Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => pelletizing-lines [3] => just-arrived [4] => extruders-twin-screw [5] => pelletizing-lines )
  • Stock#: 17395

    USED LEISTRITZ/GALA 27mm COMPOUNDING LINE


    Leistritz / Gala 27mm compounding line consisting of the following components:

    One 27mm 40:1 Leistritz model Micro 27 40GL/40D twin screw extruder with co-rotating inter-meshing screws. Barrel is electrically heated, water cooled and consists of nine (9) barrel sections. Gearbox is direct driven by a 10.5 KW (14.3 HP) DC motor with SCR (silicone controlled rectifier) allowing for an approximate maximum screw speed of 500 RPM. Integral movable control panel has eleven (11) zones of temperature control and all operator controls. Includes pre-polymer metering pump and three (3) sets of screw shafts with loose screw elements. Manufactured in 1997. S/N 2553. Pulled from service in January of  2021. Gala model 6PDV polymer diverter valve with 10 HP hydraulic pump. Unit is used until the extruder is up to speed. Gala model SLC6 underwater pelletizer with 4.3 KW (5.3 HP) spring loaded cutter, model 40TWS water tempering system with heated reservoir, 3 HP water pump, heat exchanger, Gala model 8.1BF spin dryer with agglomerate catcher and free-standing control panel with touch screen controls. Offered less die. Includes spare blades, heater bands, and manuals. 460V/3ph/60Hz 46 FLA operation . Manufactured in 2000. S/N 10100743.

  • Array ( [0] => pelletizing-lines [1] => pelletizing-lines )
  • Stock#: 17124

    USED DAVIS STANDARD EXTRUDER / PELLETIZING LINE


    Pelletizing line consisting of one 4.5″ 24:1 Davis Standard model 450H7214 extruder. Five (5) zone electrically heated or water cooled and side vented barrel at approximately a 42″ center-line. Heavy duty gearbox has a reduction ratio of 17.21:1 and is rated at 147HP at a service factor of 1.5. Gearbox is belt driven by a 300HP DC motor with SCR control. CV clamp on barrel discharge. Includes gravity feed hopper and free-standing control panel. S/N CE4265. Also includes one (1) used slide plate screen changer with two (2) nominal 4.5″ diameter breaker plates and a Berringer model WRP12 water ring pelletizing system with 2HP cutting head. 80 hole die tempered water system with heat exchanger sluice gate and a 5HP centrifugal spin dryer.


  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-lines [3] => just-arrived [4] => pelletizers [5] => pelletizing-lines )
  • Stock#: 17001

    USED AUTOMATIK / GALA MODEL SPHERO 220 UNDERWATER PELLETIZING SYSTEM


    Automatik / Gala model SPHERO 220 underwater pelletizing system. Unit is rated at up to 22,000 pounds per hour. Machine serial number 1018144-SH-117. Manufactured in 2010. 460V/3ph/60Hz operation.

    The system consists of the following components:

    A) Hydraulically actuated start up value with an 11 kW hydraulic pump.

    B) Liquid heated die plate with a Sterlco model M2B6017-L, 80 kW oil heater.

    C) A 60HP, 36 knife cutter head with a pneumatically adjustable knife shaft.

    D) A cutting chamber with a tangential water supply and pellet drain.

    E) Movitech model VSF90/4-2B water tempering system with a FUNKE model plate type heat exchanger.

    F) A 7.5HP spin dryer with an agglomerate catcher and a 1.5HP blower motor (missing the motor).

    G) A free-standing control panel.

    H) A support structure for the cutter, cutting chamber, hydraulic pump, hydraulic vale, and operator controls.

    Last used on EPS micro beads.

  • Array ( [0] => pelletizers [1] => pelletizing-lines [2] => pelletizers [3] => pelletizing-lines )
  • Stock#: 17002

    USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM


    One (1) used Automatik / Gala model Sphero 220.1 underwater pelletizing system. Unit is rated for up to 22,000 pounds per hour. Order number 1019020. Machine number SH-204. Manufactured in 2013. 460V/3ph/60Hz operation.

    The system consists of the following components:

    A) Hydraulically actuated start up value with 11 kW hydraulic pump.

    B) Liquid heated die plate with Sterlco model M2B6017-L 100 kW oil heater.

    C) A 60HP 36 knife cutter head with a pneumatically adjustable knife shaft.

    D) A cutting chamber with tangential water supply and pellet drain.

    E) A Movitec model VSF 90/4-2B water tempering system with a FUNKE plate type heat exchanger

    F) A 7.5HP spin dryer with an agglomerate catcher and a 1.5HP blower.

    G) A free standing control panel. H) A support structure for the cutter cutting chamber, hydraulic pump, hydraulic vale, and operator controls.

    Last used on EPS micro beads.

  • Array ( [0] => pelletizers [1] => pelletizing-lines [2] => pelletizers [3] => pelletizing-lines )
  • Stock#: 17003

    USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM


    Automatik / Gala model Sphero 220.1 underwater pelletizing system. Unit is rated up to 22,000 pounds per hour. Order number 1019020. Machine number SH-205. Manufactured in 2013. 460V/3ph/60Hz.

    The system consists of the following components:

    A) A hydraulically actuated start up value with 11 kW hydraulic pump.

    B) A liquid heated die plate with a Sterlco model M2B6017-L 100 kW oil heater.

    C) A 60HP 36 knife cutter head with a pneumatically adjustable knife shaft

    D) A cutting chamber with a tangential water supply and pellet drain.

    E) A Movitec model VSF 90/4-2B water tempering system with a FUNKE type plate heat exchanger.

    F) A 7.5HP spin dryer with an agglomerate catcher and a 1.5HP blower.

    G) A free standing control panel.

    H) A support structure for cutter, cutting chamber, hydraulic pump, hydraulic vale, and operator controls.

    Last used on EPS microbeads.

  • Array ( [0] => pelletizers [1] => pelletizing-lines [2] => pelletizers [3] => pelletizing-lines )
  • Stock#: 16563

    USED PRODEX 6″ EXTRUSION PELLETIZING LINE


    Pelletizing line consisting of the following components:

    A) Prodex model TM-600-30 6″ 30/1 extruder with six (6) closed loop, electrically heated and water cooled zones. Side vented barrel at an approximately 42″ centerline. Includes a 3HP centrifugal water vacuum pump for the vent. Unit has a Prodex / Lufkin model TMH-60A-315 change gear box with 10.4:1 gears installed. Gearbox is direct driven by a 400HP Emerson DC motor with ABB model DCS-800 digital SCR control. 400HP DC motor was cleaned and baked in 2017. Stand-alone temperature control panel with 12-zones. Digital controllers set up for six (6) barrel three (3) screen changer and two (2) die zones. Extruder is set up for a crammer feeder and includes an adapter.

    B) Xaloy model EH-80 slide plate screen changer with two (2) nominal 8″ diameter breaker plates with model HPU-50 5HP hydraulic pump power pack and controls. Manufactured in 2008. Screen changer serial number is EH80059.

    C) Berringer model WRP12 water ring pelletizing system with a 3HP cutting head, 5HP centrifugal dryer, and tempered water recirculation system with a 5HP pump.

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-lines [3] => recycling [4] => just-arrived [5] => pelletizers [6] => pelletizing-lines [7] => recycling )
  • Stock#: 16115

    USED EREMA KAG800/63 LDPE/LLDPE 400 LBS/HR FILM RECLAIM LINE


    Erema model KAG800/63 IDPE / LLDPE film reclaim line consisting of the following components:

    A) Model 5000/600 inclined cleated conveyor measuring 23.6″ wide x 16.4′ long with model DLS840/600/400 metal detector.

    B) 800mm (31″) diameter integral densifier / agglomerater with a 40HP drive infeed hopper. Includes conveyor and pull roll feed and a SAS1500 moisture and fines removal system.

    C) 63 mm 7:1 L/D ratio air cooled extruder with 20 HP AC motor with invertor and control panel for the entire system. S/N P04/172

    D) Model HGL hot cut pelletizer with pellet cooling blower and cyclone.

    Line was manufactured in 2005 and is rated for 400 pounds per hour throughput.