One (1) used NRM 4.5″ 24:1 L/D PM III extruder having a six (6) zone electrically heated, water cooled (closed loop) barrel at a 42″ center-line height. Gearbox has a reduction ratio of 25.14:1 and is rated at 141 HP at a service factor of 1.25. The gearbox is direct driven in a tuck under manner by a 150 HP Reliance D/C motor with Reliance SCR. Gearbox has an oil pump and heat exchanger. The extruder has a water-cooled feed throat with 4.5” on center round entrance. The temperature control panel has six (6) zones for the barrel and four (4) zones of temperature controls for die zones. Handi-clamp on the discharge. Temperature control 460/3/60 180 FLA. Drive Control 460/3/60. S/N 18080, Shop order 108597. Manufactured 7/1982. Includes gravity feed hopper and spare drive
Little used Lindner shredding system (2011) with approximately 50 hours of use. System includes the following:
A. Hydraulic bin tipping unit with safety cage.
B. 700mm (27.5″) wide in feed conveyor with 2,000mm (6’5″) long straight section and 4,500mm (14’6″) incline section at 30 degrees. 1,500mm (4’8″) long horizontal discharge section. Conveyor is chain driven with PVC belt and 76mm (3″) chain pitch. Variable speed with controls.
C. Model Vega L1100 single shaft shredder having an 1,100mm (43.3″) wide entrance with a 48 knife rotor. 1,080mm x 1,124mm throat opening (42″ x 44″). Voltage is 400/3/50 – 460/3/60 input. Rotor is belt driven by a 55 KW (71.5 HP) drive at 50 Hz or 63 KW (81.9 HP) drive at 60 Hz. Last used on 400/3/50. 50mm screen installed. PLC controlled. S/N 1630
D. 700mm (27.5″) wide discharge conveyor with 2,000mm long straight section and 8,000mm long inclined section. Variable speed with controls.
One (1) California Pellet Mill conditioner for use with a pellet mill. Mixing section measures approximately 28″ in diameter x 8′ long. Unit is belt driven by approximately a 15 HP motor through a gear reducer
One (1) used Champion model 20″ x 44″ Magnum hammer-mill. Unit has 2,400 cubic inches of screen area with a 3/16″ screen installed. 200 HP 1800 RPM motor supplies a 20,730 RPM tip speed. 44″ diameter rotor. Serial number 102396. 460/3/60, 230 amps.
Used Cumberland / Gloucester model 1842i granulator having an 18″ x 42″ feed throat with three (3) knife open rotor. Rotor is belt driven by a 100 HP 1775 RPM 460-volt 134 FLA motor. Two (2) bed knives. Insulated tray feed hopper with 19.5″ x 42″ opening. Insulated body panels. Set up for 6″ OD airveyor discharge. Discharge is via a Sterling model 6005FV blower with a 7.5 HP motor. Includes free standing console type control panel with Alan Bradley Dialog Plus soft starter. Granulator S/N 01703024
Colorado Mill Equipment model C5 pellet cooler (now replaced by the c6). Rated at 3 to 6 tons per hour of pellets depending on pellet size, density, temperature and composition. Unit has a nominal 55″ x 55″ variable swing discharge grid with a dwell time of 10 to15 minutes. Includes optional cyclone with 17″ inlet and 11″ outlet, 15 HP blower, screener, and top airlock with a 10″ x 12″ entrance and 1 HP motor with gearbox. limited use. extremely clean.
Davis Standard model 60IN60TPIH 6″ 30:1 L/D extruder having a six (6) zone electrically heated, water cooled (closed loop) non-vented barrel at a 42″ center-line height. Oversize heavy-duty gearbox has a reduction ratio of 11.29:1 and is rated at 706 HP at a service factor of 1.5. The gearbox is set up for a direct drive from the back of the extruder. Gearbox has an oil pump with heat exchanger for lubrication and cooling. The extruder has a water-cooled feed throat with 6″ wide x 9″ long on center entrance. Air actuated C-clamp with swing away die holder on the discharge. S/N S-4866, Shop order S6300. Manufactured 10/96. Offered less panel, motor and drive
Granutec model TFG2048-100 granulator having a 20″ x 48″ throat opening with tangential cutting chamber. Three (3) knife open rotor is belt driven by a 100 HP 460-volt 1185 RPM motor. Two (2) bed knives. Insulated tray feed hopper with a 21″ x 48″ opening. Granulator and controls are mounted on a base plate with fork lift rails. Set up for a 6″ OD right hand airveyor discharge. Discharge is via a Sterling model 6005FV blower with 5 HP motor and steel reinforced impeller. Blower discharges into a Kongskilde model RC20 cyclone with four (4) bag filter head and material bin. Material bin with gaylord height discharge measures 48″ x 48″ x 127″ tall. Bin has a 53″ straight side with a 24″ 45 degree slope. Granulator S/N 699-3427
Granutec model TFG3636-125 granulator having a 36″ x 36″ feed throat. Tangential cutting chamber with three (3) knife open rotor. Two (2) bed knives. Rotor is belt driven by a 125 HP 460-volt 1185 RPM 146 FLA motor. Tray feed hopper. Granulator and controls are mounted on a base plate with fork lift rails. Discharge is set up for an 8″ right hand airveyor. Discharge is via a Kongskilde model MTD-35 blower with 15 HP motor and steel reinforced impeller. Blower discharges into a Kongskilde model RC40 cyclone with nine (9) bag filter head, Kongskilde RF20 rotary valve, and material holding bin. Bin measures 48″ x 48″ x 127″ tall plus 24″ of 45-degree slope. Bin also has 6″ OD gaylord height discharge, Granulator S/N 1205-4296.
One (1) used Sprout Waldron model 26 pellet mill having a 26″ diameter die with ¼” holes. Unit was recently rebuilt and was used for test runs on wood pellets and alfalfa. 11″ x 13″ feed entrance with 5 HP feeder. Conditioner is mounted over the pellet mill and has a 10 HP drive and discharges into the feed entrance of the mill. Unit is direct driven by a 300 HP A/C motor with Motortronics VMX series soft start. extremely clean. serial number 82-244. 460/3/60 operation.
Davis Standard model 45IN45H 4.5″ 20:1 L/D rubber extruder having a four (4) zone electrically heated, water cooled (closed loop), vented barrel at a 49″ center-line height. Heavy-duty gearbox has a reduction ratio of 17.36:1 and is rated at 300 HP at a service factor of 1.5. Set up for maximum screw speed RPM of 100. The gearbox is direct driven in a tuck under manner by approximately a 150 HP Reliance D/C motor. The extruder has a water-cooled feed throat with power feed for cold feeding rubber. The barrel is vented and a has a vacuum pump mounted on the base. C-clamp with swing away die holder on the discharge. S/N J5585, Shop order 97702C. Manufactured 3/1985. 460/3/60 input.
Davis Standard model 80IN80H 8″ 24:1 L/D extruder having a five (5) zone electrically heated, water cooled (closed loop) barrel at a 42″ center-line height. Oversize heavy-duty gearbox has a reduction ratio of 23.93:1 and is rated at 1080 HP at a service factor of 1.5.Set up for maximum screw speed RPM of 100. The gearbox is direct driven in a wrap-around manner by a 400 HP 1755 RPM Reliance A/C motor with Rockwell Automation inverter and isolation transformer. The extruder has a water-cooled feed throat with 7” wide x 10” long on center entrance. The temperature control panel has five (5) zones for the barrel and eight (8) zones of temperature controls for die zones. C-clamp with swing away die holder on the discharge. Last used on HDPE. Includes three component blending hopper which is driven off of the main gearbox. Spare Barrier screw for the extruder. S/N 77621, Shop order G8739. Manufactured 3/28/2000. Gearbox updated 1/28/2004. 460/3/60 input. Extremely clean.
VECOPLAN MODEL RG52/100SPK SINGLE SHAFT SHREDDER, S/N 8124010, 2005 MODEL YEAR, 15″ DIAMETER ROTOR WITH 60 PC DOUBLE ROW OF BOLT ON 40mm INDEX ABLE CUTTERS, ROTOR IS POWERED BY A 63 KW (85 HP) 480 VOLT MOTOR, HYDRAULIC POWERED RAM, ORIGINAL OEM 480V TOUCH SCREEN CONTROL PANEL, 2″ HOLES SCREEN, INCLUDES 25′ LONG IN-FEED CONVEYOR WITH 41″ WIDE FLAT BELT AND 36″ TALL SIDE WALLS, POWERED BY A 2 HP 460 VOLT MOTOR, ALSO INCLUDES TAKE-AWAY CONVEYOR WITH 16″ WIDE BELT WITH 1.5″ TALL CLEATS 48″ ON CENTER AND IS 153″ TOTAL LENGTH, POWERED BY A 1 HP 460 VOLT MOTOR AND HAS MAGNETIC HEAD PULLEY
SHRED-PAX MODEL AZ-80 TWIN SHAFT SHREDDER, S/N 160-9216. 33″ X 63″ WIDE CUTTING CHAMBER ENTRANCE. CARBON STEEL CONSTRUCTION. TWO (2) ROWS OF INTER-MESHING KNIVES MEASURING 1-3/4″ THICK. EACH SHAFT IS DRIVEN BY A 40 HP 230/460-VOLT 1750 RPM SUMITOMO A/C MOTOR THRU A SM-CYCLO REDUCER. MOUNTED ON A STEEL FRAME. MANUFACTURED 1992. OVERALL DIMENSIONS 149″ X 53″ 94″. OFFERED LESS CONTROLS
4.5″ 30:1 L/D STERLING EXTRUDER HAVING AN ELECTRICALLY HEATED, AIR- COOLED AND SIDE VENTED BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX IS A LUFKIN CHANGE GEAR TYPE AND IS DIRECT DRIVEN DRIVEN IN A TUCK UNDER MANNER BY A 150 HP DC MOTOR WITH SCR. INCLUDES GRAVITY FEED HOPPER. INTEGRAL CONTROL PANEL WITH SIX ZONES OF TEMPERATURE CONTROL, SCR AND PELLETIZER CONTROLS. BERINGER MODEL 17 HYDRAULIC SLIDE PLATE SCREEN CHANGER HAVING TWO (2) NOMINAL 4.5″ DIAMETER BREAKER PLATES IS MOUNTED ON THE EXTRUDER DISCHARGE. INCLUDES TWO HP HYDRAULIC POWER PACK. FOLLOWING THE SCREEN CHANGER IS A BERINGER MODEL WRP12 WATER RING PELLETIZING SYSTEM WITH 3 HP CUTTING HEAD, 45 HOLE DIE, TEMPERED WATER SYSTEM, SLUICE-WAY, AND 2 HP CENTRIFUGAL SPIN DRYER. PULLED FROM SERVICE 1/2020
ONE 4.5″ 30:1 L/D GLOUCESTER EXTRUDER HAVING AN ELECTRICALLY HEATED, NON- COOLED AND SIDE VENTED BARREL WITH TWO HP VACUUM PUMP AT A 42″ CENTER-LINE. GEARBOX IS DRIVEN BY A 300 HP DC MOTOR WITH EMERSON SCR CONTROL. 6” X 13.5” FEED THROAT ENTRANCE. INCLUDES GRAVITY FEED HOPPER. INTEGRAL CONTROL PANEL WITH SIX ZONES OF TEMPERATURE CONTROL, SCR AND PELLETIZER CONTROLS. PRODEX HYDRAULIC SLIDE PLATE SCREEN CHANGER HAVING TWO (2) NOMINAL 4.5″ DIAMETER BREAKER PLATES IS MOUNTED ON THE EXTRUDER DISCHARGE. INCLUDES TWO HP HYDRAULIC POWER PACK. FOLLOWING THE SCREEN CHANGER IS A BERINGER MODEL WRP12 WATER RING PELLETIZING SYSTEM WITH 3-HP CUTTING HEAD, 32 HOLE DIE, TEMPERED WATER SYSTEM, SLUICE-WAY, AND 2 HP CENTRIFUGAL SPIN DRYER. EXTRUDER SCREW REBUILT 12/2019. LAST USED ON PP AT 1300 POUNDS AN HOUR, HIPS AT 1500 POUNDS AN HOUR AND HDPE AT 1100 POUNDS AN HOUR. PULLED FROM SERVICE 1/2020.
ONE (1) USED AUTOMATIK / GALA MODEL SPHERO 220 UNDERWATER PELLETIZING SYSTEM. UNIT IS RATED UP TO 22,000 POUNDS PER HOUR. ORDER NUMBER 1018134. MACHINE NUMBER 1018144-SH-117. MANUFACTURED 2010. 460/3/60. THE SYSTEM CONSISTS OF THE FOLLOWING:
A) HYDRAULICALLY ACTUATED START UP VALUE WITH 11 KW HYDRAULIC PUMP
B) LIQUID HEATED DIE PLATE WITH STERLCO MODEL M2B6017-L 80 KW OIL HEATER
C) 60 HP 36 KNIFE CUTTER HEAD WITH PNEUMATICALLY ADJUSTABLE KNIFE SHAFT
D) CUTTING CHAMBER WITH TANGENTIAL WATER SUPPLY AND PELLET DRAIN
E) MOVITEC MODEL VSF 90/4-2B WATER TEMPERING SYSTEM WITH FUNKE PLATE TYPE HEAT EX-CHANGER
F) 7.5 HP SPIN DRYER WITH AGGLOMERATE CATCHER AND 1.5 HP BLOWER. (MISSING MOTOR)
G) FREE STANDING CONTROL PANEL
H) SUPPORT STRUCTURE FOR CUTTER, CUTTING CHAMBER, HYDRAULIC PUMP, HYDRAULIC VALE AND OPERATOR CONTROLS.
ONE (1) USED GNEUSS MODEL RSF90 GENIUS SCREEN CHANGER, S/N 0113-3506, RATED FOR UP TO 2450 POUNDS AN HOUR. FULLY-AUTOMATIC, 230 VOLTS. MOUNTED ON A STAND. EXTREMELY CLEAN. INCLUDES HYDRAULIC PUMP, MAAG MODEL ES-70/70 MELT PUMP WITH 15 HP DRIVE AND EIGHT ZONE TEMPERATURE CONTROL PANEL. MANUFACTURED IN 2013
NEW SHRED TECH MODEL ST-25ES DUAL SHAFT SHREDDER, S/N ST-25ES-F314, 2019 MODEL YEAR, 16″ X 14″ CUTTING CHAMBER, TWO HEXAGONAL COUNTER ROTATING SHAFTS, 5-7/8 SHAFT CENTER DISTANCE, 20 5/8″ WIDE X 7-3/4 DIAMETER TWO TEETH KNIVES, POWERED BY A 20 HP 480 VOLT GEAR REDUCED MOTOR, 21 RPM FAST SHAFT, 18 RPM SLOW SHAFT, 39,865 LBS MAXIMUM TOOTH FORCE, 31″ FROM FLOOR STAND TO STRADDLE DISCHARGE CUSTOMER SUPPLIED CONTAINER, 27″ X 29″ STANDARD FEED OPENING IN-FEED HOPPER, INCLUDES NEMA RATED CONTROL PANEL WITH PROGRAMMABLE LOGIC CONTROLLER AND FUSED LOCKABLE DISCONNECT