-
Stock#: 17333
USED CALIFORNIA PELLET MILL CONDITIONER
One (1) California Pellet Mill conditioner for use with a pellet mill. Mixing section measures approximately 28″ in diameter x 8′ long. Unit is belt driven by approximately a 15 HP motor through a gear reducer
-
Stock#: 17329
USED CHAMPION 20″ X 44″ HAMMER-MILL
One (1) used Champion model 20″ x 44″ Magnum hammer-mill. Unit has 2,400 cubic inches of screen area with a 3/16″ screen installed. 200 HP 1800 RPM motor supplies a 20,730 RPM tip speed. 44″ diameter rotor. Serial number 102396. 460/3/60, 230 amps.
-
Stock#: 17322
USED COLORADO MILL EQUIPMENT C5 PELLET COOLER
Colorado Mill Equipment model C5 pellet cooler (now replaced by the c6). Rated at 3 to 6 tons per hour of pellets depending on pellet size, density, temperature and composition. Unit has a nominal 55″ x 55″ variable swing discharge grid with a dwell time of 10 to15 minutes. Includes optional cyclone with 17″ inlet and 11″ outlet, 15 HP blower, screener, and top airlock with a 10″ x 12″ entrance and 1 HP motor with gearbox. limited use. extremely clean.
-
Stock#: 17319
USED SPROUT WALDRON SW26 PELLET MILL
One (1) used Sprout Waldron model 26 pellet mill having a 26″ diameter die with ¼” holes. Unit was recently rebuilt and was used for test runs on wood pellets and alfalfa. 11″ x 13″ feed entrance with 5 HP feeder. Conditioner is mounted over the pellet mill and has a 10 HP drive and discharges into the feed entrance of the mill. Unit is direct driven by a 300 HP A/C motor with Motortronics VMX series soft start. extremely clean. serial number 82-244. 460/3/60 operation.
-
Stock#: 17224
NEW / UNUSED LOT OF 5 STAINLESS BRAIDED WATER LINES
Midwest Flexible Hose Co stainless steel braided water lines, New / unused condition Lot of 5 hoses, all 2-3/4″ ID, one 6′ long, one 9′ long, two 10′ long, and one 11′ long
-
Stock#: 17245
SESOTEC FS70 METAL SEPARATOR
Sesotec model Rapid-Vario FS70 metal separator, S/N 1001-3668-PP, 2016 model year, aluminum in-feed hopper, Primus+ touch pad controls, 110/240 volt input, two (2) 3″ OD discharge outlets. .60mm ferrous, .96mm non-ferrous, and 1.20mm stainless steel sensitivities.
-
Stock#: 17234
USED LINDBERG / BLUE LAB OVEN
Lindberg / Blue lab oven model G01310A, S/N P18H-373672-RH, 12″ x 12″ x 12 (1 cubic foot) inside, 260 maximum degrees Celsius, 40 degrees Celsius minimum, two tray racks
-
Stock#: 17146
USED MAGNETEK VCD703 250 HP A/C DRIVE
MAGNETEK MODEL VCD703 A/C INVERTER DRIVE, 250 HP A/C, 345 FLA, 460/3/60, MOUNTED IN DAVIS STANDARD DOUBLE DOOR CONTROL CABINET, WAS DRIVING 4.5″ DAVIS STANDARD EXTRUDER
-
Stock#: 17135
USED ROSENTHAL 48″ SHEETER
ROSENTHAL MODEL “WRAP-O-MATIC” WA-S-4-U, S/N 51296, 48″ WIDE SHEET, 2 HP DRIVE MOTOR, 120 VOLT OPERATION
-
Stock#: 16235
USED ROSENTHAL 60″ SHEETER
USED ROSENTHAL WRAP-O-MATIC MODEL WA-S5UZTEVAB 60″ WIDE SHEETER, S/N 51846, 120 VOLT OPERATION VOLTAGE, 12 MAXIMUM AMPS, INCLUDES BOX OF MISCELLANEOUS SPARE PARTS
-
Stock#: 17123
USED APPLETON P510 AUTOMATIC CORE CUTTER
APPLETON MODEL P510 CORE CUTTER, S/N 12.06.12, 132″ LONG PROGRAMMABLE AUTOMATIC CORE CUTTER WITH 4-15/16″ DIAMETER MANDREL, IDC (INSTANT DIAMETER CHANGE) FOR ONE MINUTE CHANGEOVER, 6.5″ AND 6.75″ DIAMETER CARBON FIBER MANDREL SLEEVE, AUTO CORE PUSHER, AUTO CORE ADVANCEMENT VIA SERVO BALL SCREW DRIVE, OPERATOR CONTROL STATION WITH ALLEN BRADLEY PANEL VIEW HMI CONTROLS, SAFETY GUARDING, 480/3/60 INPUT POWER, INCLUDES SOME TOOLING, 2012 MODEL YEAR, REPORTED IN EXCELLENT CONDITION
-
Stock#: 17023
USED FITZPATRICK DASO 6 FITZMILL
USED FITZPATRICK DASO 6 FITZMILL. S/N 11303, STAINLESS STEEL CONSTRUCTION. UNIT FED BY K-TRON MODEL K-2 VOLUMETRIC FEEDER. FIXED KNIFE ROTOR. ROTOR IS BELT DRIVEN BY 7.5 HP MOTOR WITH EXPLOSION PROOF CONTROLS. MOUNTED ON A STAND WITH CASTERS ALLOWING FOR A DRUM HEIGHT DISCHARGE. INCLUDES STARTER AND CONTROLS FOR FEEDER AND FITZMILL. 460/3/60. S/O NUMBER 8627
-
Stock#: 17022
USED JH DAY FA3.5 NAUTA MIXER / DRYER
USED 3.5 CUBIC FOOT JH DAY MODEL FA3.5 NAUTA MIXER / DRYER, 304 STAINLESS STEEL CONSTRUCTION, RATED VACUUM INTERNAL AT 353 DEGREES F. JACKETED FOR 125 PSI AT 353 DEGREES F. 5 HP DRIVE THROUGH A GEAR REDUCER. MOUNTED ON LEGS. SERIAL: 42408-1759. MANUFACTURED 1988. DAY CERTIFICATION # 1759
-
Stock#: 17016
USED LINDBERG BLUE M LAB SIZE OVEN
LINDBERG / BLUE M LAB SIZE OVEN, 16″ X 22″ X 15″ INSIDE DIMENSIONS, WITH TWO RACKS AND POWER CORD
-
Stock#: 17005
USED THERMOWARE PRE-EXPANDER / FLUID BED DRYER COMBINATION
ONE (1) USED THERMOWARE PRE-EXPANDER / FLUID BED DRYER COMBINATION. PACKAGE CONSISTS OF A MODEL VA 80 PRE-EXPANDER WITH A MODEL FB 80 FLUID BED DRYER. OUTPUT IS RATED TO 80 KGS / HOUR. USING THE PRE-EXPANDER, IN COMBINATION WITH FLUIDIZED BED IT PRODUCES EPS GRANULES ARE IN PERFECT SHAPE AND SIZE FOR THE PRODUCTION OF THIN WALLED PACKAGING PRODUCTS, LIKE FOR INSTANCE CUPS AND TRAYS. MANUFACTURED 2013. VA 80 SERIAL NUMBER: 12176 1107. FB 80 SERIAL NUMBER 12176 1408
-
Stock#: 17012
USED PROCEDYNE PCF2430-FB THERMAL PART CLEANING SYSTEM
ONE (1) USED PROCEDYNE MODEL PCF2430-FB THERMAL PART CLEANING SYSTEM. S/N 1827-00255, 24” X 30” BASKET FOR PARTS. CLEANING SYSTEMS IS DESIGNED TO REMOVE COATINGS FROM ALL TYPES OF HARDWARE AND PARTS – WITH NO CARBON RESIDUE. ABSOLUTE TEMPERATURE CONTROL AND THERMAL UNIFORMITY PERMITS CLEANING OF COMPLEX CRITICAL HARDWARE WITH MINIMAL RISK OF DISTORTION OR METALLURGICAL DAMAGE. NATURAL GAS FIRED 400,000 BTU BURNER. WITH CONTROLS, CYCLONE AND OPTIONAL PROCEDYNE MODEL AB-25-1 AFTERBURNER, S/N 1627-00255, 120 VOLT SINGLE PHASE OPERATION, AFTERBURNER CAPACITY IS 15 LBS PER HOUR AT PEAK RATE
-
Stock#: 16814
USED CARVER HYDRAULIC PRESS
CARVER MODEL 19200-197 MANUAL HYDRAULIC PRESS, TWO 6″ X 6″ ELECTRICALLY HEATED PLATENS, ADJUSTABLE DAYLIGHT
-
Stock#: 16733
USED BERINGER MINI JET BURN OUT OVEN
BERINGER MODEL MINI JET CLEANER, S/N JA1003, 460/3/60 OPERATION, 8.2 KVA MAXIMUM LOAD, 950 DEGREES MAXIMUM TEMPERATURE, APPROXIMATE 9″ X 9″ PARTS BASKET, MANUFACTURED 3/2000
-
Stock#: 16671
USED AHLSTROM F4 PRESS SCREEN MAIN SHAFT
AHLSTROM F4 PRESS SCREEN MAIN SHAFT
-
Stock#: 16660
USED AHLSTROM F4 PRESSURE SCREEN
AHLSTROM MODUSCREEN F4 PRESSURE SCREEN, 0.006″ CONTOURED SLOTS, 85 PSI MAXIMUM INLET PRESSURE, 1918 GPM DESIGN FLOW, 2550 GPM MAXIMUM FLOW, 9% REJECT RATE BY VOLUME, 15% REJECTION RATE BY WEIGHT, RATED AT UP TO 600TPD (2% – 5% CONSISTENCY), 100 HP TECO MOTOR, 575/3/60, SPARE BASKET AND SPARE SHAFT ASSEMBLY AVAILABLE SEPARATELY – STOCK NO’S. 16670 AND 16671