Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17064

    USED BERSTORFF 25MM TWIN SCREW EXTRUDER


    BERSTORFF 25MM TWIN SCREW EXTRUDER, TYPE ZE25. CO-ROTATING SIDE BY SIDE SCREW DESIGN. 36:1 L/D RATIO. ELECTRICALLY HEATED, AIR COOLED, BARREL CONSISTING OF EIGHT SECTIONS INCLUDING FEED THROAT, 42” BARREL CENTER LINE HEIGHT, SIDE FEEDER ENTRANCE AND VENT SECTION. ACCURATE FEEDER MOUNTED ON FEED THROAT AND K-TRON FEEDER FOR SIDE FEEDER. 15 HP DC MOTOR WITH SCR. CONSOLE TYPE CONTROL PANEL WITH SEVEN (7) ZONES OF TEMPERATURE CONTROL, OPERATOR CONTROLS AND FEEDER CONTROLS INCLUDED. MANUFACTURED 1994. 240-VOLT INPUT POWER.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17041

    USED DAVIS STANDARD 3.5″ 100 HP EXTRUDER


    USED DAVIS STANDARD MARK V MODEL MV35IN35 3.5″ 30:1 L/D EXTRUDER HAVING A FIVE (5) ZONE ELECTRICALLY HEATED, AIR COOLED BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A 17.39 REDUCTION RATIO AND IS RATED AT 158 HP AT A SERVICE FACTOR OF 1.25. GEARBOX IS BELT DRIVEN BY A 100 HP AC MOTOR WITH AN ALAN BRADLEY INVERTER. TEMPERATURE CONTROL PANEL HAS NINE (9) ZONES OF CONTROLLERS. WATER COOLED FEED THROAT. EXTRUDER, CONTROL PANEL, AND MOTOR ARE ALL UNITIZED ON A SINGLE BASE. S/N 72974, SO# AB506. MFD 2001. 460/3/60

  • Array ( [0] => just-arrived [1] => feed-paddle-roll-granulators [2] => just-arrived [3] => feed-paddle-roll-granulators )
  • Stock#: 17046

    USED TRIA TRK5030 FEED ROLL GRANULATOR


    TRIA MODEL TRK5030 FEED ROLL IN-FEED ONLY GRANULATOR, S/N 33219814, MANUFACTURED IN 2016, 11.8″ X 19.7″ WATER COOLED CUTTING CHAMBER, 15″ WIDE X 3″ DIAMETER KNURLED STEEL FEED ROLLS WITH BRASS SCRAPER, PNEUMATIC PINCH, AND WITH A LINE SPEED OF UP TO 65 FEET PER MINUTE, GRANULATOR HAS 3 KNIFE OPEN ROTOR, 2 BED KNIVES, AND IS POWERED BY A 10 HP 460 VOLT MOTOR, 4″ OD LEFT HAND AIRVEYOR DISCHARGE, 13/32″ HOLES SCREEN, COMPLETE WITH 3 HP BLOWER MODEL HT40SL AND CYCLONE MODEL AV400 MOUNTED TO A DEDICATED STAND, CYCLONE HAS A 4″ INLET AND OUTLET, GRANULATOR IS COMPLETE WITH VIBRATION CONTROL MOUNTING PADS, SOUND SUPPRESSION CABINET, KNIFE SETTING FIXTURE, STARTER AND CONTROLS FOR GRANULATOR, BLOWER, AND V/S DRIVE FOR THE FEED ROLLS.

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17048

    USED VECOPLAN V-ECO 1300 SHREDDER SYSTEM


    VECOPLAN MODEL V-ECO 1300 SHREDDER, S/N 12489 010, MANUFACTURED 2-12-15, 135 CUTTERS, (2) BED KNIFE POSITIONS – (1) ADJUSTABLE, 150 HP 460 VOLT MOTOR, ½” SCREEN – HAS 3/8″ SCREEN IN MACHINE, 3959 HOURS ON MACHINE, INCLUDES 35′ CONVEYOR, 3 HP DRIVE W/ BIG GEAR BOX – 43″ WIDE BELT – 2″ CLEATS ON 32″CENTERS, HOME MADE CUSTOM DEBRIS GUARD ENCLOSURE OVER THE TOTAL TOP OF THE SHREDDERS’ HOPPER “SEE PICTURE”, S & S METAL DETECTOR WITH 12″ HIGH CLEARANCE ABOVE BELT INCLUDES 6′ NONMAGNETIC SECTION BELOW BELTING, CUSTOM BUILT DROP OUT CHUTE POSITIONED BEFORE THE SHREDDER HOPPER TO CLEAN MATERIAL WITH METAL OFF CONVEYOR AND INTO BIN ON FLOOR, KICE 15 HP BLOWER WITH 8″ OUTLET TUBING RUNNING OVER TO 48″ DIAMETER CYCLONE RECEIVER THAT IS 7′ TALL. THE CYCLONE HAS “6” FILTER BAGS THAT HANG DOWN 8′. THE GAYLORD FILL DISCHARGE HAS A DRAWER MAGNET WITH RARE EARTH MAGNET BARS. WAS PROCESSING POST-CONSUMER JUGS & BOTTLES/POST-INDUSTRIAL SCRAP @ 3,000 LBS/HR, 90% POST-CONSUMER – 10% POST INDUSTRIAL

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17023

    USED FITZPATRICK DASO 6 FITZMILL


    USED FITZPATRICK DASO 6 FITZMILL. S/N 11303, STAINLESS STEEL CONSTRUCTION. UNIT FED BY K-TRON MODEL K-2 VOLUMETRIC FEEDER. FIXED KNIFE ROTOR. ROTOR IS BELT DRIVEN BY 7.5 HP MOTOR WITH EXPLOSION PROOF CONTROLS. MOUNTED ON A STAND WITH CASTERS ALLOWING FOR A DRUM HEIGHT DISCHARGE. INCLUDES STARTER AND CONTROLS FOR FEEDER AND FITZMILL. 460/3/60. S/O NUMBER 8627

  • Array ( [0] => just-arrived [1] => just-arrived )
  • Stock#: 17015

    USED ACRISON WEIGH SCALE BATCH FEEDER


    ACRISON MODEL A405-80-50-V101-E WEIGH SCALE BATCH MATERIAL FEEDER, S/N 91265-01, MD-II WEIGH FEEDER CONTROLLER WITH TOUCH-PAD CONTROLS, USED AS A COLLEGE TRAINING UNIT, STAINLESS STEEL BATCH HOPPER, AUGER SCREW IS POWERED BY A .5 HP 90 VOLT D/C 1725 RPM D/C MOTOR, INCLUDES INSTALLED SCREW, SPARE SCREW, AND 1.75″, 2″, AND 2-3/8″ FEEDER TUBES, CAN INSTALL UP TO A 2-11/16″ SCREW, OVERALL DIMENSIONS MOUNTED TO INCLUDED CASTER CART IS 33″ X 28″ X 83″, EXCELLENT CONDITION, ALSO INCLUDES OEM MANUAL

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-lines [3] => just-arrived [4] => pelletizers [5] => pelletizing-lines )
  • Stock#: 17001

    USED AUTOMATIK / GALA MODEL SPHERO 220 UNDERWATER PELLETIZING SYSTEM


    ONE (1) USED AUTOMATIK / GALA MODEL SPHERO 220 UNDERWATER PELLETIZING SYSTEM. UNIT IS RATED UP TO 22,000 POUNDS PER HOUR. ORDER NUMBER 1018134. MACHINE NUMBER 1018144-SH-117. MANUFACTURED 2010. 460/3/60. THE SYSTEM CONSISTS OF THE FOLLOWING:

    A) HYDRAULICALLY ACTUATED START UP VALUE WITH 11 KW HYDRAULIC PUMP

    B) LIQUID HEATED DIE PLATE WITH STERLCO MODEL M2B6017-L 80 KW OIL HEATER

    C) 60 HP 36 KNIFE CUTTER HEAD WITH PNEUMATICALLY ADJUSTABLE KNIFE SHAFT

    D) CUTTING CHAMBER WITH TANGENTIAL WATER SUPPLY AND PELLET DRAIN

    E) MOVITEC MODEL VSF 90/4-2B WATER TEMPERING SYSTEM WITH FUNKE PLATE TYPE HEAT EX-CHANGER

    F) 7.5 HP SPIN DRYER WITH AGGLOMERATE CATCHER AND 1.5 HP BLOWER. (MISSING MOTOR)

    G) FREE STANDING CONTROL PANEL

    H) SUPPORT STRUCTURE FOR CUTTER, CUTTING CHAMBER, HYDRAULIC PUMP, HYDRAULIC VALE AND OPERATOR CONTROLS.

    LAST USED ON EPS MICRO BEADS

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-lines [3] => just-arrived [4] => pelletizers [5] => pelletizing-lines )
  • Stock#: 17002

    USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM


    ONE (1) USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM. UNIT IS RATED FOR UP TO 22,000 POUNDS PER HOUR. ORDER NUMBER 1019020. MACHINE NUMBER SH-204. MANUFACTURED 2013. 460/3/60. THE SYSTEM CONSISTS OF THE FOLLOWING:

    A) HYDRAULICALLY ACTUATED START UP VALUE WITH 11 KW HYDRAULIC PUMP

    B) LIQUID HEATED DIE PLATE WITH STERLCO MODEL M2B6017-L 100 KW OIL HEATER

    C) 60 HP 36 KNIFE CUTTER HEAD WITH PNEUMATICALLY ADJUSTABLE KNIFE SHAFT

    D) CUTTING CHAMBER WITH TANGENTIAL WATER SUPPLY AND PELLET DRAIN

    E) MOVITEC MODEL VSF 90/4-2B WATER TEMPERING SYSTEM WITH FUNKE PLATE TYPE HEAT EX-CHANGER

    F) 7.5 HP SPIN DRYER WITH AGGLOMERATE CATCHER AND 1.5 HP BLOWER

    G) FREE STANDING CONTROL PANEL

    H) SUPPORT STRUCTURE FOR CUTTER, CUTTING CHAMBER, HYDRAULIC PUMP, HYDRAULIC VALE AND OPERATOR CONTROLS.

    LAST USED ON EPS MICRO BEADS.

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-lines [3] => just-arrived [4] => pelletizers [5] => pelletizing-lines )
  • Stock#: 17003

    USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM


    ONE (1) USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM. UNIT IS RATED UP TO 22,000 POUNDS PER HOUR. ORDER NUMBER 1019020. MACHINE NUMBER SH-205. MANUFACTURED 2013. 460/3/60. THE SYSTEM CONSISTS OF THE FOLLOWING:

    A) HYDRAULICALLY ACTUATED START UP VALUE WITH 11 KW HYDRAULIC PUMP

    B) LIQUID HEATED DIE PLATE WITH STERLCO MODEL M2B6017-L 100 KW OIL HEATER

    C) 60 HP 36 KNIFE CUTTER HEAD WITH PNEUMATICALLY ADJUSTABLE KNIFE SHAFT

    D) CUTTING CHAMBER WITH TANGENTIAL WATER SUPPLY AND PELLET DRAIN

    E) MOVITEC MODEL VSF 90/4-2B WATER TEMPERING SYSTEM WITH FUNKE PLATE TYPE HEAT EX-CHANGER

    F) 7.5 HP SPIN DRYER WITH AGGLOMERATE CATCHER AND 1.5 HP BLOWER

    G) FREE STANDING CONTROL PANEL

    H) SUPPORT STRUCTURE FOR CUTTER, CUTTING CHAMBER, HYDRAULIC PUMP, HYDRAULIC VALE AND OPERATOR CONTROLS

    LAST USED ON EPS MICRO BEADS

  • Array ( [0] => just-arrived [1] => extrusion-screen-changers [2] => just-arrived [3] => extrusion-screen-changers )
  • Stock#: 17004

    USED GNEUSS RSF90 GENIUS SCREEN CHANGER


    ONE (1) USED GNEUSS MODEL RSF90 GENIUS SCREEN CHANGER, S/N 0113-3506, RATED FOR UP TO 2450 POUNDS AN HOUR. FULLY-AUTOMATIC, 230 VOLTS. MOUNTED ON A STAND. EXTREMELY CLEAN. INCLUDES HYDRAULIC PUMP, MAAG MODEL ES-70/70 MELT PUMP WITH 15 HP DRIVE AND EIGHT ZONE TEMPERATURE CONTROL PANEL. MANUFACTURED IN 2013

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17012

    USED PROCEDYNE PCF2430-FB THERMAL PART CLEANING SYSTEM


    ONE (1) USED PROCEDYNE MODEL PCF2430-FB THERMAL PART CLEANING SYSTEM. S/N 1827-00255, 24” X 30” BASKET FOR PARTS. CLEANING SYSTEMS IS DESIGNED TO REMOVE COATINGS FROM ALL TYPES OF HARDWARE AND PARTS – WITH NO CARBON RESIDUE. ABSOLUTE TEMPERATURE CONTROL AND THERMAL UNIFORMITY PERMITS CLEANING OF COMPLEX CRITICAL HARDWARE WITH MINIMAL RISK OF DISTORTION OR METALLURGICAL DAMAGE.  NATURAL GAS FIRED 400,000 BTU BURNER. WITH CONTROLS, CYCLONE AND OPTIONAL PROCEDYNE MODEL AB-25-1 AFTERBURNER, S/N 1627-00255, 120 VOLT SINGLE PHASE OPERATION, AFTERBURNER CAPACITY IS 15 LBS PER HOUR AT PEAK RATE

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 16964

    NEW SHRED TECH ST-25ES DUAL SHAFT SHREDDER


    NEW SHRED TECH MODEL ST-25ES DUAL SHAFT SHREDDER, S/N ST-25ES-F314, 2019 MODEL YEAR, 16″ X 14″ CUTTING CHAMBER, TWO HEXAGONAL COUNTER ROTATING SHAFTS, 5-7/8 SHAFT CENTER DISTANCE, 20 5/8″ WIDE X 7-3/4 DIAMETER TWO TEETH KNIVES, POWERED BY A 20 HP 480 VOLT GEAR REDUCED MOTOR, 21 RPM FAST SHAFT, 18 RPM SLOW SHAFT, 39,865 LBS MAXIMUM TOOTH FORCE, 31″ FROM FLOOR STAND TO STRADDLE DISCHARGE CUSTOMER SUPPLIED CONTAINER, 27″ X 29″ STANDARD FEED OPENING IN-FEED HOPPER, INCLUDES NEMA RATED CONTROL PANEL WITH PROGRAMMABLE LOGIC CONTROLLER AND FUSED LOCKABLE DISCONNECT

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16967

    USED DAVIS STANDARD 45IN45H 4.5″ EXTRUDER


    USED 4.5″ DAVIS STANDARD MODEL 45IN45H EXTRUDER, S/N Z4431, S/O 74061, 30:1 L/D VENTED AND ELECTRICALLY HEATED AIR-COOLED BARREL AT 42″ CENTER LINE HEIGHT, DRIVEN BY 200 HP AC MOTOR WITH VARIABLE FREQUENCY DRIVE. INCLUDES TEMPERATURE CONTROL PANEL BUT NO TEMPERATURE INSTRUMENTS OR HMI FOR INFORMATION INPUT. 365 HP RATED GEARBOX WITH 1.5 SERVICE FACTOR AND 17.49:1 GEAR RATIO, MANUFACTURED 12/2001. INCLUDES 4.5″ DYNISCO MODEL EH-45 SCREEN CHANGER WITH HYDRAULIC PUMPING SYSTEM, S/N EH45208

  • Array ( [0] => just-arrived [1] => high-intensity-mixers [2] => just-arrived [3] => high-intensity-mixers )
  • Stock#: 16966

    USED HENSCHEL FM500F 500 LITER HIGH INTENSITY MIXER


    USED 500-LITER HENSCHEL MODEL FM500F HIGH INTENSITY MIXER, S/N 831769, MANUFACTURED 1980, DRIVEN BY 83/110 KW (107/143 HP) 550-VOLT 3 PHASE 60 HERTZ MOTOR. INCLUDES 2-SPEED STARTER AND OPERATOR CONTROLS. HAS 3-TIER BLADES DESIGN, JACKETED BOWL, AND INCLUDES DEFLECTOR BLADE MOUNTED IN MIXER LID. MIXER INCLUDES AIR ACTUATED DISCHARGE AND CLAMPED SWING-AWAY LID

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => extrusion-roll-stacks-rolls [3] => extrusion-sheet-lines [4] => just-arrived [5] => extruders-3-5-10 [6] => extrusion-roll-stacks-rolls [7] => extrusion-sheet-lines )
  • Stock#: 16932

    USED PTI 78″ SHEET LINE


    USED PTI 78″ WIDE SHEET LINE (2003) LAST USED ON PET SHEET

    A – PTI MODEL 6000 6″ 36:1 L/D EXTRUDER HAVING AN EIGHT (8) ZONE ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP) AND VENTED BARREL AT A 64″ CENTER-LINE HEIGHT. GEARBOX IS A FLENDER MODEL SZNF 390, HAS A 15.4:1 REDUCTION RATIO RATED FOR UP TO 986 HP. GEARBOX IS DIRECTLY DRIVEN BY A 500 HP DC MOTOR. OFFERED LESS SCR CONTROL. SCREW IS DESIGNED FOR USE ON PET AND HAS PROVISION FOR COOLING. CONTROL PANEL HAS 25 ZONES OF EUROTHERM CONTROLLERS. SERIAL NUMBER 3767/10082. MANUFACTURED 6/2003

    B – DYNISCO MODEL EH-60 SCREEN CHANGER HAVING TWO NOMINAL 6″ DIAMETER BREAKER PLATES. INCLUDES 2 HP HYDRAULIC POWER PACK.

    C – MAAG MODEL 90/90 MELT PUMP WITH 30 HP DRIVE SYSTEM, CONTROLS, AND MODEL 6000 STATIC MIXER.

    D – CLOEREN 70″ AUTO-FLEX SHEET DIE. 1″ X 4″ BACK CENTER FEED ENTRANCE. SERIAL NUMBER 77831-2129. MANUFACTURED 4/2003.

    E – PTI MODEL 7824 DOWN STACK ROLL STAND HAVING THREE ROLLS MOUNTED IN A VERTICAL ARRANGEMENT CONSISTING OF 24″ DIAMETER MIDDLE AND BOTTOM CHROME PLATED ROLLS AND AN A 16″ DIAMETER CHROME PLATED TOP ROLL. HYDRAULICALLY ACTUATED GAPPING. ROLLS ARE DRIVEN BY A 10 HP AC MOTOR THROUGH GEARBOXES VIA SILENT CHAIN AND SPROCKETS. INCLUDES BUILT ONTO FRAME TEMPERATURE CONTROL SYSTEM (MISSING ONE PUMP), IDLER CONVEYOR, DIP COATING STATION, SLITTING STATION, AND PULL ROLL STAND WITH 78″ X 8″ DIAMETER ROLLS. SERIAL NUMBER 3354R. 480/3/60. 175 AMPS.

    F – 78″ PARKINSON TURRET WINDER HAVING FOUR WINDING POSITIONS. EACH STATION IS DRIVEN BY A 5 HP AC MOTOR. INCLUDES THREE WINDING SHAFTS. MISSING GEARBOX ON TURRET.

    G – PREVIOUSLY RUNNING PET. LINE WAS ORIGINALLY FACTORY DESIGNED TO RUN PET, PP, AND PS AT 2500-3000 POUNDS AN HOUR.

    MORE PICTURES AVAILABLE ON REQUEST

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 16963

    USED SSI M100E(63) DUAL SHAFT SHREDDER


    SSI MODEL M100E(63) DUAL-SHEAR TWO SHAFT SHREDDER, S/N S2175, SHREDDER IS EQUIPPED WITH 41″ X 63″ FEED OPENING AND DRIVEN BY 300 HP 1187 RPM 460 VOLT MOTOR. INCLUDES BREVINI GEAR DRIVE WITH A 29.3:1 REDUCTION RATIO. CUTTERS ARE 530MM DIAMETER (20.9″) AND MADE OF 4140 HT STEEL, DUAL SHAFTS WITH A 188MM (7.4″) SHAFT DIAMETER. CUTTERS ARE OF AN APPROXIMATE 9 TIP DESIGN. OFFERED LESS DRIVE UNIT OR WITH NEW WEG ELECTRIC 300 HP VARIABLE SPEED DRIVE IN NEMA 12 ENCLOSURE WITH DISCONNECT.

  • Array ( [0] => just-arrived [1] => balers [2] => just-arrived [3] => balers )
  • Stock#: 16942

    USED BALEMASTER 360-A HORIZONTAL BALER


    BALEMASTER MODEL 360-A HORIZONTAL CLOSED END BALER, S/N B0221-04-801001, 60″ X 30″ X 42″ BALE SIZE, POWERED BY A 20 HP 3 PHASE MOTOR, 41 FULL AMP LOAD, 6″ HYDRAULIC EJECTION DOOR CYLINDER, 48″ X 35″ HOPPER OPENING, OVERALL DIMENSIONS ARE 190″ X 48″ X 82.25″, APPROXIMATELY 10,000 LBS EMPTY

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16914

    USED MERRITT / DAVIS 3.5″ 24:1 L/D EXTRUDER


    USED 3.5” 24:1 L/D MERRITT-DAVIS STANDARD EXTRUDER HAVING A FIVE (5) ZONE ELECTRICALLY HEATED, AIR COOLED BARREL AND NON VENTED BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A REDUCTION RATIO OF 26.25:1 AND IS SET UP FOR A BELT DRIVE MOTOR. ON CENTER WATER COOLED FEED THROAT. UNITIZED TEMPERATURE CONTROL PANEL FOR SEVEN (7) CONTROLLERS (ONE MISSING).  C CLAMP ON DISCHARGE. UNIT PRESENTLY OFFERED WITHOUT, SCREW, MOTOR, AND SCR DRIVE, MANUFACTURED IN 2001. S/N PR-03729-01

    OR

    MERRITT-DAVIS STANDARD 3.5” 24:1 L/D EXTRUDER HAVING A FIVE (5) ZONE ELECTRICALLY HEATED AIR-COOLED BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A REDUCTION RATIO OF 26.25:1 FOR A SCREW SPEED OF 67 RPM. 100 HP BELT DRIVE MOTOR . ON CENTER WATER COOLED FEED THROAT. UNITIZED TEMPERATURE CONTROL PANEL FOR SEVEN (7) CONTROLLERS.  C CLAMP ON DISCHARGE. INCLUDES SCREW AND SCR MOTOR DRIVE, MANUFACTURED IN 2001. S/N PR-03729-01, UNIT GONE THROUGH AND IN RUNNING ORDER


  • Array ( [0] => just-arrived [1] => pulverizers [2] => just-arrived [3] => pulverizers )
  • Stock#: 16912

    USED PALLMANN PB8 PULVERIZER


    PALLMANN MODEL PP8 PULVERIZING SYSTEM.  ROTORS ON PULVERIZER MEASURE 31.2″ (800 MM) IN DIAMETER WITH DOUBLE CONE IMPELLER FOR PULVERIZING OF PLASTICS. INCLUDES (2) DRIVE MOTORS 35 HP AND 75 HP.  CARBON STEEL, WATER COOLED CHAMBER. PACKAGE INCLUDES ERIEZ MODEL D STYLE 26 FEEDER, 20 HP BLOWER WITH 7” INLET AND 10” OUTLET, 33.5” LONG CYCLONE WITH 6” BOLT ENTRANCE AND ROTARY VALVE ON DISCHARGE, 98” LONG CYCLONE WITH 10” INLET, 30” SWECO SCREENER AND CONTROL PANEL

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16839

    USED AET 6″ 24:’ L/D 300 HP EXTRUDER


    AET MODEL 60ASLT24 6″ 24:1 L/D EXTRUDER HAVING A SEVEN (7) ZONE ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP) BARREL AT A 45″ CENTER-LINE HEIGHT. GEARBOX IS A KOELLMANN MODEL UNEX 8.12 , HAS A REDUCTION RATIO OF 20.07:1 AND IS RATED AT 400 HP AT A SERVICE FACTOR OF 1.6. GEARBOX IS DIRECT DRIVEN OUT THE BACK BY A 300 HP 1755 RPM ABB AC MOTOR WITH INVERTER. WATER COOLED FEED THROAT WITH 7″ WIDE X 10″ LONG ON CENTER ENTRANCE. TEMPERATURE CONTROL PANEL WITH FOURTEEN ZONES. S/N E2355. MANUFACTURED 1/28/04. 460/3/60 INPUT