One (1) used Gala model 5MUP underwater pelletizing system. Includes 2 HP cutter with four (4) blade hub, three (3) spare dies, 40 GPM TWS-40 water system with heater, pump, heater exchanger, 5 HP model 8.2 BF dryer, and non-OEM custom control panel. S/N 8801458
Sheer Bay Plastics Machinery Model SGS-300-A 12″ strand pelletizer. S/N SA305-003. Dual motor driven by approximate 15 HP rotor motor and 10 HP pull roll motor. 460/3/60 A/C input. Includes 60 knife helical rotor installed. Includes spare sharpened 60 knife rotor as well as the manual and three (3) spare rubber rolls. Good condition.
One (1) used AET model 45AS32 4.5″ 32:1 L/D extruder having a six (6) zone electrically heated, water cooled (closed loop), and side vented barrel at a nominal 42″ center-line height. The gearbox is direct driven out the back end by a 250 HP Marathon Blue Max motor with inverter. The gearbox has a shaft mounted oil pump and heat exchanger. The extruder has a water-cooled feed throat. The free-standing temperature control panel has six (6) zones for the barrel and three (3) zones of temperature controls for downstream zones. Inverter is mounted inside the control panel. 480/3/60 600 amps. S/N 2448. Manufactured 11-04-04. Includes Nordson/Xaloy model EH-60 hydraulic slide plate screen changer having two (2) nominal 6″ diameter breaker plates, hydraulics, and accumulator. Also includes Nordson/Xaloy model WRP-12I water ring pelletizing system. Still Installed and running until 7/2022.
One (1) used incomplete CDL model UWP36620 underwater pelletizing system. Includes 20 HP cutter less cutting hub, 48 hole electrically heated die, and water tempering system including pump, reservoir, and heated exchanger. S/N DB06. Job number J1871
Used 6″ Cumberland Quietizer pelletizer. S/N 3260503-85002. Driven by approximately a 5 HP D/C motor with SCR. Has sixteen (16) knife rotor with removable blades. Air actuated nip rolls. Sound enclosed. Caster mounted.
Used Gala underwater pelletizing system new 2004. System consists of the following:
– PAK7 underwater pelletizer including operator control panel. 380 volt, 50 Hz AC input.
– Electric heated die plate and SS water chamber
– Gala water tempering system Model TWS-480, rated at 480 gallons per minute. Includes pump, heat exchanger and reservoir tank
– Gala spin dryer Model 3016DW including agglomerate catcher.
Used 4″ wide Scheer Bay pelletizer Model SGS100-E. S/N SE10CC-9801, 460 volt A/C input, 3 phase, 60 hertz, 14.2 amps. Has 32 knife carbide inlay helical style rotor driven by an AC Tech variable speed controller. Mounted on caster base.
One (1) used Gala model 5 underwater pelletizing system, includes 2 HP cutter, two (2) 12-hole dies, one (1) die with nano holes, 20 GPM water system with heater, pump, heater exchanger, 3 HP model 8.1 BF dryer, and free-standing control panel. Also includes four (4) spare cutter assemblies. S/N 85022. very clean.
Used 8″ Cumberland Quietizer pelletizer. Serial #264550-98005. Driven by 15HP AC motor, with variable frequency drive, 460-Volt AC input. Has 48 knife helical style rotor, air cylinder actuated nip rolls. Includes spare helical rotor.
Cumberland Utilizer 6″ strand pelletizer. Machine has a 36 knife helical style rotor and a 5HP 180-Volt DC motor with silicon controlled rectifier control. Mounted on casters, S/N 30500-88004. Manufactured 1988. 220V/1ph/60Hz operation.
One (1) used Automatik / Gala model Sphero 220.1 underwater pelletizing system. Unit is rated for up to 22,000 pounds per hour. Order number 1019020. Machine number SH-204. Manufactured in 2013. 460V/3ph/60Hz operation.
The system consists of the following components:
A) Hydraulically actuated start up value with 11 kW hydraulic pump.
B) Liquid heated die plate with Sterlco model M2B6017-L 100 kW oil heater.
C) A 60HP 36 knife cutter head with a pneumatically adjustable knife shaft.
D) A cutting chamber with tangential water supply and pellet drain.
E) A Movitec model VSF 90/4-2B water tempering system with a FUNKE plate type heat exchanger
F) A 7.5HP spin dryer with an agglomerate catcher and a 1.5HP blower.
G) A free standing control panel. H) A support structure for the cutter cutting chamber, hydraulic pump, hydraulic vale, and operator controls.
Scheer Bay Company model B20-P long fiber pelletizer, S/N B20P-0103. 20″ wide angle cut 6 knife rotor with two 10″ wide knives per position. 460V/3ph/60Hz operation, complete with a stand-alone control panel. A spare rotor with knives installed is also available.