Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17407

    USED LEISTRITZ 50mm TWIN SCREW EXTRUDER


    Leistritriz 50mm twin screw compounding extruder with a 40:1 L/D ratio. Screws are co-rotating and inter-meshing at a 42″ center-line height. Feed entrance is 3″ x 3″. Barrel is electrically heated and water cooled and consists of ten (10) barrel sections including feed, top vent, side feed, and seven (7) closed sections. Screws and barrel sections were replaced in 2016. Eisenbeiss gearbox was replaced in 2015 and is direct driven by a 54 KW (72 HP) A/C motor with Emerson Quantum III control. Gearbox is rated at 2 x 600 newton meters. Free standing control panel with eleven (11) zones of temperature controls that also houses the drive control and operator controls. Package includes Leistritz side feeder with twin screws and 1.5 kw drive and 2.2 kw water centrifugal vacuum pump with micron technology filter. Pulled from service in March of 2021. Last used for compounding LDPE. 460V/3ph/60Hz. 250 amp main disconnect.

  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => pelletizing-lines [3] => just-arrived [4] => extruders-twin-screw [5] => pelletizing-lines )
  • Stock#: 17395

    USED LEISTRITZ/GALA 27mm COMPOUNDING LINE


    Leistritz / Gala 27mm compounding line consisting of the following components:

    One 27mm 40:1 Leistritz model Micro 27 40GL/40D twin screw extruder with co-rotating inter-meshing screws. Barrel is electrically heated, water cooled and consists of nine (9) barrel sections. Gearbox is direct driven by a 10.5 KW (14.3 HP) DC motor with SCR (silicone controlled rectifier) allowing for an approximate maximum screw speed of 500 RPM. Integral movable control panel has eleven (11) zones of temperature control and all operator controls. Includes pre-polymer metering pump and three (3) sets of screw shafts with loose screw elements. Manufactured in 1997. S/N 2553. Pulled from service in January of  2021. Gala model 6PDV polymer diverter valve with 10 HP hydraulic pump. Unit is used until the extruder is up to speed. Gala model SLC6 underwater pelletizer with 4.3 KW (5.3 HP) spring loaded cutter, model 40TWS water tempering system with heated reservoir, 3 HP water pump, heat exchanger, Gala model 8.1BF spin dryer with agglomerate catcher and free-standing control panel with touch screen controls. Offered less die. Includes spare blades, heater bands, and manuals. 460V/3ph/60Hz 46 FLA operation . Manufactured in 2000. S/N 10100743.

  • Array ( [0] => extruders-twin-screw [1] => extruders-twin-screw )
  • Stock#: 17064

    USED BERSTORFF 25MM TWIN SCREW EXTRUDER


    Berstorff 25mm twin screw extruder type ZE25. Co-rotating side by side screw design. 36:1 L/D ratio. Electrically heated and air cooled barrel consisting of eight sections including feed throat, 42″ barrel centerline height, side feeder entrance, and vent section. Accurate feeder mounted on the feed throat and K-Tron feeder for side feeder. 15HP DC motor with SCR. Console type control panel with seven zones of temperature control. Two hole strand die, operator and feeder controls are included. Manufactured in 1994. 240-Volt input power.

  • Array ( [0] => extruders-twin-screw [1] => extruders-twin-screw )
  • Stock#: 16620

    USED STEER ENGINEERING 12mm TWIN SCREW EXTRUDER


    Steer Engineering Pharmaceutical twin-screw extruder, S/N EA00427. Model Omicron 12P new in 2014. Screw diameter is 12mm diameter ratio (do/di) is 1.45 flight depth is 1.9 max screw speed is 900 RPM 2HP drive, 480V/3ph/60Hz operation.

  • Array ( [0] => extruders-twin-screw [1] => extruders-twin-screw )
  • Stock#: 16813

    USED BRABENDER 25mm TWIN SCREW EXTRUDER


    Brabender model 088 twin screw extruder, air cooled. Includes DC motor and temperature control panel.