Rapid model 1831K granulator, S/N 70.923, 18″ x 31″ feed throat, 3 knife open rotor, 2 bed knife, 50 HP 460-volt motor, tangential cutting chamber, insulated tray feed hopper and body panels, airveyor discharge, 5/16″ holes screen installed, complete with starter and controls.
Cumberland / Gloucester model 1842i granulator. 18″ x 42″ feed throat with three (3) knife open rotor. Rotor is belt driven by a 100HP 1,775 RPM 460V 134 FLA motor. Two (2) bed knives. Insulated tray feed hopper with 19.5″ x 42″ opening. Insulated body panels. Set up for 6″ OD airveyor discharge. Discharge is via a Sterling model 6005FV blower with a 7.5 HP motor. Includes a free standing console type control panel with Alan Bradley Dialog Plus soft starter. Granulator S/N 01703024.
Granutec model TFG3636-125 granulator having a 36″ x 36″ feed throat. Tangential cutting chamber with three (3) knife open rotor. Two (2) bed knives. Rotor is belt driven by a 125 HP 460-volt 1185 RPM 146 FLA motor. Tray feed hopper. Granulator and controls are mounted on a base plate with fork lift rails. Discharge is set up for an 8″ right hand airveyor. Discharge is via a Kongskilde model MTD-35 blower with 15 HP motor and steel reinforced impeller. Blower discharges into a Kongskilde model RC40 cyclone with nine (9) bag filter head, Kongskilde RF20 rotary valve, and material holding bin. Bin measures 48″ x 48″ x 127″ tall plus 24″ of 45-degree slope. Bin also has 6″ OD gaylord height discharge, Granulator S/N 1205-4296.
Cumberland model 20C granulator, S/N not legible. 9″ x 20″ feed throat, direct driven 3 knife rotor, 2 bed knife cutting chamber, 75HP 885 RPM 460V motor. No infeed hopper, gravity discharge, mounted on a 84″ wide x 39″ deep base, with starter and controls.
Cumberland model 585 granulator. S/N 35910-746. 14″ x 20″ feed throat, 3 knife open rotor, 2 bed knife, 30HP 230/460V motor, wired for 460V. Tray feed hopper, 3″ OD vacuum take off discharge. Mounted on casters, complete with starter and controls.
Granutec model TFG1424 granulator. S/N none. 14″ x 24″ feed throat, 3 knife slant cut open rotor, 2 bed knife, 50HP 460V motor. Insulated tray feed hopper and body panels, 6″ airveyor discharge, complete with starter and controls for granulator and a blower. Blower is not included.
Nelmor model G1436MB granulator. S/N 7306-3952. 14″ x 36″ feed throat, 3 knife solid rotor, 2 bed knife, 50HP 230/460V motor. Forklift base insulated body panels and feed roll in-feed hopper with 8″ x 13″ side hand feed and rear clean out door, 8″ airveyor discharge. 35.5″ wide x 4″ diameter front mounted knurled steel feed rolls with pneumatically operated roll pinch. 30″ wide in-feed trumpet with roller and dancer bar feed rolls, powered by a 1HP 90V 1,750 RPM DC motor through a 15:1 gearbox. Includes stand alone 460V panel with starter and controls for the granulator and a 10HP discharge blower. Penta model KDRG-2250 DC variable speed controller with forward / reverse / jog functions for the feed rolls. Line speed is 122 FPM.
Nelmor model G1436MB granulator. S/N 9604-37866. 14″ x 36″ feed throat, 3 knife solid rotor, 2 bed knife, 100HP 230/460V 1,770 RPM motor, wire for 460V. MB series heavy duty out-board bearing design. 8″ OD right hand airveyor discharge. Insulated body panels. Chamber mounted to 85″ x 76″ plate sheet feed hopper with a 36″ wide x 5.5″ opening and approximately 66″ long. 1/2″ holes screens are installed. Includes a soft starter control panel. Also includes a Nelmor model F819 10HP blower, V-belt driven by a 220/460V 3,500 RPM motor, with sound suppression enclosure, and a medium cyclone that measures 36″ diameter barrel, 23″ straight side, 68″ long cone, with an 8″ inlet and 9″ outlet, with an approximately 20″ top opening and single bag filter head.
Cumberland model 1524B granulator. S/N 58500-6830. 15″ x 24″ feed throat, 3 knife high shear rotor, 2 bed knife, 50HP 230/460V motor. Tray feed hopper. Mounted on a tall gaylord discharge base. 6″ airveyor discharge. Includes spare knives. Starter and controls are not included.
Cumberland model 3715H hog granulator. S/N 250400-81001. 18″ x 37″ feed throat, 15 knife hog rotor, 2 bed knife. 150HP 460V 1,180 RPM motor, 84″ x 72″ x 53″ base with 46″ of gaylord clearance. 9.5″ ID 14″ OD flange airveyor outlet. Needs assembly and it is missing motor pecker head cover. Includes spare 3/8″ and 1/8″ perforated screens. Starter and controls are not included.
Ball & Jewel model SB10/614-A-11 shredder, grinder combination package. Shredder S/N 6646-122958, dual shafts with 1.250″ wide single hook knives powered by a Marathon 10HP 230/460V 1,155 RPM motor through a gearbox. Unit has a 24″ wide x 22″ chamber area, 100″ in-feed height gravity discharges into a Ball & Jewel model SG2026-SX granulator, S/N 6647-122958, 3 knife rotor with knife carriers, 2 bed knives. Powered by a 50HP 460V motor. 3/8″ screen is installed. 5″ OD airveyor discharge with a Bindicator. System is mounted on a 65″ wide x 38″ deep plate base with v-casters and v-track. Includes starter and control panel.
Cumberland model 1837B granulator. S/N none. 18″ x 37″ feed throat, 3 knife steep angle rotor, 2 bed knife. 75HP 460V motor, 6″ airveyor discharge, conveyor feed hopper, 22″ leg base, mounted to a fork lift rail frame. Includes unitized sterling model 6075FD blower, and a #8 sterling cyclone with stand.
MA Industries model 061995-A209 granulator. S/N N-737-1045. 18″ x 37″ feed throat, 3 knife high shear rotor, 2 bed knife. 100HP 460V motor, tray feed hopper, 10″ bolt flanged airveyor discharge mounted on a 40″ deep x 88″ wide x 52.5″ tall step base. 36″ wide clear space under chamber. Includes across the line starter with controls.
Conair / Wortex model 2040HD granulator, S/N 0-5036. 20″ x 40″ feed throat, 3 knife open rotor, 2 bed knife. 75HP 230/460V 1,780 RPM motor. Conveyor feed hopper with pneumatic tilt back assist, 6″ airveyor discharge. Mounted on a short leg base, starter and controls are included.