Array ( [0] => pipe-profile-pullers [1] => pipe-profile-pullers )
  • Stock#: 17669

    USED GOODMAN 6″ X 30″ BELT PULLER


    Goodman profile belt puller, S/N 6860, 6″ wide x 30″ belt contact area at a 41″ center line height, but adjustable. Belt hand tensioning crank. Driven by a 2 HP 1725 RPM 230/460-volt Baldor vector drive motor, 240/3/60 input power, 9 maximum amps, Goodman controls, mounted on casters, 770 Lbs. Very clean nice unit.

    Add to QuoteDetails
    • Array ( [0] => pipe-profile-pullers [1] => pipe-profile-pullers )
  • Stock#: 16648

    USED GOODMAN 6″ X 30″ PULLER


    G.F. Goodman & Sons profile belt puller, S/N 5454. 6″ x 30″ belt, 42″ centerline, 480V/3ph/60Hz input, 4 amps maximum load. Belt powered by a 3HP 1,750 RPM DC motor with brush less DC drive unit. 30:1 gearbox encoder, digital line speed read out, leveling screws, manual raise and lower, 7.5″ tall. Maximum part height 43″ x 32″ x 72″, approximately 1,000 Lbs.

    Add to QuoteDetails
    • Array ( [0] => pipe-profile-cutters [1] => pipe-profile-pullers [2] => pipe-profile-cutters [3] => pipe-profile-pullers )
  • Stock#: 16931

    USED RDN 3″ X 23″ BELT PULLER / CUTTER


    RDN Manufacturing model EMC2DC2183 belt puller / cutter, S/N 24754. 3″ x 23″ belt area, 2 blade cutter, manual wheel belt height adjustment. 460V/1ph/60Hz operation. Cutter is powered by a 1.5HP DC motor. 1/2″ diameter profile hole length counter monitor and speed indicator. Mounted on casters with adjustable height pads. Measures 74″ x 42″ x 77″ tall. Weight is approximately 1,504 Lbs. Manufactured in January 1989.

    Add to QuoteDetails
    • Array ( [0] => pipe-profile-pullers [1] => pipe-profile-pullers )
  • Stock#: 16867

    USED CONAIR 4-26 BELT PULLER


    Conair model 4-26 belt puller, S/N 951525. 4″ x 26″ belt contact area, powered by a 1.5HP single phase motor, 5.2 maximum amp load, adjustable vertical belt spacing. Includes Fenner digital controls. Mounted on adjustable height mounts.

    Add to QuoteDetails
    • Array ( [0] => pipe-profile-pullers [1] => pipe-profile-pullers )
  • Stock#: 16051

    USED MERRITT DAVIS 8″ X 108″ BELT PULLER


    Merritt Davis model 80 belt puller, S/N WC04415-23. 460V/3ph/60Hz operation. 8″ wide x 108″ belt contact area. Top and bottom belts are driven by a drive shaft from an approximately 15HP motor with a manual hand crank gap adjustment with air cylinder pressure. Includes a variable frequency drive.

    Two are available.

    Add to QuoteDetails
    • Array ( [0] => pipe-profile-pullers [1] => pipe-profile-pullers )
  • Stock#: 2677

    USED ACCU-PULL 4″ X 2″ PULL ROLLER


    Accupull roll puller with 4″ diameter x 2″ wide polyurethane rolls. 240V/1ph/60Hz operation.

    Add to QuoteDetails
    • Array ( [0] => pipe-profile-pullers [1] => pipe-profile-pullers )
  • Stock#: 10358

    USED HOSE PULLER 1 HP


    Hose puller 1HP motor driven through a gearbox timing belt. Drives a 3.5″ x 6″ long roll with idler roll and hose guide.

    Add to QuoteDetails
    • Array ( [0] => pipe-profile-pullers [1] => pipe-profile-pullers )
  • Stock#: 14985

    USED CONAIR 4-26 PROFILE PULLER


    Conair model 4-26 puller, S/N 88667. 4″ x 26″ belt contact area powered by two 2.1HP MTS Automation servo motors, Powertec Digimax touchpad controls. Each servo motor driven by a brushless torque follower drive, brushless cutter drive. Mounted on casters and adjustable height pad stands.

    Add to QuoteDetails
    • Array ( [0] => used-equipment [1] => pipe-profile-pullers [2] => used-equipment [3] => pipe-profile-pullers )
  • Stock#: 6693

    USED FARRIS TYPE 550 CHVT BELT PULLER


    Farris type 550 CHVT horizontal profile puller, S/N 3036. 4.5″ x 28″ contact area belt for up to a 6″ wide profile. 1.5 feet per minute to 227 feet per minute range. 5HP Reliance DC motor arranged through a gear box. Manual open and close.

    Add to QuoteDetails
    • Array ( [0] => pipe-profile-cutters [1] => pipe-profile-pullers [2] => pipe-profile-cutters [3] => pipe-profile-pullers )
  • Stock#: 2018

    USED VERSA 45W PULLER / CUTTER


    Versa model 45W cutter / puller, S/N 45067. Zero to 2-1/4″ OD capacity, digital readout, adjustable pull rolls, hour meter, and a 2HP drive motor.

    Add to QuoteDetails
    • Array ( [0] => used-equipment [1] => pipe-profile-pullers [2] => used-equipment [3] => pipe-profile-pullers )
  • Stock#: 12089

    USED BOSTON MATHEWS 3″ WIDE X 23″ LONG BELT PULLER


    Boston Mathews 3″ wide x 23″ long belt puller, S/N E-000-VT/1422A. 1HP 180V 1,750 RPM DC motor into a gearbox with an air operated belt pinch mounted on an adjustable height pad. No speed control is included.


    Add to QuoteDetails
    • Array ( [0] => used-equipment [1] => pipe-profile-pullers [2] => used-equipment [3] => pipe-profile-pullers )
  • Stock#: 12792

    USED GATTO MODEL 210-6P PROFILE PULLER


    Gatto model 210-6P profile puller, S/N 776955. 6″ x 36″ belt driven by a 3HP 180V 1,750 RPM DC motor through two gearboxes.

    Add to QuoteDetails
    • Array ( [0] => used-equipment [1] => pipe-profile-pullers [2] => used-equipment [3] => pipe-profile-pullers )
  • Stock#: 12954

    USED 6″ WIDE X 28″ LONG CONTACT AREA BELT PULLER


    Farris 6″ wide x 28″ long contact area belt puller, 2HP 230/460V gear motor. 14 to 34 feet per minute. Includes Dayton AC power inverter, complete with controls.

    Add to QuoteDetails
    • Array ( [0] => used-equipment [1] => pipe-profile-pullers [2] => used-equipment [3] => pipe-profile-pullers )
  • Stock#: 14540

    USED AMERICAN MAPLAN / BATTENFELD MODEL P160BVE PROFILE PULLER


    Battenfeld-Cincinnatti USA model vacuum calibration tank with water spray cooling, S/N 33601-01. Machine no. 3495 machine type V1-110-4.0W 460V/3ph/60Hz operation, 20 amps maximum draw. 158″ long by approximately 11″ diameter tank with clear view ends. 1.75 kW vacuum pump, 3.45 kW water circulation pump. 0.37 kW track motor, 110mm (4″) maximum profile diameter with starters and controls. Includes 154″ of track for track casters on a unitized base.

    Add to QuoteDetails