Array ( [0] => extrusion-sheet-lines [1] => extrusion-sheet-lines )
  • Stock#: 17461

    USED EDI UHRC-100 44″ SHEET DIE


    One (1) used Nordson/ Extrusion Dies Inc Model Ultra-100 heavy duty sheet die with a 44″ slot opening. Integral upper flexible lip and fixed removable lower lip. Adjusting bolts on 1″ centers. 45 degree restricter bar.100″ flex adjustment. Coat-hanger manifold. Extrusion Dies serial number 98-20339. Back center feed. Last ran polypropylene with a 6″ 30:1 500 HP Davis Standard extruder.. Extremely clean. Set up for five (5) zones of temperature control. Deckling provision. 230V/1ph/60Hz input. Includes a steel die cart. Manufactured in 1998

  • Array ( [0] => used-equipment [1] => extruders-3-5-10 [2] => extrusion-roll-stacks-rolls [3] => extrusion-sheet-lines [4] => used-equipment [5] => extruders-3-5-10 [6] => extrusion-roll-stacks-rolls [7] => extrusion-sheet-lines )
  • Stock#: 16932

    USED PTI 78″ SHEET LINE


    PTI 78″ wide sheet line manufactured in 2003, last used on a PET sheet. This line consists of the following:

    One (1) PTI model 6000 6″ 36:1 L/D extruder with an eight (8) zone electrically heated water cooled (closed loop) and vented barrel at a 64″ center-line height. Gearbox is a Flender model SZNF390 with a 15.4:1 reduction ratio rated for up to 986 HP. Gearbox is directly driven by 500 HP DC motor. Offered less SCR control. Screw is designed for use on PET and has provision for cooling. Control panel has 25 zones of Eurotherm controllers. S/N 3767/10082. Manufactured in June, 2003.

    One (1) Dynisco model EH-60 screen changer with two nominal 6″ diameter breaker plates. Includes a 2HP hydraulic power pack.

    One (1) Maag model 90/90 melt pump with 30HP drive, system controls, and model 6000 static mixer.

    One (1) Cloeren 70″ auto-flex sheet die. 1″ x 4″ back center feed entrance. S/N 77831-2129. Manufactured April, 2003.

    One (1) PTI model 7824 down stack roll stand having three rolls mounted in a vertical arrangement consisting of 24″ diameter middle and bottom chrome plated rolls and a 16″ diameter chrome plated top roll. Hydraulically actuated gapping. Rolls are driven by a 10HP AC motor through gearboxes via silent chain and sprockets. Includes temperature control system built onto frame (missing one pump), idler conveyor, dip coating station, slitting station, and pull roll stand with 78″ x 8″ diameter rolls. S/N 3354R. 480V/3ph/60Hz operation at 175 amps.

    One (1) 78″ Parkinson turret winder having four winding positions. Each station is driven by a 5HP AC motor. Includes three winding shafts. Missing gearbox on turret.


  • Array ( [0] => extruders-3-5-10 [1] => extrusion-sheet-lines [2] => extruders-3-5-10 [3] => extrusion-sheet-lines )
  • Stock#: 16744

    USED CROWN 4.5″ EXTRUSION SHEET LINE


    Complete extruder line consisting of the following:

    One (1) 4.5″ 32:1 L/D ratio extruder having a seven (7) zone electrically heated air cooled and vented barrel at a 64″ center-line height. Gearbox has a reduction ratio of 18:1 and is direct driven in a tuck under manner by a 250HP Baldor AC motor with an ABB ACS800 inverter. Temperature control panel with seven (7) barrel zones and eleven (11) downstream zones of Eurotherm model 3216 temperature controllers.

    One (1) 4.5″ Berringer model SC4 hydraulic slide pate screen changer with hydraulic power pack.

    One (1) Maag model EXTREX 70 melt pump with 15HP AC motor. Drive is integrated into extruder panel. S/N 50138190-10

    One (1) 48″ wide flex lip die mounted on a stand.

    One (1) 64″ wide cooling and polishing stand having a 16″ diameter top roll 24″ diameter middle and bottom roll mounted in a vertical arrangement for down-stack operation. Rolls are driven via silent chain drive by a 5HP DC motor. Rolls are air actuated. Includes dip tank idler roll conveyor, 64″ wide pull rolls with temperature control system with 7.5HP pumps and built onto frame.

    One (1) Hobbs single turret 2-position winder able to handle up to 36″ diameter packages on 3″ air shafts.

  • Array ( [0] => extruders-3-5-10 [1] => extrusion-sheet-lines [2] => extruders-3-5-10 [3] => extrusion-sheet-lines )
  • Stock#: 14760

    USED WELEX 3.5″ EXTRUDER – 41″ WIDE WELEX SHEET LINE


    Welex 41″ wide sheet line consisting of:

    A) Welex model 3.5-30:1-LHSV 3.5″ 30:1 L/D extruder having an electrically heated water cooled (closed loop) barrel vented and plugged barrel at a 55″ centerline height. Lufkin change gear gearbox is direct driven in a tuck under manner by a 150HP Reliance DC motor with a Reliance SCR control. S/N 4746. Manufactured in May of 1988. Integral panel with controls. Includes two stage screw and spare screw.

    B) Berringer screen changer having two nominal 3.5″ diameter breaker plates. Includes hydraulic power pack.

    C) Welex / Maag model 56/56 melt pump with 20HP drive system. Includes co-ex block and static mixer.

    D) EDI 34″ model R-75 flexible lip sheet die having a 45 degree restrictor bar and removable lower lip. Includes die cart.

    E) 41″ Welex model 18×41-RHSL, S/N 4750, cooling and polishing stand with three 18″ (nominal) diameter chrome plated rolls mounted in a vertical arrangement for down stack operation. Air actuated chrome rolls are driven by an approximately 5HP DC motor through a gear reducer via silent chain and sprocket. Includes a stand-alone pump group with controls. Chain hoist for up and downstream movement on the sheet take-off. Used Welex 42″ wide x 6″ OD rubber / metal pull roll package driven by a 1HP motor. Includes two razor slitting blades for edge trim.

  • Array ( [0] => extruders-3-5-10 [1] => extrusion-sheet-lines [2] => extruders-3-5-10 [3] => extrusion-sheet-lines )
  • Stock#: 14893

    USED DAVIS STANDARD 6″ EXTRUDER – 46″ WIDE SHEET LINE


    Used Davis Standard 46″ wide sheet line last used on PP sheet at a rate of 1,800 Lbs. per hour consisting of the following pieces:

    One (1) Davis Standard model 6IN60TPIN 6″ 30:1 L/D extruder having a six zone electrically heated water cooled (closed loop) vented and plugged barrel with a 47″ centerline height. Gearbox has a 11.3:1 reduction ratio and is direct driven by a 500HP Reliance DC motor with a 550 kVa isolation transformer allowing for a maximum screw speed of 154 RPM. Gearbox has a rating of 700HP at a service factor of 1.5. Feed throat has a 12″ x 8″ entrance. Extruder screw is a barrier type. Control panel with six (6) Eurotherm 2208 temperature controllers for the extruder barrel zones plus Nine (9) more discrete controllers for the die and downstream zones. S/N X7505. Manufactured in 1998.

    One (1) Extek model HSC60 screen changer having two nominal 6″ diameter breaker plates. Includes 2HP hydraulic power pack.

    One (1) Xaloy model SPD-300 melt pump with 25HP drive system and controls.

    One (1) EDI 44″ Ultraflex model UHRC-100, flexible lip sheet die having a 45-degree restrictor bar. Set up for five zones of temperature control. Also has deckling provision. Includes die support cart with casters. 230V operation. S/N 98-20339. Manufactured in 1998.

    One (1) Davis Standard model UPSTACK46 cooling and polishing stand having three nominal 24″ diameter chrome plated rolls mounted in a vertical arrangement for up stack operation. Hydraulically actuated chrome rolls are each driven by a 3HP inverter duty motor with encoder through Sew Eurodrive 86.34:1 gearbox with a 0-1,750 RPM speed range. Includes pull roll stand with 46″ x 8″ diameter rolls with a 5HP drive system and 20-foot idler conveyor and three zone water temperature control system with heaters heat exchangers and 7.5HP pumps.

  • Array ( [0] => extrusion-sheet-lines [1] => extrusion-sheet-lines )
  • Stock#: 16277

    USED 46″ EDI SHEET DIE


    EDI 46″ SHEET DIE, S/N 90-13289-02-03, RE-WORKED 2003, 1.75″ REAR CENTER MATERIAL ENTRY

  • Array ( [0] => extrusion-sheet-lines [1] => extrusion-sheet-lines )
  • Stock#: 14888

    USED 48” WIDE x 24″ WELEX / DAVIS STANDARD SHEET LINE


    One (1) used 48″ x 24″ Welex / Davis Standard sheet extrusion line consisting of the following:

    A) 2.5″ 24:1 L/D Welex extruder having an electrically heated water-cooled barrel at a 60″ centerline height. Gearbox is a Koellmann model PEZS312 and has a reduction ratio of 9.3:1 with a 110HP rating and a service factor of 1.0. Gearbox is driven by a 40HP motor. 3.5″ x 5.5″ feed throat entrance. Serial number 6639. Manufactured in June of 1997

    B) 3.5″, 30:1 L/D Welex extruder having an electrically heated water cooled (closed loop) non vented barrel at a 53″ center line height. Koellmann gearbox has a reduction ratio of 11.919:1 with a rating of 153HP with a service factor of 1.0. Gearbox is driven by a 100 hp motor. 5-3/8″ x 5″ feed throat entrance. No screen changer on discharge. Model 350-2-1984-RHNV. Manufactured in 1984.

    C) 3.5″, 30:1 HPM extruder having an electrically heated water cooled (closed loop) vented and plugged barrel. Koellmann gearbox is driven by a 100HP DC motor with a Eurotherm drive control. 5-3/8″ x 5″ feed throat entrance. Berringer screen changer on discharge.

    D) 4.5″, 30:1 Welex extruder having an electrically heated water cooled (closed loop) barrel at a 56″ centerline height. Gearbox has a reduction ratio of 14:1 with a rating of 373HP with a service factor of 1.0. Gearbox is driven by a 250HP DC motor. Offered less the drive control. Berringer model NC45 screen changer on discharge. Includes a 3HP hydraulic power pack. Extruder model 450-30-RHSV. Manufactured in February of 1982.

    E) Dynisco melt pump with 20HP drive system.

    F) 44″ Cloeren sheet die with co-ex block mounted on a cart.

    G) 48″ Davis Standard cooling and polishing stand having three nominal 24″ diameter chrome plated rolls mounted in a vertical arrangement for down stack operation. Rolls are pneumatically actuated. Chrome rolls are driven by via silent chain and sprockets. Includes 48″ pull roll stand with 5HP drive system. 10′ idler conveyor and a built onto frame three zone water temperature control system with heaters, heat exchangers, and pumps.

    H) Miscellaneous adapters, static mixers, pneumatic conveyors, and receivers.

    I) 2″, 24:1 L/D, Welex co-extruder. Water cooled. Missing motor and drive.