Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 17654

    USED EGAN 2″ 24:1 L/D 25 HP EXTRUDER


    One (1) Used 2″ 24’1 Egan extruder having a five (5) zones electrically heated, air cooled, and non-vented barrel at approximately a 50″ centerline height. Extruder is mounted on a mobile cart with casters. If the extruder is removed from the cart it will have a nominal 42″ centerline height. Cone Drive gearbox has a reduction ratio of 10:1 and is rated at 19 HP at a service factor of 1.0. Gearbox is belt driven by a 25 HP D/C motor with an Allen-Bradley model 1395 drive. Unitized temperature control panel has fifteen (15) zones of controllers. C clamp on the barrel discharge. Gravity feed hopper with Conair DB 8 hopper loader on the feed throat. Feed throat entrance is nominal 3″ round. Machine recently updated. Serial number JO 07319-05. 240/3/60 input on the barrel. 460/3/60 on the drive. Several transformers included. Extremely clean. Ideal co-extruder. Approximately 6,000 Lbs.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17542

    USED DAVIS STANDARD 1.5″ 34:1 L/D EXTRUDER


    one (1) used Davis Standard model Thermatic 150 1.5″ extruder, S/N 62570, 34:1 L/D barrel having a five (5) zone electrically heated, air cooled, and non-vented barrel at approximately a 42? centerline height. Gearbox has a reduction ratio of 11.31:1 and is rated at 18 HP at a service factor of 1.5. gearbox is belt driven by a 15 HP D/C motor with isolation transformer and Reliance SCR control. Unitized temperature control panel has eight zones of controllers consisting of five (5) zones for the barrel and three (3) zones for the die. S/O 9077. C-clamp on discharge. 460/3/60 input power. Includes spare cast aluminum barrel heater and screen packs

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17529

    USED KILLION KN-150 1.5″ 24:1 L/D EXTRUDER


    One (1) Used Killion model KN-150 1.5″ extruder. 24:1 L/D barrel having four (4) zones electrically heated, air cooled, and non-vented barrel at approximately a 39? centerline height. Koellmann model PEZS20 gearbox has a reduction ratio of 11.2:1 and is rated at 16 hp at a service factor of 1.0. Gearbox is belt driven by a 15 HP D/C motor with Emerson Mentor II SCR control. Unitized temperature control panel has seven (7) zones of controllers consisting of four zones for the barrel and three (3) zones for the downstream. Swing away die holder with adapter on the discharge. very clean. 230/3/50-60 input

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17577

    USED WELEX 2.5″ 24:1 L/D 40 HP EXTRUDER


    One (1) used 2.5″ 24:1 L/D Welex extruder having an electrically heated water-cooled and, non-vented barrel at a 64″ centerline height. Gearbox is a Koellmann model PEZS312 and has a reduction ratio of 9.3:1 with a 110 HP rating and a service factor of 1.0. Gearbox is driven by a 40 HP D/C motor. 3.5″ x 5.5″ feed throat entrance. S/N 6639. Manufactured in June of 1997. No controls

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17576

    USED WELEX 2″ 24:1 L/D CO-EXTRUDER (NO MOTOR)


    One (1) used 2″ 24:1 L/D Welex co-extruder. Water cooled. Missing motor, drive panel, and pedestal. Last used on a sheet line.

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => extrusion-sheet-dies [3] => lab-testing-equipment [4] => just-arrived [5] => extruders-34-3 [6] => extrusion-sheet-dies [7] => lab-testing-equipment )
  • Stock#: 17556

    USED DAVIS / KILLION LAB SHEET / CAST EXTRUSION LINE


    Used 16″ Davis Standard Pilot / Laboratory size horizontal sheet/cast line consisting of the following:

    (2) 1″ Killion / Davis Standard pedestal style co-extruders each 30:1 L/D driven by 3 HP A/C motors with individual temperature control panels, general purpose 3:1 barrier type screw, air cooled barrels and melt pumps. Includes one (1) spare screw.

    (1) 1.25″ Killion / Davis Standard primary 30:1 L/D extruder driven by a 15 HP A/C motor, general purpose 3:1 barrier type screw, individual temperature control panel, gear pump, and air-cooled barrel. Includes four (4) spare screws.

    (1) Cloeren Co Ex Block with multiple inserts for co-extrusion. Inserts include AAAAA, BBAAA, CBAAA, AABAA, CAAAB, CCCCC, CBABC, BAAAB, and ABCAA configurations. Manufactured in 2006.

    (1) 14″ Cloeren sheet die having a center back entrance but mounted for use in a downward direction. S/N A06-1782-02. Manufactured in 2006

    (1) Davis Standard horizontal sheet chill roll stack with three (3) 16″ wide x 24″ OD rolls. With individual motor drive through a gearbox for each roll and built onto frame hydraulic roll loading. Rotary unions for roll cooling/heating with Conair model TC1 stand-alone temperature control. Unit can be run as a cast unit or sheet take-off. With pull rolls.

    Also Includes two (2) matt finished rolls, one (1) silicon covered roll and four (4) chrome rolls. Still installed as operated until June 25 2021. New approximately 1995-2006 with laboratory use only.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17550

    USED KILLION KN100 1″ 24:1 L/D EXTRUDER


    One (1) used Killion model KN-100 1.00″ 24:1 L/D extruder having a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 39″ center line height. Gearbox is belt driven by a 3 HP D/C motor with SCR control. Unitized temperature control panel has Four (4) zones of temperature controllers consisting of three (3) zones for the barrel and one (1) zone for the die. Includes gravity feed hopper. S/N 8173N. 230V/1ph/50-60Hz input, 38.5 FLA

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 17504

    USED DAVIS STANDARD 1.5″ 20:1 L/D RUBBER EXTRUDER


    One (1) used 1.5″ 20:1 L/D ratio Davis Standard rubber extruder with powered feed roll on throat. Barrel is electrically heated, water cooled (closed loop) and vented at approximately a 42″ centerline height. Includes oil style vacuum pump. C-clamp with die on barrel discharge. Oversize gearbox has a reduction ratio of 17.56:1 and is rated at 50 HP at a service factor of 1.25:1. Gearbox is belt driven by a Marathon Blue Max 25 HP A/C motor with Allen Bradley Power Flex 753 inverter with isolation transformer. Unitized temperature control panel has seven (7) zones of temperature controls. Manufactured January of 2001. Model 150IN20. Shop order number 71118. S/N 16633. 460/3/60 input. 77 FLA.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17438

    USED WELEX 2″ 24:1 L/D EXTRUDER


    Welex model 200-24/1, 2″ 24:1 L/D extruder with a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 50″ centerline height. Gearbox is a Koellmann Gear and is belt driven by a 20 HP D/C motor with SCR control. D/C motor was recently replaced. Unitized temperature control panel with six (6) zones of controllers consisting of three zones for the barrel and three die zones. Swing gate on discharge. Gravity feed hopper. S/N 2235 3-83. 460V/3ph/60Hz input. Includes the documentation manual.

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 17437

    USED DAVIS STANDARD 1/4″ TUBING EXTRUSION LINE


    Davis Standard 1/4″ tubing extrusion line including the following equipment:

    A. Davis Standard / Killion model KN-100 1.00″ 24:1 L/D extruder having a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 39″ centerline height. Gearbox is belt driven by a 3 HP D/C motor with SCR control. Unitized temperature control panel has six (6) zones of Eurotherm controllers consisting of three (3) zones for the barrel and three (3) zones for the c-clamp and die. C-clamp is mounted on the discharge. Includes gravity feed hopper. BOM number 05180. 230V/1ph/50-60Hz input, 47 FLA.

    B. Nominal ¼” diameter electrically heated tubing die.

    C. Davis Standard / Killion medical tubing vacuum tank measuring 116″ long with an 8″ x 8″ cross section. Stainless steel construction. Two glass doors. Upstream and downstream adjustment as well as up and down adjustment. Includes vacuum pump with 3 HP D/C motor, water pumps, sizing fixture, and controls. S/N 30176. 230V/1ph/60Hz input.

    D. Davis Standard / Killion belt puller having a 2″ wide belt with 22″ of contact length. Powered by an approximate 1.5 HP D/C motor. Manually actuated top belt. S/N 30174. 230V/3ph/60Hz input, 10 FLA.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 16305

    USED KILLION 1″ 24:1 L/D EXTRUDER


    24:1 Killion pedestal extruder. S/N N6598 with a three (3) zone electrically heated air cooled barrel. Gearbox has a reduction ratio of 30:1 and is direct driven by a 3HP 1750/2050 RPM DC motor. Barrel can be raised or lowered and also tilts for co-extrusion applications. Integral temperature control panel has four zones of Eurotherm temperature controllers. Pressure gauge on discharge. Mounted on casters.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 16275

    USED WAYNE 1″ 30:1 L/D EXTRUDER


    Wayne Extruder 1″ 30:1 L/D extruder with a three zone electrically heated air cooled non-vented barrel at approximately a 39″ centerline height. Gearbox is belt driven by a 5HP DC motor with SCR control. Extruder discharge has a manual screen changer, static mixer, and a 4 hole strand die on the discharge. Unitized temperature control panel has six zones of 1/8 DIN controllers consisting of zones for three barrels. One screen changer, one static mixer, and one zone for the strand die. Serial number 7502. Manufactured 2003. 230V/3ph/60Hz operation.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 16360

    USED WAYNE 1″ LAB EXTRUDER


    Wayne 1″ extruder S/N 1889-884, electrically heated air cooled non vented barrel.

  • Array ( [0] => used-equipment [1] => extruders-34-3 [2] => used-equipment [3] => extruders-34-3 )
  • Stock#: 14768

    BELLAFORM MODEL BH25-25D 25mm EXTRUDER


    Bellaform co-extrusion package consisting of the following:

    Bellaform model BH25-25D 25mm extruder. S/N P19-330877, 10.5 kW AC motor with tachometer and drive, 220-Volt operation. 25:1 L/D air cooled barrel with 3 heating and cooling zones. Has 3 kW heating capacity and a 155 RPM screw speed, and a 43″ centerline. Includes the control panel. Bellaform model BH45-25D 45mm extruder S/N P19-330875 31 kW AC motor with tachometer and drive 220-Volt operation. 25:1 L/D air cooled barrel with 3 heating and cooling zones and a 6.5 kW heating capacity, 227 RPM screw speed and a 43″ centerline. Includes the control panel. Six (6) station model 2200 Plasticolor additive feeding system, S/N 10011. Includes 6 Schmidt & John 1.5″ inlet vacuum loaders controls for feeder. Loaders are in the extruder control panels. All items were manufactured in 2000.

    Two complete systems are available.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 16607

    USED DAVIS STANDARD DS-125 1.250″ 24:1 L/D EXTRUDER


    Davis Standard model DS-125 pedestal extruder, S/N K-3031. 24:1 L/D electrically heated 3 zone air cooled barrel with adjustable height and angle. Pedestal mounted stand alone control panel. 15:1 gearbox ratio. 7HP maximum capacity motor with a 1.25 service factor.

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 16355

    USED WAYNE 1.250″ 30:1 L/D EXTRUDER


    Wayne 1.25″ extruder, S/N 9414-832. 30:1 L/D electrically heated, air cooled, vented (venting is plugged), barrel driven by a 7.5HP DC motor with SCR control 230-Volts input power. Includes track wheel base and a spare screw.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 16432

    USED KILLION 1.250″ 30: 7.5 HP EXTRUDER


    USED  KILLION MODEL KN-125 1.25” 30:1 EXTRUDER HAVING A FOUR (4) ZONE ELECTRICALLY HEATED, AIR COOLED NON-VENTED BARREL AT APPROXIMATELY A 39″ CENTERLINE HEIGHT. GEARBOX IS A  KOELLMANN MODEL PEZS 20, HAS A REDUCTION RATIO OF 11.2:1 AND IS RATED AT 16 HP AT A SERVICE FACTOR OF 1.0. GEARBOX IS BELT DRIVEN BY A 7.5 HP DC MOTOR WITH SCR CONTROL. UNITIZED TEMPERATURE CONTROL PANE HAS FIVE ZONES OF 1/4 DIN CONTROLLERS CONSISTING OF FOUR ZONES FOR THE BARREL AND ONE (1) ZONE FOR THE DIE. SERIAL NUMBER 3193.  230/3/50-60 INPUT. 63 FLA.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 12754

    USED DAVIS STANDARD MODEL 15INDS20 1.5″ EXTRUDER


    Davis standard model 15INDS20 1.5″ extruder S/N K-9754. SO# 02359. 24:1 L/D. Powered by a fan cooled 15 HP 500-Volt 1750/2300 RPM DC motor through a 6.53:1 gearbox 152 RPM screw speed. Electrically heated and fan cooled 4 zone barrel at a 42″ centerline. 50 HP capacity gearbox with a 1.5 service factor. Chrome plated single stage double wave screw with Madux mixer, 460V/3ph/60Hz input to control panels. Reliance Maxpak III V/S drive Maco / Davis 8000 and 8801 controllers. Includes handy clamp and additional drives that are operational. Unit does not include belt puller and melt pump. All manufactured July 1989.

  • Array ( [0] => used-equipment [1] => extruders-34-3 [2] => used-equipment [3] => extruders-34-3 )
  • Stock#: 8891

    JOHNSON 1.5


    Johnson 1-1/2″ extruder, 24:1 L/D. Non-vented barrel mounted on a base for co-extrusion. 10HP DC motor with no controls. S/N 7619-15. 11.32:1 gear box, 41 HP with a 1.25 service factor. No barrel cooling.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 16125

    USED NRM / DAVIS STANDARD 1.5″ EXTRUDER


    NRM / Davis Standard 1.5″ Pacemaker IV extruder, S/N 19218, S/O 52660. 24:1 L/D air cooled electrically heated barrel with a 42″ to 44-3/4″ adjustable centerline. Driven by a 10 HP 1750/2300 RPM DC motor with Reliance variable speed drive, 6 heat zones with a Watlow 93 temperature controls (3 are missing). Includes Conair Microline vacuum loader with a 1.5″ inlet.