Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17744

    USED DAVIS STANDARD 3.5″ EXTRUDER W/DUAL 1.25″ CO-EXTRUDERS


    Davis Standard straw/tubing co-extrusion extrusion package manufactured 10/2012

    Last used on three color straws extruding two lanes of straws at one time. Extruders and controls are unitized on a single base. 460/3/60 input power. 278 maximum amp load

    A – Davis standard model MV35IN35 3.5” 24:1 L/D extruder having a four (4) zone electrically heated, air cooled, and non-vented barrel at a 42” centerline height. Gearbox has a 17.39:1 reduction ratio and is rated at 257 HP at a service factor of 1.25. Gearbox is belt driven by a 100 HP heavy duty A/C motor with inverter. Extruder presently set up for a maximum screw speed of 100 RPM. integral temperature control panel has ten (10) zones of Davis Standard controllers consisting of four (4) barrel, one (1) screen changer and four (4) die zones. Water cooled feed throat with a 4” x 6” entrance. Barrel is missing one heater band

    B – Mounted on the extruder discharge is an Xaloy model EHC-35 screen changer having two nominal 3.5” diameter breaker plates. S/N EH35-1056

    C – Two (2) incomplete Xaloy melt pumps with 7.5 HP A/C motors and inverters. Missing one (1) motor and one (1) gearbox. Includes free standing control panel

    D – Two (2) used Davis Standard model HPE-125A 1.25” pedestal extruders having electrically heated, air-cooled barrels. Units are height and angle adjustable. Gearbox is a SEW Eurodrive having a 15.19:1 reduction ratio. Each gearbox is direct driven by a Marathon Blue Max 2 HP heavy duty motor. Each extruder has a gravity feed hopper with Conair hopper loader

    E – Two electrically heated straw dies with two co-ex ports on each


    $0.00
  • Array ( [0] => just-arrived [1] => pipe-profile-vac-tanks [2] => just-arrived [3] => pipe-profile-vac-tanks )
  • Stock#: 17743

    USED CONAIR 16 FT DUAL VACUUM SIZING TANK


    One (1) used Conair model VC4N22D 16′ dual vacuum sizing tank. Each tank having a 7″ wide x 12″ high cross section. Clear lids are on a 45 degree angle. Stainless steel construction. Five (5) compartments. One tank is set up for right to left operation while the second tank is set up for left to right operation. With Huestis air stripper mounted on the discharge of each tank. With digital controls. Caster mounted. 460/3/60 input power. Job number 25992-20. Manufactured 2012

    $0.00
  • Array ( [0] => just-arrived [1] => pipe-profile-vac-tanks [2] => just-arrived [3] => pipe-profile-vac-tanks )
  • Stock#: 17742

    USED CONAIR 22 FT VACUUM SIZING TANK


    One (1) used Conair model MT104-22-5 vacuum sizing tank. Good for up to 2″ diameter tubing or profile. Stainless steel construction. Five (5) compartments. 22′ tank length, overall length 285″. 1.75 HP vacuum pump and 2 HP water pump. Clear lids. Internal guide rollers. Set up for right to left operation. With Zumbach thickness gauge with controls and Huestis air stripper. Revision 023699L/010/0304. 230/3/60 input power. Serial number 159983

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17741

    PTI 4000 4″ 30:1 L/D EXTRUDER


    One (1) used 4″ 30:1 L/D ratio PTI model 4000 extruder having a five (5) zone electrically heated, water cooled (closed loop), vented, and plugged barrel at a 53″ center-line height. Flender model E2HA7 gearbox has a reduction ratio of 11.807:1 and is rated at 150 HP. The gearbox is direct driven out the back end by a 150 HP ABB motor with ABB inverter. Gearbox has an oil pump and heat exchanger. The extruder has a water-cooled feed throat with 4″ x 6″ on center entrance. The temperature control panel has five (5) zones for the barrel and fifteen( 15) zones of temperature controls for die zones. Inverter, temperature panel and 5 HP hydraulic power pack for the screen changer are mounted on the sane base as the extruder. Includes Xaloy model EH-45 hydraulic slide plate screen changer, S/N 740. Extruder S/N 4390/1069. Manufactured 2/2007. 460/3/60 input power



    $0.00
  • Array ( [0] => just-arrived [1] => pipe-profile-vac-tanks [2] => just-arrived [3] => pipe-profile-vac-tanks )
  • Stock#: 17740

    USED CONAIR 22 FOOT VACUUM SIZING TANK


    One (1) used Conair model MT104-22-5 vacuum sizing tank. Good for up to 2″ diameter tubing or profile. Stainless steel construction. Five( 5) compartments. 22′ tank length, overall length 285″. 1.75 HP vacuum pump and 2 HP water pump. Clear lids. Internal guide rollers. Set up for right to left operation. Revision 064257L060/1103. 230/3/60 input power. S/N 154786. With Huestis air stripper

    $0.00
  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17657

    USED MITTS & MERRILL MS5025 DUAL SHAFT SHREDDER


    Mitts & Merrill model MS5028 dual shaft shredder. Hydraulic ram assisted. Driven by a 150 HP 460-volt motor via belt drive and thru a gearbox. Gravity discharge. Knives are approximately 1.5″ wide each. Includes control panel and a 48″ wide x 30′ long in-feed conveyor.

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17735

    USED DAVIS STANDARD 3.5″ 34:1 L/D EXTRUDER


    One (1) Used Davis Standard model 35IN35SR 3.5″ extruder, S/N K2191. 34:1 L/D barrel having a seven zone electrically heated and water cooled (closed loop) barrel at a 56″ centerline height. Gearbox has a 5.67:1 reduction ratio and is rated at 158 HP with a service factor of 1.25. Gearbox is belt driven by a 150 HP D/C motor with Control Techniques SCR. Motor was rebuilt in December of 2018. Water cooled feed throat with 4.5″ x 7″ entrance. Integral temperature control panel has thirteen (13) zones of controls. Two instruments are missing. Manufactured 1987. 460-Volt 3-phase 60Hz input power. SO# 99878.

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17730

    USED HPM 3.5″ 24:1 L/D 75 HP EXTRUDER


    HPM model 3.5 TMC-24 3.5″ 24:1 L/D extruder having a four (4) zone electrically heated, air cooled , and non- vented barrel. Gearbox has a reduction ratio of approximately 13.88:1 and is belt driven by a 75 HP brush-less D/C motor with controls. Unitized temperature control panel with seven zones of temperature control. S/N 93182. 460/3/60 input power. Pulled from service 10/2021. Last use on cellulose acetate profiles

    $0.00
  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => just-arrived [3] => 75-hp-granulators )
  • Stock#: 17722

    USED CUMBERLAND 2050B GRANULATOR


    Cumberland model 2050B granulator, S/N 51310-6928, 20″ x 50″ feed throat, 5 knife 130mm steep angle rotor, 2 bed knife, conveyor in-feed hopper, 100 HP 208-230/460-volt 1775 RPM motor, 10″ OD airveyor discharge, mounted to a 36″ tall leg base, starter & controls not included.

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17694

    USED WERNER & PLEIDERER 83mm TWIN SCREW EXTRUDER


    83 mm Werner & Pfleiderer co-rotating twin screw extruder. Has 36/1 L/D barrel, driven by 200 hp dc motor with SCR control. Includes temperature control panel. No side feeder. Serial #136255.

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17702

    USED WERNER & PFLEIDERER ZSK20 TWIN SCREW EXTRUDER


    Werner & Pfleiderer Model ZSK20 20mm co-rotating twin screw extruder. S/N 02-3108-1000-010-1, Has 40:1 L/D barrel at a 43″ centerline driven through a 16.2:1 gearbox with a 37 newton meter torque capacity per screw shaft, extruder is powered by a 5 HP A/C motor with Allen Bradley 1336 Impact Drive unit, 588 RPM screw speed. Includes Brabender 1/2 HP model MS-FW40/Oplus-70 feeder, spare used motor and gearbox in unknown condition. Extruder manufactured 3/2003

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17698

    USED WERNER & PFLEIDERER ZSK40 TWIN SCREW EXTRUDER


    Werner & Pfleiderer Model ZSK40 40mm co-rotating twin screw extruder, S/N 180399, 1990 model year, 46:1 L//D vented barrel with 11 barrel sections and a 41″ centerline. Driven by a 50 HP 500-volt 1750/2100 RPM D/C motor and SCR Control with a screw speed of 517 RPM. Includes Acrison 1.5 HP weight loss differential feeder, 2.2 KW Tervac vacuum pump, and side feeder.

    $0.00
  • Array ( [0] => just-arrived [1] => mixers [2] => just-arrived [3] => mixers )
  • Stock#: 17686

    USED STAINLESS STEEL 250 CUBIC FOOT CAPACITY RIBBON BLENDER


    One used 250 cubic foot capacity non-jacketed stainless steel double ribbon blender, S/N 64750-62. Ribbon is chain driven by a Reliance 100 HP 1785 RPM 460-volt 3-phase motor through a gearbox. Trough dimensions are approximately 144″ L x 60″ W x 66″ D and has a center bottom discharge. Overall dimensions of the blender is approximately 186″ L x 67″ W x 107″ H. Mounted on 304 stainless steel legs, includes controls and was last used on food products

     


    $0.00
  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 17654

    USED EGAN 2″ 24:1 L/D 25 HP EXTRUDER


    One (1) Used 2″ 24’1 Egan extruder having a five (5) zones electrically heated, air cooled, and non-vented barrel at approximately a 50″ centerline height. Extruder is mounted on a mobile cart with casters. If the extruder is removed from the cart it will have a nominal 42″ centerline height. Cone Drive gearbox has a reduction ratio of 10:1 and is rated at 19 HP at a service factor of 1.0. Gearbox is belt driven by a 25 HP D/C motor with an Allen-Bradley model 1395 drive. Unitized temperature control panel has fifteen (15) zones of controllers. C clamp on the barrel discharge. Gravity feed hopper with Conair DB 8 hopper loader on the feed throat. Feed throat entrance is nominal 3″ round. Machine recently updated. Serial number JO 07319-05. 240/3/60 input on the barrel. 460/3/60 on the drive. Several transformers included. Extremely clean. Ideal co-extruder. Approximately 6,000 Lbs.

    $0.00
  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => just-arrived [3] => 75-hp-granulators )
  • Stock#: 17653

    USED CUMBERLAND 1837B GRANULATOR


    Cumberland model 1837B granulator, S/N 50510-88009, 18″ x 37″ feed throat, 5 knife high shear rotor, 2 bed knife, 100 HP 460-volt motor, conveyor feed hopper, 8″ right hand airveyor discharge, mounted on 22″ tall plate base, starter and controls not included

    $0.00
  • Array ( [0] => just-arrived [1] => pelletizers [2] => just-arrived [3] => pelletizers )
  • Stock#: 17545

    USED GALA PELLETIZING SYSTEM


    One (1) used Gala model 5 underwater pelletizing system, includes 2 HP cutter, two (2) 12-hole dies, one (1) die with nano holes, 20 GPM water system with heater, pump, heater exchanger, 3 HP model 8.1 BF dryer, and free-standing control panel. Also includes four (4) spare cutter assemblies. S/N 85022. very clean.

    $0.00
  • Array ( [0] => just-arrived [1] => winders [2] => just-arrived [3] => winders )
  • Stock#: 17622

    USED PARKINSON SERIES 50 WINDER


    One (1) used Parkinson 50 series single turret winder able to handle a maximum package of 60″ wide x 42″ diameter on 6″ Tidland air shafts. Each winding shaft is driven by a 7.5 HP A/C motor. Touch screen controls. Includes power indexing, lay-on roll, bow rolls, shaft extraction and doffing cart. Recently pulled from service. Serial number 6-03-4068-01

    $0.00
  • Array ( [0] => just-arrived [1] => 35-60-hp-granulators [2] => just-arrived [3] => 35-60-hp-granulators )
  • Stock#: 17606

    USED CUMBERLAND FX1628 GRANULATOR


    2020 model year AEC Cumberland model FX1628 granulator, S/N FX1628-20015, 16″ x 28″ feed throat, 3 knife open rotor, 2 bed knife, offset cutting chamber, dual fly wheels, 40 HP 460-volt motor, Insulated conveyor feed hopper and body panels, 6″ left hand airveyor discharge, complete with starter and controls for the granulator and a 5 HP blower, control panel includes amp meter.

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => extrusion-sheet-dies [3] => lab-testing-equipment [4] => just-arrived [5] => extruders-34-3 [6] => extrusion-sheet-dies [7] => lab-testing-equipment )
  • Stock#: 17556

    USED DAVIS / KILLION LAB SHEET / CAST EXTRUSION LINE


    Used 16″ Davis Standard Pilot / Laboratory size horizontal sheet/cast line consisting of the following:

    (2) 1″ Killion / Davis Standard pedestal style co-extruders each 30:1 L/D driven by 3 HP A/C motors with individual temperature control panels, general purpose 3:1 barrier type screw, air cooled barrels and melt pumps. Includes one (1) spare screw.

    (1) 1.25″ Killion / Davis Standard primary 30:1 L/D extruder driven by a 15 HP A/C motor, general purpose 3:1 barrier type screw, individual temperature control panel, gear pump, and air-cooled barrel. Includes four (4) spare screws.

    (1) Cloeren Co Ex Block with multiple inserts for co-extrusion. Inserts include AAAAA, BBAAA, CBAAA, AABAA, CAAAB, CCCCC, CBABC, BAAAB, and ABCAA configurations. Manufactured in 2006.

    (1) 14″ Cloeren sheet die having a center back entrance but mounted for use in a downward direction. S/N A06-1782-02. Manufactured in 2006

    (1) Davis Standard horizontal sheet chill roll stack with three (3) 16″ wide x 24″ OD rolls. With individual motor drive through a gearbox for each roll and built onto frame hydraulic roll loading. Rotary unions for roll cooling/heating with Conair model TC1 stand-alone temperature control. Unit can be run as a cast unit or sheet take-off. With pull rolls.

    Also Includes two (2) matt finished rolls, one (1) silicon covered roll and four (4) chrome rolls. Still installed as operated until June 25 2021. New approximately 1995-2006 with laboratory use only.

    $0.00
  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => just-arrived [3] => 75-hp-granulators )
  • Stock#: 17505

    USED RAPID 2442M GRANULATOR


    Rapid model 2442M granulator, no S/N. 24″ x 42″ feed throat, 5 knife rotor with knife carriers, 3 bed knife, 100 HP 230/460V 1765 RPM motor. Dual flywheel, pneumatic assisted side feed hopper and screen cradle, 8″ airveyor discharge. Mounted on 26″ tall leg base, starter and controls are not included.

    $0.00