Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17108

    USED LEISTRITZ 50mm 40:1 L/D TWIN SCREW EXTRUDER


    USED 50MM LEISTRITZ CO-ROTATING TWIN SCREW EXTRUDER, 40:1 L/D. EXTRUDER NEW 1995, BUT INCLUDES 2013 EISENBEISS GEAR BOX SUPPLYING 400 RPM SCREW SPEED, 100 HP AC MOTOR WITH EMERSON VFD DRIVE (REPORTED RECENTLY NEW). HAS ELECTRICALLY HEATED WATER-COOLED BARREL, INCLUDES SIDE FEEDER AND TEMPERATURE CONTROL PANEL

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17107

    USED MERRITT 4.5″ 36:1 L/D EXTRUDER


    USED 4.5″ MERRITT 36:1 L/D VENTED SINGLE SCREW EXTRUDER. HAS BELT DRIVEN DIRECT CONNECTED 200 HP DC MOTOR WITH QUANTUM SCR CONTROLLER. MOTOR IS TUCK-UNDER DESIGN DIRECT CONNECTED TO GEARBOX WITH 12.45:1 RATIO, SUPPLYING 140 RPM SCREW SPEED. EXTRUDER IS EQUIPPED WITH A STRAND DIE, ELECTRICALLY HEATED WATER-COOLED BARREL, 240/480-VOLT AC INPUT. HAS WATER COOLED TOP CENTER FEED THROAT. INCLUDES SPARE SCREW

  • Array ( [0] => just-arrived [1] => 15-30-hp-granulators [2] => under-the-press-granulators [3] => just-arrived [4] => 15-30-hp-granulators [5] => under-the-press-granulators )
  • Stock#: 17103

    USED AEC WG1256 THERMOFORMING GRANULATOR


    AEC MODEL WG1256 THERMOFORMING GRANULATOR, S/N 509000-10002, 12″ X 56″ FEED THROAT, 5 KNIFE TWIN SHEAR ROTOR, 2 BED KNIFE, PADDLE WHEEL IN-FEED ASSEMBLY, 30 HP 460 VOLT MOTOR, PNEUMATIC ASSISTED CUTTING CHAMBER OPENER, PADDLES POWERED BY A 2 HP A/C INVERTER DUTY MOTOR, 8″ RIGHT HAND AIRVEYOR DISCHARGE, MOUNTED ON CASTERS, INCLUDES 10 HP BLOWER WITH ALUMINUM IMPELLER AND SOUND ENCLOSURE, STAND ALONE ORIGINAL OEM STARTER / CONTROL PANEL FOR THE GRANULATOR AND 10 HP INTERLOCKED BLOWER, 2010 MODEL YEAR.  PICTURED UPPER PULL ROLLS AND HOPPER NOT INCLUDED

  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => just-arrived [3] => 75-hp-granulators )
  • Stock#: 17102

    USED AEC AT5090 GRANULATOR


    AEC MODEL AT5090 GRANULATOR, S/N CT036250-15002, 20″ X 36″ FEED THROAT, 3 KNIFE OPEN TWIN SHEAR STEEP ANGLE ROTOR WITH ROTATING END DISKS, 2 BED KNIVES, TANGENTIAL CUTTING CHAMBER, 100 HP 230/460 VOLT MOTOR, INSULATED TRAY FEED HOPPER AND BODY PANELS, 8″ OD RIGHT HAND AIRVEYOR DISCHARGE, MOUNTED TO COMMON PLATE BASE, INCLUDES STERLING MODEL 8010FV 10 HP BLOWER WITH ALUMINUM IMPELLER AND SOUND ENCLOSURE, ORIGINAL OEM 460 VOLT STARTER / CONTROL PANEL WITH INTERLOCKED BLOWER STARTER, 2015 MODEL YEAR

  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17064

    USED BERSTORFF 25MM TWIN SCREW EXTRUDER


    BERSTORFF 25MM TWIN SCREW EXTRUDER, TYPE ZE25. CO-ROTATING SIDE BY SIDE SCREW DESIGN. 36:1 L/D RATIO. ELECTRICALLY HEATED, AIR COOLED, BARREL CONSISTING OF EIGHT SECTIONS INCLUDING FEED THROAT, 42” BARREL CENTER LINE HEIGHT, SIDE FEEDER ENTRANCE AND VENT SECTION. ACCURATE FEEDER MOUNTED ON FEED THROAT AND K-TRON FEEDER FOR SIDE FEEDER. 15 HP DC MOTOR WITH SCR. CONSOLE TYPE CONTROL PANEL WITH SEVEN (7) ZONES OF TEMPERATURE CONTROL, OPERATOR CONTROLS AND FEEDER CONTROLS INCLUDED. MANUFACTURED 1994. 240-VOLT INPUT POWER.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17042

    USED DAVIS STANDARD / NRM 4.5″ 32:1 L/D 250 HP EXTRUDER


    USED 4.5″ DAVIS STANDARD / NRM MODEL 4.5″ 32:1 L/D PM III EXTRUDER HAVING SEVEN (7) ZONE ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP) BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A 13.34:1 REDUCTION RATIO AND IS DIRECT DRIVEN IN A TUCK UNDER MANNER BY A 250 HP AC MOTOR WITH MAGNETEK VCD 703 INVERTER. INTEGRAL TEMPERATURE CONTROL WITH TEN (10) ZONES OF CONTROLLERS. . WATER COOLED FEED THROAT. S/N 19186. TEMPERATURE CONTROL PANEL 460/3/60 95 FLA. DRIVE 460/3/60 345 FLA.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17041

    USED DAVIS STANDARD 3.5″ 100 HP EXTRUDER


    USED DAVIS STANDARD MARK V MODEL MV35IN35 3.5″ 30:1 L/D EXTRUDER HAVING A FIVE (5) ZONE ELECTRICALLY HEATED, AIR COOLED BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A 17.39 REDUCTION RATIO AND IS RATED AT 158 HP AT A SERVICE FACTOR OF 1.25. GEARBOX IS BELT DRIVEN BY A 100 HP AC MOTOR WITH AN ALAN BRADLEY INVERTER. TEMPERATURE CONTROL PANEL HAS NINE (9) ZONES OF CONTROLLERS. WATER COOLED FEED THROAT. EXTRUDER, CONTROL PANEL, AND MOTOR ARE ALL UNITIZED ON A SINGLE BASE. S/N 72974, SO# AB506. MFD 2001. 460/3/60

  • Array ( [0] => just-arrived [1] => feed-paddle-roll-granulators [2] => just-arrived [3] => feed-paddle-roll-granulators )
  • Stock#: 17047

    USED TRIA TRK5030 FEED ROLL GRANULATOR


    TRIA MODEL TRK5030 FEED ROLL GRANULATOR, S/N 33221252, MANUFACTURED IN 2017, 11.8” X 19.7” CUTTING CHAMBER, 10” WIDE FEED ROLL ONLY IN-FEED, FEED ROLLS DRIVEN BY A ½ HP DRIVE MOTOR WITH A LINE SPEED OF 3 TO 50 FEET PER MINUTE, GRANULATOR HAS 3 KNIFE OPEN ROTOR, 2 BED KNIVES, AND IS POWERED BY A 10 HP 460 VOLT MOTOR, 13/32” HOLES SCREEN, COMPLETE WITH CONTROLS AND SOUND SUPPRESSION CABINET

  • Array ( [0] => just-arrived [1] => feed-paddle-roll-granulators [2] => just-arrived [3] => feed-paddle-roll-granulators )
  • Stock#: 17046

    USED TRIA TRK5030 FEED ROLL GRANULATOR


    TRIA MODEL TRK5030 FEED ROLL IN-FEED ONLY GRANULATOR, S/N 33219814, MANUFACTURED IN 2016, 11.8″ X 19.7″ WATER COOLED CUTTING CHAMBER, 15″ WIDE X 3″ DIAMETER KNURLED STEEL FEED ROLLS WITH BRASS SCRAPER, PNEUMATIC PINCH, AND WITH A LINE SPEED OF 11.9 FEET PER MINUTE, GRANULATOR HAS 3 KNIFE OPEN ROTOR, 2 BED KNIVES, AND IS POWERED BY A 10 HP 460 VOLT MOTOR, 4″ OD LEFT HAND AIRVEYOR DISCHARGE, 13/32″ HOLES SCREEN, COMPLETE WITH 3 HP BLOWER MODEL HT40SL AND CYCLONE MODEL AV400 MOUNTED TO A DEDICATED STAND, CYCLONE HAS A 4″ INLET AND OUTLET, GRANULATOR IS COMPLETE WITH VIBRATION CONTROL MOUNTING PADS, SOUND SUPPRESSION CABINET, KNIFE SETTING FIXTURE, STARTER AND CONTROLS FOR GRANULATOR, BLOWER, AND V/S DRIVE FOR THE FEED ROLLS.

  • Array ( [0] => just-arrived [1] => thermoforming [2] => just-arrived [3] => thermoforming )
  • Stock#: 17050

    USED TSL LF5.0 THERMOFORMING LINES


    TSL MODEL LOW FLEX LF5.0 THERMOFORMING LINE, 2005 MODEL YEAR, RUNNING POLYPROPYLENE MATERIAL, 52″ X 52″ MAXIMUM MOLD SIZE, CHAIN RAILS CAN BE CHANGED TO RUN MOLDS AS SMALL AS 30″, INCLUDES FORMER, TRIM PRESS, CANOPY, AND CONTROLS, CURRENTLY UNDER POWER AND RUNNING PRODUCTION, AVAILABLE JANUARY 2020 (2 AVAILABLE)

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17048

    USED VECOPLAN V-ECO 1300 SHREDDER SYSTEM


    VECOPLAN MODEL V-ECO 1300 SHREDDER, S/N 12489 010, MANUFACTURED 2-12-15, 135 CUTTERS, (2) BED KNIFE POSITIONS – (1) ADJUSTABLE, 150 HP 460 VOLT MOTOR, ½” SCREEN – HAS 3/8″ SCREEN IN MACHINE, 3959 HOURS ON MACHINE, INCLUDES 35′ CONVEYOR, 3 HP DRIVE W/ BIG GEAR BOX – 43″ WIDE BELT – 2″ CLEATS ON 32″CENTERS, HOME MADE CUSTOM DEBRIS GUARD ENCLOSURE OVER THE TOTAL TOP OF THE SHREDDERS’ HOPPER “SEE PICTURE”, S & S METAL DETECTOR WITH 12″ HIGH CLEARANCE ABOVE BELT INCLUDES 6′ NONMAGNETIC SECTION BELOW BELTING, CUSTOM BUILT DROP OUT CHUTE POSITIONED BEFORE THE SHREDDER HOPPER TO CLEAN MATERIAL WITH METAL OFF CONVEYOR AND INTO BIN ON FLOOR, KICE 15 HP BLOWER WITH 8″ OUTLET TUBING RUNNING OVER TO 48″ DIAMETER CYCLONE RECEIVER THAT IS 7′ TALL. THE CYCLONE HAS “6” FILTER BAGS THAT HANG DOWN 8′. THE GAYLORD FILL DISCHARGE HAS A DRAWER MAGNET WITH RARE EARTH MAGNET BARS. WAS PROCESSING POST-CONSUMER JUGS & BOTTLES/POST-INDUSTRIAL SCRAP @ 3,000 LBS/HR, 90% POST-CONSUMER – 10% POST INDUSTRIAL

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17023

    USED FITZPATRICK DASO 6 FITZMILL


    USED FITZPATRICK DASO 6 FITZMILL. S/N 11303, STAINLESS STEEL CONSTRUCTION. UNIT FED BY K-TRON MODEL K-2 VOLUMETRIC FEEDER. FIXED KNIFE ROTOR. ROTOR IS BELT DRIVEN BY 7.5 HP MOTOR WITH EXPLOSION PROOF CONTROLS. MOUNTED ON A STAND WITH CASTERS ALLOWING FOR A DRUM HEIGHT DISCHARGE. INCLUDES STARTER AND CONTROLS FOR FEEDER AND FITZMILL. 460/3/60. S/O NUMBER 8627

  • Array ( [0] => just-arrived [1] => just-arrived )
  • Stock#: 17015

    USED ACRISON WEIGH SCALE BATCH FEEDER


    ACRISON MODEL A405-80-50-V101-E WEIGH SCALE BATCH MATERIAL FEEDER, S/N 91265-01, MD-II WEIGH FEEDER CONTROLLER WITH TOUCH-PAD CONTROLS, USED AS A COLLEGE TRAINING UNIT, STAINLESS STEEL BATCH HOPPER, AUGER SCREW IS POWERED BY A .5 HP 90 VOLT D/C 1725 RPM D/C MOTOR, INCLUDES INSTALLED SCREW, SPARE SCREW, AND 1.75″, 2″, AND 2-3/8″ FEEDER TUBES, CAN INSTALL UP TO A 2-11/16″ SCREW, OVERALL DIMENSIONS MOUNTED TO INCLUDED CASTER CART IS 33″ X 28″ X 83″, EXCELLENT CONDITION, ALSO INCLUDES OEM MANUAL

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-lines [3] => just-arrived [4] => pelletizers [5] => pelletizing-lines )
  • Stock#: 17001

    USED AUTOMATIK / GALA MODEL SPHERO 220 UNDERWATER PELLETIZING SYSTEM


    ONE (1) USED AUTOMATIK / GALA MODEL SPHERO 220 UNDERWATER PELLETIZING SYSTEM. UNIT IS RATED UP TO 22,000 POUNDS PER HOUR. ORDER NUMBER 1018134. MACHINE NUMBER 1018144-SH-117. MANUFACTURED 2010. 460/3/60. THE SYSTEM CONSISTS OF THE FOLLOWING:

    A) HYDRAULICALLY ACTUATED START UP VALUE WITH 11 KW HYDRAULIC PUMP

    B) LIQUID HEATED DIE PLATE WITH STERLCO MODEL M2B6017-L 80 KW OIL HEATER

    C) 60 HP 36 KNIFE CUTTER HEAD WITH PNEUMATICALLY ADJUSTABLE KNIFE SHAFT

    D) CUTTING CHAMBER WITH TANGENTIAL WATER SUPPLY AND PELLET DRAIN

    E) MOVITEC MODEL VSF 90/4-2B WATER TEMPERING SYSTEM WITH FUNKE PLATE TYPE HEAT EX-CHANGER

    F) 7.5 HP SPIN DRYER WITH AGGLOMERATE CATCHER AND 1.5 HP BLOWER. (MISSING MOTOR)

    G) FREE STANDING CONTROL PANEL

    H) SUPPORT STRUCTURE FOR CUTTER, CUTTING CHAMBER, HYDRAULIC PUMP, HYDRAULIC VALE AND OPERATOR CONTROLS.

    LAST USED ON EPS MICRO BEADS

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-lines [3] => just-arrived [4] => pelletizers [5] => pelletizing-lines )
  • Stock#: 17002

    USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM


    ONE (1) USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM. UNIT IS RATED FOR UP TO 22,000 POUNDS PER HOUR. ORDER NUMBER 1019020. MACHINE NUMBER SH-204. MANUFACTURED 2013. 460/3/60. THE SYSTEM CONSISTS OF THE FOLLOWING:

    A) HYDRAULICALLY ACTUATED START UP VALUE WITH 11 KW HYDRAULIC PUMP

    B) LIQUID HEATED DIE PLATE WITH STERLCO MODEL M2B6017-L 100 KW OIL HEATER

    C) 60 HP 36 KNIFE CUTTER HEAD WITH PNEUMATICALLY ADJUSTABLE KNIFE SHAFT

    D) CUTTING CHAMBER WITH TANGENTIAL WATER SUPPLY AND PELLET DRAIN

    E) MOVITEC MODEL VSF 90/4-2B WATER TEMPERING SYSTEM WITH FUNKE PLATE TYPE HEAT EX-CHANGER

    F) 7.5 HP SPIN DRYER WITH AGGLOMERATE CATCHER AND 1.5 HP BLOWER

    G) FREE STANDING CONTROL PANEL

    H) SUPPORT STRUCTURE FOR CUTTER, CUTTING CHAMBER, HYDRAULIC PUMP, HYDRAULIC VALE AND OPERATOR CONTROLS.

    LAST USED ON EPS MICRO BEADS.

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-lines [3] => just-arrived [4] => pelletizers [5] => pelletizing-lines )
  • Stock#: 17003

    USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM


    ONE (1) USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM. UNIT IS RATED UP TO 22,000 POUNDS PER HOUR. ORDER NUMBER 1019020. MACHINE NUMBER SH-205. MANUFACTURED 2013. 460/3/60. THE SYSTEM CONSISTS OF THE FOLLOWING:

    A) HYDRAULICALLY ACTUATED START UP VALUE WITH 11 KW HYDRAULIC PUMP

    B) LIQUID HEATED DIE PLATE WITH STERLCO MODEL M2B6017-L 100 KW OIL HEATER

    C) 60 HP 36 KNIFE CUTTER HEAD WITH PNEUMATICALLY ADJUSTABLE KNIFE SHAFT

    D) CUTTING CHAMBER WITH TANGENTIAL WATER SUPPLY AND PELLET DRAIN

    E) MOVITEC MODEL VSF 90/4-2B WATER TEMPERING SYSTEM WITH FUNKE PLATE TYPE HEAT EX-CHANGER

    F) 7.5 HP SPIN DRYER WITH AGGLOMERATE CATCHER AND 1.5 HP BLOWER

    G) FREE STANDING CONTROL PANEL

    H) SUPPORT STRUCTURE FOR CUTTER, CUTTING CHAMBER, HYDRAULIC PUMP, HYDRAULIC VALE AND OPERATOR CONTROLS

    LAST USED ON EPS MICRO BEADS

  • Array ( [0] => just-arrived [1] => extrusion-screen-changers [2] => just-arrived [3] => extrusion-screen-changers )
  • Stock#: 17004

    USED GNEUSS RSF90 GENIUS SCREEN CHANGER


    ONE (1) USED GNEUSS MODEL RSF90 GENIUS SCREEN CHANGER, S/N 0113-3506, RATED FOR UP TO 2450 POUNDS AN HOUR. FULLY-AUTOMATIC, 230 VOLTS. MOUNTED ON A STAND. EXTREMELY CLEAN. INCLUDES HYDRAULIC PUMP, MAAG MODEL ES-70/70 MELT PUMP WITH 15 HP DRIVE AND EIGHT ZONE TEMPERATURE CONTROL PANEL. MANUFACTURED IN 2013

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17012

    USED PROCEDYNE PCF2430-FB THERMAL PART CLEANING SYSTEM


    ONE (1) USED PROCEDYNE MODEL PCF2430-FB THERMAL PART CLEANING SYSTEM. S/N 1827-00255, 24” X 30” BASKET FOR PARTS. CLEANING SYSTEMS IS DESIGNED TO REMOVE COATINGS FROM ALL TYPES OF HARDWARE AND PARTS – WITH NO CARBON RESIDUE. ABSOLUTE TEMPERATURE CONTROL AND THERMAL UNIFORMITY PERMITS CLEANING OF COMPLEX CRITICAL HARDWARE WITH MINIMAL RISK OF DISTORTION OR METALLURGICAL DAMAGE.  NATURAL GAS FIRED 400,000 BTU BURNER. WITH CONTROLS, CYCLONE AND OPTIONAL PROCEDYNE MODEL AB-25-1 AFTERBURNER, S/N 1627-00255, 120 VOLT SINGLE PHASE OPERATION, AFTERBURNER CAPACITY IS 15 LBS PER HOUR AT PEAK RATE

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 16964

    NEW SHRED TECH ST-25ES DUAL SHAFT SHREDDER


    NEW SHRED TECH MODEL ST-25ES DUAL SHAFT SHREDDER, S/N ST-25ES-F314, 2019 MODEL YEAR, 16″ X 14″ CUTTING CHAMBER, TWO HEXAGONAL COUNTER ROTATING SHAFTS, 5-7/8 SHAFT CENTER DISTANCE, 20 5/8″ WIDE X 7-3/4 DIAMETER TWO TEETH KNIVES, POWERED BY A 20 HP 480 VOLT GEAR REDUCED MOTOR, 21 RPM FAST SHAFT, 18 RPM SLOW SHAFT, 39,865 LBS MAXIMUM TOOTH FORCE, 31″ FROM FLOOR STAND TO STRADDLE DISCHARGE CUSTOMER SUPPLIED CONTAINER, 27″ X 29″ STANDARD FEED OPENING IN-FEED HOPPER, INCLUDES NEMA RATED CONTROL PANEL WITH PROGRAMMABLE LOGIC CONTROLLER AND FUSED LOCKABLE DISCONNECT

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16967

    USED DAVIS STANDARD 45IN45H 4.5″ EXTRUDER


    USED 4.5″ DAVIS STANDARD MODEL 45IN45H EXTRUDER, S/N Z4431, S/O 74061, 30:1 L/D VENTED AND ELECTRICALLY HEATED AIR-COOLED BARREL AT 42″ CENTER LINE HEIGHT, DRIVEN BY 200 HP AC MOTOR WITH VARIABLE FREQUENCY DRIVE. INCLUDES TEMPERATURE CONTROL PANEL BUT NO TEMPERATURE INSTRUMENTS OR HMI FOR INFORMATION INPUT. 365 HP RATED GEARBOX WITH 1.5 SERVICE FACTOR AND 17.49:1 GEAR RATIO, MANUFACTURED 12/2001. INCLUDES 4.5″ DYNISCO MODEL EH-45 SCREEN CHANGER WITH HYDRAULIC PUMPING SYSTEM, S/N EH45208