Cumberland model 2050B granulator, S/N 51310-6928, 20″ x 50″ feed throat, 5 knife 130mm steep angle rotor, 2 bed knife, conveyor in-feed hopper, 100 HP 208-230/460-volt 1775 RPM motor, 10″ OD airveyor discharge, mounted to a 36″ tall leg base, starter & controls not included.
Werner & Pfleiderer Model ZSK20 20mm co-rotating twin screw extruder. S/N 02-3108-1000-010-1, Has 40:1 L/D barrel at a 43″ centerline driven through a 16.2:1 gearbox with a 37 newton meter torque capacity per screw shaft, extruder is powered by a 5 HP A/C motor with Allen Bradley 1336 Impact Drive unit, 588 RPM screw speed. Includes Brabender 1/2 HP model MS-FW40/Oplus-70 feeder, spare used motor and gearbox in unknown condition. Extruder manufactured 3/2003
Bay Plastics Machinery strand pelletizer model A12S, S/N A12S972, 12″ wide 48 knife helical rotor is driven by a 15 HP 480-volt motor, pull roll is driven by a 2 HP 480-volt motor, Includes installed 48 knife rotor, spare sharpened A12 Stellite (7.972″) 48 knife helical rotor, a second spare sharpened rotor (unknown OD), two spare knurled lower pull rolls, and two spare upper Hypalon pull rolls, complete with variable speed drives for the rotor and pull rolls
Werner & Pfleiderer Model ZSK40 40mm co-rotating twin screw extruder, S/N 180399, 1990 model year, 46:1 L//D vented barrel with 11 barrel sections and a 41″ centerline. Driven by a 50 HP 500-volt 1750/2100 RPM D/C motor and SCR Control with a screw speed of 517 RPM. Includes Acrison 1.5 HP weight loss differential feeder, 2.2 KW Tervac vacuum pump, and side feeder.
Used Werner & Pfleiderer Model ZSK50 Mega co-rotating twin screw extruder. New in 2000, rebuilt May 2011. Has 1.593:1 gear ratio supplying 1100 RPM screw speed with 815 newton meters per shaft. Includes side feeder, electrically heated water-cooled barrel, Brabender feeder on primary feed throat and auxiliary Brabender feeder on screw side feeder. Includes temperature control panel and driven by an approximate 250 HP D/C motor and drive. Spare parts include (11) new barrel sections, spare side feeder, and spare barrel tie rods
One used 250 cubic foot capacity non-jacketed stainless steel double ribbon blender, S/N 64750-62. Ribbon is chain driven by a Reliance 100 HP 1785 RPM 460-volt 3-phase motor through a gearbox. Trough dimensions are approximately 144″ L x 60″ W x 66″ D and has a center bottom discharge. Overall dimensions of the blender is approximately 186″ L x 67″ W x 107″ H. Mounted on 304 stainless steel legs, includes controls and was last used on food products
One (1) Used 2″ 24’1 Egan extruder having a five (5) zones electrically heated, air cooled, and non-vented barrel at approximately a 50″ centerline height. Extruder is mounted on a mobile cart with casters. If the extruder is removed from the cart it will have a nominal 42″ centerline height. Cone Drive gearbox has a reduction ratio of 10:1 and is rated at 19 HP at a service factor of 1.0. Gearbox is belt driven by a 25 HP D/C motor with an Allen-Bradley model 1395 drive. Unitized temperature control panel has fifteen (15) zones of controllers. C clamp on the barrel discharge. Gravity feed hopper with Conair DB 8 hopper loader on the feed throat. Feed throat entrance is nominal 3″ round. Machine recently updated. Serial number JO 07319-05. 240/3/60 input on the barrel. 460/3/60 on the drive. Several transformers included. Extremely clean. Ideal co-extruder. Approximately 6,000 Lbs.
Rapid model 300-45 granulator, S/N 620.501562.10.1, 10″ x 18″ feed throat, 3 knife open rotor, 2 bed knives mounted in the 2nd and 5th positions, tangential cutting chamber, insulated conveyor in-feed hopper and body panels, 4″ OD left hand airveyor discharge, mounted on vibration control pads. Includes Laros model A-510-18-120 incline conveyor 114″ long x 18″ wide with smooth finish belt and 1″ tall cleats 28.75″ on center. Conveyor has 4″ tall stainless steel side rails, 30″ from floor feed height and matching 65″ granulator discharge height. Conveyor is powered by a 3/8 HP 460-volt motor. Also includes a Sterling model 4001FD 1 HP 230/460-volt discharge blower with aluminum impeller, 4″ OD inlet / outlet and OK100 rolled flange pipe adapters. Blower also includes a sound suppression enclosure. Granulator includes the 460/3/60 starter and controls for granulator, blower, and conveyor. All equipment was manufactured in 2019 and was barely used and are in like new condition.
Cumberland model 1837B granulator, S/N 50510-88009, 18″ x 37″ feed throat, 5 knife high shear rotor, 2 bed knife, 100 HP 460-volt motor, conveyor feed hopper, 8″ right hand airveyor discharge, mounted on 22″ tall plate base, starter and controls not included
One (1) used Gala model 5 underwater pelletizing system, includes 2 HP cutter, two (2) 12-hole dies, one (1) die with nano holes, 20 GPM water system with heater, pump, heater exchanger, 3 HP model 8.1 BF dryer, and free-standing control panel. Also includes four (4) spare cutter assemblies. S/N 85022. very clean.
One (1) used Parkinson 50 series single turret winder able to handle a maximum package of 60″ wide x 42″ diameter on 6″ Tidland air shafts. Each winding shaft is driven by a 7.5 HP A/C motor. Touch screen controls. Includes power indexing, lay-on roll, bow rolls, shaft extraction and doffing cart. Recently pulled from service. Serial number 6-03-4068-01
2020 model year AEC Cumberland model FX1628 granulator, S/N FX1628-20015, 16″ x 28″ feed throat, 3 knife open rotor, 2 bed knife, offset cutting chamber, dual fly wheels, 40 HP 460-volt motor, Insulated conveyor feed hopper and body panels, 6″ left hand airveyor discharge, complete with starter and controls for the granulator and a 5 HP blower, control panel includes amp meter.
Used 16″ Davis Standard Pilot / Laboratory size horizontal sheet/cast line consisting of the following:
(2) 1″ Killion / Davis Standard pedestal style co-extruders each 30:1 L/D driven by 3 HP A/C motors with individual temperature control panels, general purpose 3:1 barrier type screw, air cooled barrels and melt pumps. Includes one (1) spare screw.
(1) 1.25″ Killion / Davis Standard primary 30:1 L/D extruder driven by a 15 HP A/C motor, general purpose 3:1 barrier type screw, individual temperature control panel, gear pump, and air-cooled barrel. Includes four (4) spare screws.
(1) Cloeren Co Ex Block with multiple inserts for co-extrusion. Inserts include AAAAA, BBAAA, CBAAA, AABAA, CAAAB, CCCCC, CBABC, BAAAB, and ABCAA configurations. Manufactured in 2006.
(1) 14″ Cloeren sheet die having a center back entrance but mounted for use in a downward direction. S/N A06-1782-02. Manufactured in 2006
(1) Davis Standard horizontal sheet chill roll stack with three (3) 16″ wide x 24″ OD rolls. With individual motor drive through a gearbox for each roll and built onto frame hydraulic roll loading. Rotary unions for roll cooling/heating with Conair model TC1 stand-alone temperature control. Unit can be run as a cast unit or sheet take-off. With pull rolls.
Also Includes two (2) matt finished rolls, one (1) silicon covered roll and four (4) chrome rolls. Still installed as operated until June 25 2021. New approximately 1995-2006 with laboratory use only.
Cumberland model 2050B granulator, S/N 51310-93014, 20″ x 50″ feed throat, 5 knife steep angle rotor, 2 bed knife, 100 HP 460-volt 1185 RPM motor, OEM style conveyor feed hopper, 10″ airveyor discharge, mounted to a step base, starter and controls not included
Rapid model 2442M granulator, no S/N. 24″ x 42″ feed throat, 5 knife rotor with knife carriers, 3 bed knife, 100 HP 230/460V 1765 RPM motor. Dual flywheel, pneumatic assisted side feed hopper and screen cradle, 8″ airveyor discharge. Mounted on 26″ tall leg base, starter and controls are not included.
One (1) used 1.5″ 20:1 L/D ratio Davis Standard rubber extruder with powered feed roll on throat. Barrel is electrically heated, water cooled (closed loop) and vented at approximately a 42″ centerline height. Includes oil style vacuum pump. C-clamp with die on barrel discharge. Oversize gearbox has a reduction ratio of 17.56:1 and is rated at 50 HP at a service factor of 1.25:1. Gearbox is belt driven by a Marathon Blue Max 25 HP A/C motor with Allen Bradley Power Flex 753 inverter with isolation transformer. Unitized temperature control panel has seven (7) zones of temperature controls. Manufactured January of 2001. Model 150IN20. Shop order number 71118. S/N 16633. 460/3/60 input. 77 FLA.
Davis Standard 1/4″ tubing extrusion line including the following equipment:
A. Davis Standard / Killion model KN-100 1.00″ 24:1 L/D extruder having a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 39″ centerline height. Gearbox is belt driven by a 3 HP D/C motor with SCR control. Unitized temperature control panel has six (6) zones of Eurotherm controllers consisting of three (3) zones for the barrel and three (3) zones for the c-clamp and die. C-clamp is mounted on the discharge. Includes gravity feed hopper. BOM number 05180. 230V/1ph/50-60Hz input, 47 FLA.
B. Nominal ¼” diameter electrically heated tubing die.
C. Davis Standard / Killion medical tubing vacuum tank measuring 116″ long with an 8″ x 8″ cross section. Stainless steel construction. Two glass doors. Upstream and downstream adjustment as well as up and down adjustment. Includes vacuum pump with 3 HP D/C motor, water pumps, sizing fixture, and controls. S/N 30176. 230V/1ph/60Hz input.
D. Davis Standard / Killion belt puller having a 2″ wide belt with 22″ of contact length. Powered by an approximate 1.5 HP D/C motor. Manually actuated top belt. S/N 30174. 230V/3ph/60Hz input, 10 FLA.
Jaeger model RE-900 steel rotating batch blender, 403 cubic foot working capacity, carbon steel construction. Direct driven by a 40 HP motor through a gear reducer. Previously used for batch blending approximately10,000 pounds of plastic with additives.
Leistritz / Gala 27mm compounding line consisting of the following components:
One 27mm 40:1 Leistritz model Micro 27 40GL/40D twin screw extruder with co-rotating inter-meshing screws. Barrel is electrically heated, water cooled and consists of nine (9) barrel sections. Gearbox is direct driven by a 10.5 KW (14.3 HP) DC motor with SCR (silicone controlled rectifier) allowing for an approximate maximum screw speed of 500 RPM. Integral movable control panel has eleven (11) zones of temperature control and all operator controls. Includes pre-polymer metering pump and three (3) sets of screw shafts with loose screw elements. Manufactured in 1997. S/N 2553. Pulled from service in January of 2021. Gala model 6PDV polymer diverter valve with 10 HP hydraulic pump. Unit is used until the extruder is up to speed. Gala model SLC6 underwater pelletizer with 4.3 KW (5.3 HP) spring loaded cutter, model 40TWS water tempering system with heated reservoir, 3 HP water pump, heat exchanger, Gala model 8.1BF spin dryer with agglomerate catcher and free-standing control panel with touch screen controls. Offered less die. Includes spare blades, heater bands, and manuals. 460V/3ph/60Hz 46 FLA operation . Manufactured in 2000. S/N 10100743.