Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 16620

    USED STEER ENGINEERING 12mm TWIN SCREW EXTRUDER


    STEER ENGINEERING PHARMACEUTICAL TWIN-SCREW EXTRUDER, S/N EA00427, MODEL OMICRON 12P, NEW 2014. SCREW DIAMETER IS 12 MM, DIAMETER RATIO (DO/DI) IS 1.45, FLIGHT DEPTH IS 1.9, MAX SCREW SPEED IS 900 RPM, 2HP DRIVE, 3/60/480V

  • Array ( [0] => just-arrived [1] => blenders [2] => just-arrived [3] => blenders )
  • Stock#: 16815

    USED PATTERSON THORO BLENDER SYSTEM


    PATTERSON INDUSTRIES 18″ DIAMETER JACKETED THORO BLENDER SYSTEM, S/N 412130-CA11, MAXIMUM WATER PRESSURE IS 125 PSI AT 275 DEGREES, MINIMUM DESIGN METAL TEMPERATURE 32 DEGREES AT 125 PSIG, INCLUDES DELTA THERMAL SYSTEMS MODEL KD331S 12,000 WATT OIL HEATER, S/N 17040, WITH CAGE AND EXHAUST HOOD, ALSO INCLUDES BAUER MODEL DP2.5 AIR COMPRESSOR, 13.5 CFM, 200 PSIG, POWERED BY A 5 HP 480 RPM 230/460 VOLT MOTOR

  • Array ( [0] => just-arrived [1] => mixers [2] => ribbon-blenders [3] => just-arrived [4] => mixers [5] => ribbon-blenders )
  • Stock#: 16783

    USED 40 CUBIC FOOT DOUBLE RIBBON MIXER


    USED APPROXIMATELY 40 CUBIC FOOT WORKING CAPACITY STAINLESS STEEL DOUBLE RIBBON BLENDER, JACKETED CHAMBER. HAS 3-PIECE COVER, AIR CYLINDER ACTUATED CENTER BOTTOM DISCHARGE. NO MIXER STAND INCLUDED. CURRENTLY MOUNTED ON LEGS SUPPLYING APPROXIMATELY 6″ DISCHARGE HEIGHT. MIXER IS CHAIN AND SPROCKET DRIVEN, APPROXIMATELY 10 HP GEAR HEAD MOTOR SUPPLYING 155 RPM OUTPUT. HAS 6″ DIAMETER PINION, 24″ DIAMETER BULL GEAR

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => extrusion-sheet-lines [3] => just-arrived [4] => extruders-3-5-10 [5] => extrusion-sheet-lines )
  • Stock#: 16744

    USED CROWN 4.5″ EXTRUSION SHEET LINE


    A) 4.5″ 32:1 L/D RATIO EXTRUDER HAVING A SEVEN (7) ZONE ELECTRICALLY HEATED, AIR COOLED, AND VENTED BARREL AT A 64″ CENTER-LINE HEIGHT. GEARBOX HAS A REDUCTION RATIO OF 18:1 AND IS DIRECT DRIVEN IN A TUCK UNDER MANNER BY A 250 HP BALDOR AC MOTOR WITH ABB ACS800 INVERTER. TEMPERATURE CONTROL PANEL WITH 7 BARREL ZONES AND 11 DOWNSTREAM ZONES OF EURO-THERM MODEL 3216 TEMPERATURE CONTROLLERS.

    B) 4.5″ BERINGER MODEL SC4 HYDRAULIC SLIDE PATE SCREEN CHANGER WITH HYDRAULIC POWER PACK.

    C) MAAG MODEL EXTREX 70 MELT PUMP WITH 15 HP AC MOTOR. DRIVE IS INTEGRATED INTO EXTRUDER PANEL, S/N 50138190-10.

    D) 48″ WIDE FLEX LIP DIE MOUNTED ON A STAND

    E) 64″ WIDE COOLING AND POLISHING STAND HAVING A 16″ DIAMETER TOP ROLL, 24″ DIAMETER MIDDLE AND BOTTOM ROLL MOUNTED IN A VERTICAL ARRANGEMENT FOR DOWN-STACK OPERATION. ROLLS ARE DRIVEN VIA SILENT CHANGE A BY 5 HP DC MOTOR. ROLLS ARE AIR ACTUATED. INCLUDES DIP TANK, IDLER ROLL CONVEYOR, 64″ WIDE PULL ROLLS WITH BY 5 HP DC MOTOR AND TEMP CONTROL SYSTEM WITH 7.5 HP PUMPS AND BUILT ONTO FRAME CONTROLS.

    F) HOBBS SINGLE TURRET 2-POSITION WINDER ABLE TO HANDLE UP TO TO 36″ DIAMETER PACKAGES ON 3″ AIR SHAFTS.

  • Array ( [0] => just-arrived [1] => hog-granulators [2] => just-arrived [3] => hog-granulators )
  • Stock#: 16743

    USED RAPID 2442RS GRANULATOR


    RAPID MODEL 2442RS GRANULATOR, S/N 96588-10.1, 24″ X 42″ FEED THROAT, 20 KNIFE 24MM BOLT STAGGERED HOG ROTOR, 3 BED KNIFE, 100 HP 460 VOLT MOTOR, DUAL FLY-WHEELS, PNEUMATIC TILT BACK ASSIST CONVEYOR FEED HOPPER, PNEUMATIC ASSIST DROP DOWN SCREEN CRADLE, 8″ OD AIRVEYOR DISCHARGE, FRAME BASE, STARTER AND CONTROLS NOT INCLUDED

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 16355

    USED WAYNE 1.250″ 30:1 L/D EXTRUDER


    USED WAYNE 1.25″ EXTRUDER, S/N 9414-832, 30:1 L/D, ELECTRICALLY HEATED AIR COOLED VENTED (PLUGGED) BARREL, DRIVEN BY A 7.5 HP D/C MOTOR WITH SCR CONTROL, 230 VOLT INPUT POWER, TRACK WHEEL BASE, INCLUDES SPARE SCREW

  • Array ( [0] => just-arrived [1] => extrusion-roll-stacks-rolls [2] => just-arrived [3] => extrusion-roll-stacks-rolls )
  • Stock#: 14917

    USED DAVIS STANDARD 52″ WIDE 3 ROLL STACK


    USED DAVIS STANDARD MODEL EXEMPLAR COOLING AND POLISHING STAND HAVING THREE 52″ FACE CHROME PLATED ROLLS MOUNTED IN A VERTICAL ARRANGEMENT FOR DOWNSTACK OPERATION. THE TOP ROLL MEASURES NOMINAL 18″ IN DIAMETER WHILE THE MIDDLE AND BOTTOM ROLLS MEASURE NOMINAL 30″ IN DIAMETER. CHROME ROLLS ARE HYDRAULICALLY ACTUATED VIA A 7.5 HP HYDRAULIC UNIT. ROLL GAPING VIA SERVO MOTOR WITH CONTROL. ROLLS ARE DRIVEN BY A 10 HP INVERTER DUTY MOTOR WITH ENCODER THRU A GEARBOX VIA SILENT CHAIN AND SPROCKET. INCLUDES PULL ROLL STAND WITH 52″ X 8″ DIAMETER ROLLS WITH 5 HP DRIVE SYSTEM, IDLER ROLL CONVEYOR AND STAND ALONE THREE ZONE WATER TEMPERATURE CONTROL SYSTEM WITH HEATERS, HEAT EXCHANGERS, AND ONE(1) 10 HP AND TWO (2) 7.5 HP WATER PUMPS. LAST USED IN LINE WITH A THERMOFORMER. WITH INTEGRAL ELECTRICAL CABINETS AND PENDULUM OPERATOR CONTROLS WITH AB PANEL-VIEW 550 TOUCH SCREEN. 460/3/60. 142 AMPS.

  • Array ( [0] => just-arrived [1] => blow-molding [2] => just-arrived [3] => blow-molding )
  • Stock#: 16577

    USED UNILOY 350R4 BLOW MOLDER


    USED UNILOY MODEL 350R4 BLOW MOLDER, S/N 350R4-3854.  NEW APPROXIMATELY IN 1986.  CURRENTLY INSTALLED WITH (7) PROGRAMMABLE HEADS WITH MACO 8000 CONTROL/PROGRAMMER.  BLOW MOLDER IS EQUIPPED WITH 1600 GRAM SHOT CAPACITY.  PREVIOUSLY USED ON APPROXIMATELY 1 LITER BOTTLES.  MAY ACCOMMODATE GALLON MOLDS IF UTILIZING AS 4-HEAD BY BLANKING EVERY OTHER HEAD.  INCLUDES UNILOY MODEL 10041 TRIMMER.  S/N SW10041-3854

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-lines [3] => just-arrived [4] => pelletizers [5] => pelletizing-lines )
  • Stock#: 16563

    USED 6″ EXTRUSION PELLETIZING LINE


    PELLETIZING LINE CONSISTING OF:

    ONE (1) USED 6″ 30/1 PRODEX MODEL TM-600-30 EXTRUDER HAVING A SIX(6) ZONE ELECTRICALLY HEATED, WATER COOLED(CLOSED LOOP) AND SIDE VENTED BARREL AT APPROXIMATELY A 42″CENTERLINE. INCLUDES 3 HP VACUUM WATER CENTRIFUGAL VACUUM PUMP FOR VENT. UNIT HAS PRODEX/LUFKIN MODEL TMH-60A-315 CHANGE GEAR BOX WITH 10.4:1 GEARS INSTALLED. GEARBOX IS DIRECT DRIVEN BY A 400 HP EMERSON DC MOTOR WITH ABB MODEL DCS-800 DIGITAL SCR CONTROL. 400 HP DC MOTOR WAS CLEANED AND BAKED IN 2017. STAND ALONE TEMPERATURE CONTROL PANEL WITH 12-ZONES DIGITAL CONTROLLERS SET UP FOR SIX (6) BARREL, THREE (3) SCREEN CHANGER AND TWO (2) DIE ZONES. EXTRUDER IS SET UP FOR A CRAMMER FEEDER AND INCLUDES ADAPTER. PRODEX CRAMMER FEED IS AVAILABLE AT ADDITIONAL COST.

    ONE (1) USED XALOY MODEL EH-80 SLIDE PLATE SCREEN CHANGER HAVING TWO (2) NOMINAL 8″ DIAMETER BREAKER PLATES WITH MODEL HPU-50 5 HP HYDRAULIC PUMP POWER PACK AND CONTROLS. MANUFACTURED 2008, SCREEN CHANGER SERIAL NUMBER EH80059.

    3) BERINGER MODEL WRP12 WATER RING PELLETIZING SYSTEM WITH 3-HP CUTTING HEAD, 5 HP CENTRIFUGAL DRYER, AND TEMPERED WATER RECIRCULATION SYSTEM WITH 5 HP PUMP.

    LAST USED ON PP AND PE AT 800-9-LBS AN HR / LAST USED ON HDPE AT 1200 POUNDS AN HOUR.

  • Array ( [0] => just-arrived [1] => rebuilt-granulators-35-hp [2] => recycling [3] => just-arrived [4] => rebuilt-granulators-35-hp [5] => recycling )
  • Stock#: New 37B

    NEW CUMBERLAND 1837B GRANULATOR


    New Cumberland model 1837B granulator, S/N 50510-19007, 18″ x 37″ feed throat, 3 knife high shear rotor, 2 bed knife, 100 HP 460 volt 1775 RPM motor, conveyor in-feed hopper, 8″ airveyor discharge, mounted on a 22″ high plate base, starter and controls not included

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => recycling [3] => just-arrived [4] => miscellaneous [5] => recycling )
  • Stock#: 16414

    USED SATAKE SMII-820XEP COLOR OPTICAL SORTER


    SATAKE MODEL SMII-820EXP SCAN-MASTER II COLOR OPTICAL SORTER, S/N 2011815, 110 VOLT SINGLE PHASE OPERATION, 19 MAXIMUM AMPS, NEW IN 2011

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16399

    USED DAVIS STANDARD 3.5″ 30:1 L/D 200 HP EXTRUDER


    USED DAVIS STANDARD MODEL MV35IN35SR 3.5 EXTRUDER, S/N K2187, SO# 99878, 30:1 L/D BARREL HAVING A SEVEN (7) ZONE ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP), AND SIDE VENTED BARREL AT A 52” CENTERLINE HEIGHT. GEARBOX HAS A 5.67:1 REDUCTION RATIO AND IS RATED AT 158 HP AT A SERVICE FACTOR OF 1.25. GEARBOX IS BELT DRIVEN BY A 200 HP 500 VOLT D/C MOTOR WITH CONTROL TECHNIQUES SCR. INTEGRAL TEMPERATURE CONTROL PANEL HAS TEN (10) ZONES OF BARBER COLEMAN CONTROLLERS. WATER COOLED FEED THROAT. BERINGER MODEL SL35 SCREEN CHANGER IS MOUNTED ON THE BARREL DISCHARGE AND INCLUDES A 3 HP HYDRAULIC POWER PACK WITH HOSES. MANUFACTURED 4/1987. 460/3/60 INPUT POWER

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => extrusion-sheet-lines [3] => just-arrived [4] => extruders-3-5-10 [5] => extrusion-sheet-lines )
  • Stock#: 14893

    USED DAVIS STANDARD 6″ EXTRUDER – 46″ WIDE SHEET LINE


    USED DAVIS STANDARD 46″ WIDE SHEET LINE LAST USED ON PP SHEET AT A RATE OF 1800 LBS AN HR CONSISTING OF:

    A – DAVIS STANDARD MODEL 6IN60TPIN 6″ 30:1 L/D EXTRUDER HAVING A SIX ZONE ELECTRICALLY HEATED, WATER COOLED BARREL (CLOSED LOOP) VENTED BARREL AND PLUGGED, 47” CENTERLINE HEIGHT. GEARBOX HAS A 11.3:1 REDUCTION RATIO AND IS DIRECT DRIVEN BY A 500 HP RELIANCE DC MOTOR WITH 550 KVA ISOLATION TRANSFORMER ALLOWING FOR A MAXIMUM SCREW SPEED OF 154 RPM. GEARBOX HAS A RATING OF 700 HP AT A SERVICE FACTOR OF 1.5. FEED THROAT HAS A 12” X 8” ENTRANCE. EXTRUDER SCREW IS A BARRIER TYPE. CONTROL PANEL WITH SIX EUROTHERM 2208 TEMPERATURE CONTROLLERS FOR THE EXTRUDER BARREL ZONES PLUS 9 MORE DISCRETE CONTROLLERS FOR THE DIE AND DOWNSTREAM ZONES. S/N X7505. MFD 1998

    B – EXTEK MODEL HSC60 SCREEN CHANGER HAVING TWO NOMINAL 6” DIAMETER BREAKER PLATES. INCLUDES 2 HP HYDRAULIC POWER PACK.

    C – XALOY MODEL SPD-300 MELT PUMP WITH 25 HP DRIVE SYSTEM AND CONTROLS.

    D – EDI 44″ MODEL ULTRA-FLEX UHRC-100 FLEXIBLE LIP SHEET DIE HAVING A 45 DEGREE RESTRICTOR BAR. SET UP FOR FIVE ZONES OF TEMPERATURE CONTROL. WITH DECKELING PROVISION. INCLUDES DIE SUPPORT CART WITH CASTERS. 230 VOLT. S/N 98-20339. MANUFACTURED 1998.

    E – DAVIS STANDARD MODEL UPSTACK46 COOL-KING AND POLISHING STAND HAVING THREE NOMINAL 24” DIAMETER CHROME PLATED ROLLS MOUNTED IN A VERTICAL ARRANGEMENT FOR UP-STACK OPERATION. HYDRAULICALLY ACTUATED CHROME ROLLS ARE EACH DRIVEN BY A 3 HP INVERTER DUTY MOTOR WITH ENCODER THRU SEW EURODRIVE 86.34:1 GEARBOXES WITH A 0-1750 RPM SPEED RANGE. INCLUDES PULL ROLL STAND WITH 46” X 8” DIAMETER ROLLS WITH 5 HP DRIVE SYSTEM AND 20′ IDLER CONVEYOR AND THREE ZONE WATER TEMPERATURE CONTROL SYSTEM WITH HEATERS, HEAT EXCHANGERS, AND 7.5 HP PUMPS.

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 16784

    USED 2″ PTI 24:1 L/D 25 HP EXTRUDER


    PTI MODEL 2000 2” SINGLE SCREW EXTRUDER, S/N 2565EXT, 24:1 L/D, NEW 1998, HAS ELECTRICALLY HEATED WATER-COOLED BARREL, INCLUDES PUMP, HEAT EX-CHANGER AND WATER RESERVOIR. BELT DRIVEN BY 25 HP AC MOTOR, 460 VOLT AC INPUT, WITH VARIABLE FREQUENCY DRIVE. HAS TEMPERATURE CONTROL PANEL WITH INDIVIDUAL INSTRUMENTS FOR EACH ZONE. INCLUDES HOPPER WITH ANTI-BRIDGE AGITATOR, SECOND AUXILIARY HOPPER, AND 16-HOLE VERTICAL DOWN STRAND DIE

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 16829

    USED DAVIS STANDARD 2.5″ 24:1 L/D EXTRUDER


    DAVIS STANDARD MODEL 25IN25 2.5″ EXTRUDER, S/N J7013, SO# 98057, ORIGINALLY MANUFACTURED 8/85 AND REBUILT BY DAVIS STANDARD IN 2003. 24:1 L/D ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP) BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A REDUCTION RATIO OF 17.26:1 AND IS RATED AT 75 HP AT A SERVICE FACTOR OF 1.25 TO 1. GEARBOX IS BELT DRIVEN BY A 50 HP DC MOTOR WITH SCR ALLOWING FOR A MAXIMUM SCREW SPEED OF A 100 RPM. INTEGRAL CONTROL PANEL HAS HARDWARE FOR TEMPERATURE CONTROL BUT LACKS INSTRUMENT OR TOUCH SCREEN, C-LAMP ON DISCHARGE, HAS STAINLESS STEEL IN-FEED HOPPER. INCLUDES SCREW IN UNIT AND TWO SPARE SCREWS, 460/3/60 INPUT


  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 16828

    USED DAVIS STANDARD 2.5″ 24:1 L/D EXTRUDER


    DAVIS STANDARD MODEL 25IN25 2.5″ EXTRUDER, S/N J7012, SO# 98057, ORIGINALLY MANUFACTURED 8/85 AND REBUILT BY DAVIS STANDARD IN 2003. 24:1 L/D ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP) BARREL AT A 42″ CENTER-LINE HEIGHT. BARREL IS VENTED BUT PLUGGED, GEARBOX HAS A REDUCTION RATIO OF 17.26:1 AND IS RATED AT 75 HP AT A SERVICE FACTOR OF 1.25 TO 1. 3-3/4″ X 3-3/4″ FEED THROAT WITH NO IN-FEED HOPPER, GEARBOX IS BELT DRIVEN BY A 50 HP 1775 / 3465 RPM A/C MOTOR WITH INVERTER ALLOWING FOR A MAXIMUM SCREW SPEED OF A 100 RPM. INTEGRAL CONTROL PANEL HAS HARDWARE FOR TEMPERATURE CONTROL BUT LACKS INSTRUMENTS OR TOUCH SCREEN, C-CLAMP ON DISCHARGE. INCLUDES TWO SCREWS WITH NEITHER INSTALLED, 460/3/60 INPUT


  • Array ( [0] => just-arrived [1] => extrusion-sheet-dies [2] => just-arrived [3] => extrusion-sheet-dies )
  • Stock#: 16438

    USED EDI 52″ AUTO-FLEX CONTOUR DIE


    EXTRUSION DIES INC AUTO-FLEX AF6R HM40 52″ WIDE CONTOUR DIE, S/N 11-30268, MANUFACTURED 2011, 14 HEATER ZONES 480/1/60, CHROME PLATED FLOW SURFACES, 52 EACH AF6R LIP ADJUSTMENTS, .500 LIP LAND, .025″ LIP OPENING, 10″ PER SIDE FIXED FLEX SIDE DECKLE, 4″ WIDE X 1″ BACK CENTER MATERIAL ENTRANCE, DESIGNED FOR HORIZONTAL OPERATION, OPTIONAL LIP HEATERS WITH TC’S AND THERMOCOUPLES

  • Array ( [0] => just-arrived [1] => extrusion-sheet-dies [2] => just-arrived [3] => extrusion-sheet-dies )
  • Stock#: 16439

    USED EDI AUTO-FLEX 60″ CONTOUR DIE


    EXTRUSION DIES INC AUTO-FLEX AF6R HM40 60″ WIDE CONTOUR DIE, S/N 11-30161, MANUFACTURED 2011, 14 HEATER ZONES 480/1/60, CHROME PLATED FLOW SURFACES, 52 EACH AF6R LIP ADJUSTMENTS, .500 LIP LAND, .025″ LIP OPENING, 10″ PER SIDE FIXED FLEX SIDE DECKLE, 4″ WIDE X 1″ BACK CENTER MATERIAL ENTRANCE, DESIGNED FOR HORIZONTAL OPERATION, OPTIONAL LIP HEATERS WITH TC’S AND THERMOCOUPLES

  • Array ( [0] => just-arrived [1] => 35-60-hp-granulators [2] => feed-paddle-roll-granulators [3] => just-arrived [4] => 35-60-hp-granulators [5] => feed-paddle-roll-granulators )
  • Stock#: 17253

    USED CUMBERLAND 1456i WITH FEED ROLLS


    Cumberland model 1456i granulator, S/N 84000-00005, 14″ x 56″ feed throat, 3 knife twin shear rotor, 2 bed knife, conveyor in feed hopper with rear mounted feed rolls, hopper has dual cylinder hydraulic power back assist, rotor is powered by a 50 hp 460 volt 1185 RPM motor, 8″ left hand airveyor discharge, mounted on a common plate base with vibration control pads, 8″ diameter x 56″ wide knurled steel crusher feed rolls in offset configuration are powered by a 3 HP A/C inverter duty motor thru a gearbox and have pneumatically operated pinch, starter, feed roll v/s drive and controls not included

  • Array ( [0] => just-arrived [1] => 35-60-hp-granulators [2] => feed-paddle-roll-granulators [3] => just-arrived [4] => 35-60-hp-granulators [5] => feed-paddle-roll-granulators )
  • Stock#: 16922

    USED CUMBERLAND 1456 FEED ROLL GRANULATOR


    CUMBERLAND MODEL 1456 GRANULATOR, S/N 84000-87011, 14″ X 56″ FEED THROAT, 3 KNIFE OPEN ROTOR, 2 BED KNIFE, 50 HP 230/460 VOLT 1175 RPM MOTOR, CONVEYOR FEED HOPPER WITH REAR MOUNTED 5″ DIAMETER X 56″ WIDE STEEL KNURLED FEED ROLLS, FEED ROLLS HAVE PNEUMATIC PINCH AND ARE POWERED BY A 1.5 HP 208-230/460 VOLT 1140 RPM MOTOR THRU A 40:1 GEARBOX AND CHAIN & SPROCKET DRIVE SYSTEM, GEARBOX IS RATED FOR A MAXIMUM OF 1.85 HP AND HAS AN OUTPUT TORQUE OF 2080 LBS PER INCH, CHAMBER IS MOUNTED TO A LOW PROFILE PLATE BASE ON VIBRATION CONTROL PADS, 10″ OD AIRVEYOR DISCHARGE, INCLUDES PNEUMATIC AIR VALVE CONTROL SYSTEM FOR THE FEED ROLLS, OVERALL DIMENSIONS ARE 10′ X 80″ X 100″, APPROXIMATELY 10,000 LBS, STARTER AND CONTROLS FOR THE GRANULATOR ARE NOT INCLUDED