-
Stock#: 17818
UNUSED STERLING 4X7 CUTTER BLOWER SYSTEM
One(1) unused frame mounted Sterling cutter blower system consisting of one model 4 x 7 cutter with two (2) rotating blades and one (1) stationary blade directly driven by a 2 HP A/C motor. With muffler. S/N 88014. One (1) model 6005HFD blower with steel impeller directly driven by a 5 HP 3450 RPM motor. S/N 88014. Also includes control panel with starter and operator controls. 460/3/60 input
-
Stock#: 17776
USED ARPAC EZ006-L PALLET WRAPPER
Arpac model EZ006-L pallet wrapper, S/N 8746, 1/3 HP 115-volt motor, 4,000 Lb. load capacity, up to 59.5″ diameter 86″ tall wrap object, manufactured in 2007
-
Stock#: 17870
USED BISHMON INDUSTRIES LX-200WM LIFT TABLE
Bishmon Industries model LX-200WM lift table, 2 HP 208/230-volt motor, 4400 Lbs lift capacity, 45″ x 61″ table area, 4.3″ minimum height. 39.4″ maximum height. 23 seconds up travel. 36 seconds down travel. 1100 Lbs. Includes auxiliary pump and control pendant.
2 Available
-
Stock#: 17806
USED PCI 78FP IN-LINE CHOPPER WITH BLOWER
One (1) used frame mounted PCI model 78FB cutter with two (2) rotating blades and one (1) stationary blade directly driven by a 2 HP 208-230/460-volt 1725 RPM A/C motor. Two trim inlets. S/N 71992. Trim cutter on unitized frame with Sterling model 6UHE blower with aluminum impeller and direct drive 5 HP 3450 RPM motor. S/N 13871 88. Includes integral control panel with motor starters and operator controls. 460/3/60 input.
-
Stock#: 17868
USED SOUTHWORTH LS2-48 LIFT TABLE
Southworth model LS2-48 lift table. 2,000 Lb. lift capacity. 48″ x 66″ table area. 8″ minimum height and 56″ maximum. Powered by a 3.2 HP 460/3/60 motor. Includes operator pendant. 950 Lbs.
2 Available
-
Stock#: 17777
USED SOUTHWORTH SPTU2-85 POWER LIFT / TILTER
Southworth Products model SPTU2-85 powered lift / manual-push container tilter. S/N 93155-1/1295274-1, 2,000 Lbs. load capacity. Hydraulic lift mechanism, locking casters, includes pendant up / down controller. Needs a new battery, but otherwise works fine.
-
Stock#: 17728
USED VESTIL SWA-48 PALLET WRAPPER
Vestil Manufacturing model SWA-48 pallet wrapper. 48″ diameter turntable. One film rod. 10″ and 20″ spacer. Foot control. With weight scale and digital controls
-
Stock#: 17543
USED JET 1100 LB CAPACITY CHAIN HOIST
One (1) used Jet model 1/2SS-1G-10 chain hoist. Rated at 1100-pound lift capacity and at 14 feet per minute with a 10′ high lift. Includes manual trolley and pendulum controls. 115 volts
2 Availalbe
-
Stock#: 17539
USED MOVINGCOOL PORTABLE AIR CONDITIONER
One (1) used MovinCool Model 15SFU-1 spot industrial portable air conditioner. Caster mounted. Rated at 15,000 BTU cooling capacity. Good to 104 degrees f. Uses 1.9 pounds of R-22 refrigerant. Two cooling discharge ports.. Weighs 167.2 pounds. 230/1/60. 9.8 FLA
3 Available – two 15,000 BTU and one 10,000 BTU
-
Stock#: 17494
USED VACUUM SHREDDED PAPER & DUST COLLECTOR
Dust / shredded paper & dust vacuum collector, Model 3925Z208CV, S/N P98H07728, 120-Volts 14 peak Amps, 2″ OD take off vacuum port and 2″ OD exhaust port, motor over drum design
-
Stock#: 17423
USED PURITAN VERTICAL SPOUT MAGNET
Puritan model VS288EZ vertical spout magnet having a 3.5″ inlet and outlet. Stainless steel construction. Engineered to remove fine to large ferrous contaminants from high volume, gravity fed product streams. Puritan’s Vertical Spout Magnets are ideally suited for products that would bridge or choke in a magnetic tube type separator. Ferrous contaminants are easily removed from products that are moist, lumpy, granular, or in powder form.
Vertical Spout Magnets consist of a housing and two opposing Plate Magnets. A center diverter on the housing inlet helps direct product towards the magnets. Ferrous contaminants are pulled from the flowing product and are captured by the powerful magnets. A Single Trap face design eliminates the possibility of the captured tramp metal being washed off back into the product stream.
Cleaning is achieved by releasing the latch assembly and pulling the drawer open. As the drawer is opened the magnets remain in a stationary position. Ferrous contaminants are transferred outside the product flow area where they are safely discarded. A specially designed angled drawer end ensures all contaminants are released outside of the product flow area. As product enters the stainless-steel housing, it is diverted towards two very large and powerful magnets that oppose each other. A Single Trap face design eliminates the possibility of contamination wash-off.
-
Stock#: 17245
USED SESOTEC FS70 METAL SEPARATOR
Sesotec model Rapid-Vario FS70 metal separator, S/N 1001-3668-PP, 2016 model year, aluminum in-feed hopper, Primus+ touch pad controls, 110/240 volt input, two (2) 3″ OD discharge outlets. 0.60mm ferrous, 0.96mm non-ferrous, and 1.20mm stainless steel sensitivities.
-
Stock#: 17246
USED SEARCH & SEPARATE COMPACT 70 METAL SEPARATOR
Search & Separate model Rapid Compact 70 metal separator, S/N 2004-10-3787, 110/240 volt input, two (2) 3″ OD discharge outlets. 0.60mm ferrous, 0.96mm non-ferrous, and 1.20mm stainless steel sensitivities, in-feed funnel is missing. Up to 5,000 Lbs. per hour capacity dependent on the flow and density of the bulk material.
-
Stock#: 17208
USED 2.5″ OD BIN AUGERS
Pair of 2.5″ bin augers each powered by a 3/16 HP 90 volt DC motor with a 5:1 gear ratio, 10″ diameter flange mounts, includes controls and level switches.
-
Stock#: 17209
USED BUNTING MAGNETICS 2.5″ OD IN-LINE MAGNET
Bunting magnetics 2.5″ OD in-line magnet part #936270-1
-
Stock#: 16866
USED ERIEZ MAGNETICS EZ TECH 9100 METAL SEPARATOR
Eriez magnetics metal separator model E-Z Tec 9100, S/N 79140.11, 115-Volt, single phase operation. 70mm inlet gravity free fall feed.
-
Stock#: 16670
USED AHLSTROM F4 PRESS SCREEN BASKET WITH 0.006″ SLOTS
Ahlstrom F4 press screen basket with 0.006″ slots.
-
Stock#: 16323
USED KONGSKILDE POLYVAC 20
Kongskilde model Polyvac 20, S/N 0076. 3HP 230/460V blower motor OK160 (6″) inlet, 3/4HP airlock. Includes gaylord height stand with 59″ wide x 57″ tall opening.
-
Stock#: 10821
USED AEC POWDER BAG BREAK STATION
AEC powder bag break station, 40″ x 40″ x 34.5″, 10 cubic foot capacity hopper. 1/2″ rod with 3″ spaced grating, 14 gauge steel bag cutter, 12 gauge carbon steel overall construction. Includes optional 1.5HP 3,450 RPM exhaust blower and 3 port vacuum distribution box with one 1.25″ ID vacuum take off. Station is in like new condition.
-
Stock#: 12096
USED MILLENNIUM INDUSTRIES MODEL HS9100 METAL SEPARATOR
Millennium Industries model HS9100 metal separator, S/N 9910080-57098. 110/230V / 1ph / 60Hz operation. Approximately 9.5″ diameter x 8″ deep in-feed bowl. Unit requires compressed air to operate the diverter.