUDER, TYPE ZE25. CO-ROTATING SIDE BY SIDE SCREW DESIGN. 36:1 L/D RATIO. ELECTRICALLY HEATED, AIR COOLED, BARREL CONSISTING OF EIGHT SECTIONS INCLUDING FEED THROAT, 42” BARREL CENTER LINE HEIGHT, SIDE FEEDER ENTRANCE AND VENT SECTION. ACCURATE FEEDER MOUNTED ON FEED THROAT AND K-TRON FEEDER FOR SIDE FEEDER. 15 HP DC MOTOR WITH SCR. CONSOLE TYPE CONTROL PANEL WITH SEVEN (7) ZONES OF TEMPERATURE CONTROL, OPERATOR CONTROLS AND FEEDER CONTROLS INCLUDED. MANUFACTURED 1994. 240-VOLT INPUT POWER.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17041

    USED DAVIS STANDARD 3.5″ 100 HP EXTRUDER


    USED DAVIS STANDARD MARK V MODEL MV35IN35 3.5″ 30:1 L/D EXTRUDER HAVING A FIVE (5) ZONE ELECTRICALLY HEATED, AIR COOLED BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A 17.39 REDUCTION RATIO AND IS RATED AT 158 HP AT A SERVICE FACTOR OF 1.25. GEARBOX IS BELT DRIVEN BY A 100 HP AC MOTOR WITH AN ALAN BRADLEY INVERTER. TEMPERATURE CONTROL PANEL HAS NINE (9) ZONES OF CONTROLLERS. WATER COOLED FEED THROAT. EXTRUDER, CONTROL PANEL, AND MOTOR ARE ALL UNITIZED ON A SINGLE BASE. S/N 72974, SO# AB506. MFD 2001. 460/3/60

  • Array ( [0] => just-arrived [1] => feed-paddle-roll-granulators [2] => just-arrived [3] => feed-paddle-roll-granulators )
  • Stock#: 17046

    USED TRIA TRK5030 FEED ROLL GRANULATOR


    TRIA MODEL TRK5030 FEED ROLL IN-FEED ONLY GRANULATOR, S/N 33219814, MANUFACTURED IN 2016, 11.8″ X 19.7″ WATER COOLED CUTTING CHAMBER, 15″ WIDE X 3″ DIAMETER KNURLED STEEL FEED ROLLS WITH BRASS SCRAPER, PNEUMATIC PINCH, AND WITH A LINE SPEED OF UP TO 65 FEET PER MINUTE, GRANULATOR HAS 3 KNIFE OPEN ROTOR, 2 BED KNIVES, AND IS POWERED BY A 10 HP 460 VOLT MOTOR, 4″ OD LEFT HAND AIRVEYOR DISCHARGE, 13/32″ HOLES SCREEN, COMPLETE WITH 3 HP BLOWER MODEL HT40SL AND CYCLONE MODEL AV400 MOUNTED TO A DEDICATED STAND, CYCLONE HAS A 4″ INLET AND OUTLET, GRANULATOR IS COMPLETE WITH VIBRATION CONTROL MOUNTING PADS, SOUND SUPPRESSION CABINET, KNIFE SETTING FIXTURE, STARTER AND CONTROLS FOR GRANULATOR, BLOWER, AND V/S DRIVE FOR THE FEED ROLLS.

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17048

    USED VECOPLAN V-ECO 1300 SHREDDER SYSTEM


    VECOPLAN MODEL V-ECO 1300 SHREDDER, S/N 12489 010, MANUFACTURED 2-12-15, 135 CUTTERS, (2) BED KNIFE POSITIONS – (1) ADJUSTABLE, 150 HP 460 VOLT MOTOR, ½” SCREEN – HAS 3/8″ SCREEN IN MACHINE, 3959 HOURS ON MACHINE, INCLUDES 35′ CONVEYOR, 3 HP DRIVE W/ BIG GEAR BOX – 43″ WIDE BELT – 2″ CLEATS ON 32″CENTERS, HOME MADE CUSTOM DEBRIS GUARD ENCLOSURE OVER THE TOTAL TOP OF THE SHREDDERS’ HOPPER “SEE PICTURE”, S & S METAL DETECTOR WITH 12″ HIGH CLEARANCE ABOVE BELT INCLUDES 6′ NONMAGNETIC SECTION BELOW BELTING, CUSTOM BUILT DROP OUT CHUTE POSITIONED BEFORE THE SHREDDER HOPPER TO CLEAN MATERIAL WITH METAL OFF CONVEYOR AND INTO BIN ON FLOOR, KICE 15 HP BLOWER WITH 8″ OUTLET TUBING RUNNING OVER TO 48″ DIAMETER CYCLONE RECEIVER THAT IS 7′ TALL. THE CYCLONE HAS “6” FILTER BAGS THAT HANG DOWN 8′. THE GAYLORD FILL DISCHARGE HAS A DRAWER MAGNET WITH RARE EARTH MAGNET BARS. WAS PROCESSING POST-CONSUMER JUGS & BOTTLES/POST-INDUSTRIAL SCRAP @ 3,000 LBS/HR, 90% POST-CONSUMER – 10% POST INDUSTRIAL