Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17345

    LOW HOURS LINDNER L1100 SHREDDER SYSTEM


    Little used Lindner shredding system (2011) with approximately 50 hours of use. System includes the following:

    A. Hydraulic bin tipping unit with safety cage.

    B. 700mm (27.5″) wide in feed conveyor with 2,000mm (6’5″) long straight section and 4,500mm (14’6″) incline section at 30 degrees. 1,500mm (4’8″) long horizontal discharge section. Conveyor is chain driven with PVC belt and 76mm (3″) chain pitch. Variable speed with controls.

    C. Model Vega L1100 single shaft shredder having an 1,100mm (43.3″) wide entrance with a 48 knife rotor. 1,080mm x 1,124mm throat opening (42″ x 44″). Voltage is 400/3/50 – 460/3/60 input. Rotor is belt driven by a 55 KW (71.5 HP) drive at 50 Hz or 63 KW (81.9 HP) drive at 60 Hz. Last used on 400/3/50. 50mm screen installed. PLC controlled. S/N 1630

    D. 700mm (27.5″) wide discharge conveyor with 2,000mm long straight section and 8,000mm long inclined section. Variable speed with controls.

    Located in the United Kingdom

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17311

    USED UNTHA RS40 FOUR SHAFT SHREDDER / GRANULATOR LINE


    Untha RS40 4 Shaft Shredder / Cumberland 484 Shredder / Granulator Line

    A) New London incline conveyor having a 30″ wide x 14′ long belt with 1″ cleats on a 12″ center-line. caster mounted.

    B) Untha model RS40 four shaft shredder. unit has a 32″ x 26″ throat opening on a 48″ high leg base. hopper entrance measures 39″ wide x 32″. Rotors have a total of seventy-four (74) ¾” thick cutters. Rotors are driven by dual 15 hp motors. in-feed height to shredder is 94″.

    C) Shredder discharges into an Eriez style 824965 drum magnet. Housing measures 15″ x 18″. S/N 92312.

    D) Material from the drum magnet is discharged into a New London model 590-24″-66″ belt conveyor and has a 24″ wide x approximately 18′ long belt. Belt has 2″ cleats and discharges at a height of 9′.

    E) Conveyor feeds a Cumberland model 484 granulator having a 14″ x 16″ throat opening with a three (3) knife open rotor. Rotor is belt driven by a 25 HP motor.

    F) Includes controls to operate each piece of equipment. Very good condition. Last used to recycle plastic coat hangers.

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17214

    USED VECOPLAN RG52/100SPK SHREDDER


    VECOPLAN MODEL RG52/100SPK SINGLE SHAFT SHREDDER, S/N 8124010, 2005 MODEL YEAR, 15″ DIAMETER ROTOR WITH 60 PC DOUBLE ROW OF BOLT ON 40mm INDEX ABLE CUTTERS, ROTOR IS POWERED BY A 63 KW (85 HP) 480 VOLT MOTOR, HYDRAULIC POWERED RAM, ORIGINAL OEM 480V TOUCH SCREEN CONTROL PANEL, 2″ HOLES SCREEN, INCLUDES 25′ LONG IN-FEED CONVEYOR WITH 41″ WIDE FLAT BELT AND 36″ TALL SIDE WALLS, POWERED BY A 2 HP 460 VOLT MOTOR, ALSO INCLUDES TAKE-AWAY CONVEYOR WITH 16″ WIDE BELT WITH 1.5″ TALL CLEATS 48″ ON CENTER AND IS 153″ TOTAL LENGTH, POWERED BY A 1 HP 460 VOLT MOTOR AND HAS MAGNETIC HEAD PULLEY

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17213

    USED SHRED-PAX AZ-80 TWIN SHAFT SHREDDER


    SHRED-PAX MODEL AZ-80 TWIN SHAFT SHREDDER, S/N 160-9216. 33″ X 63″ WIDE CUTTING CHAMBER ENTRANCE. CARBON STEEL CONSTRUCTION. TWO (2) ROWS OF INTER-MESHING KNIVES MEASURING 1-3/4″ THICK. EACH SHAFT IS DRIVEN BY A 40 HP 230/460-VOLT 1750 RPM SUMITOMO A/C MOTOR THRU A SM-CYCLO REDUCER. MOUNTED ON A STEEL FRAME. MANUFACTURED 1992. OVERALL DIMENSIONS 149″ X 53″ 94″. OFFERED LESS CONTROLS

  • Array ( [0] => shredders [1] => shredders )
  • Stock#: 17190

    USED SHRED-TECH ST10EL SHREDDER


    SHRED-TECH MODEL ST10EL SHREDDER, S/N E3480216, 13″ X 18 CUTTING CHAMBER WITH 5/8″ THICK 2 HOOK KNIVES, POWERED BY A 7.5 HP 460 VOLT MOTOR, 24″ X 29.5″ HOPPER OPENING, 126.5″ X 42″ FOOTPRINT WITH A HOPPER IN-FEED HEIGHT OF 103″, 30″ DIAMETER STAINLESS STEEL DE-WATERING TROMMEL DISCHARGE WITH 1/8″ WATER DRAINING HOLES, HOPPER, CHAMBER ENCLOSURE AND DE-WATERING TROMMEL ARE STAINLESS STEEL, INCLUDED CONTROL PANEL RUNS BOTH THE SHREDDER AND TROMMEL

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17172

    USED RAPID EH-52/37 100 HP SHREDDER


    RAPID (REPUBLIC MACHINE) MODEL EH-52-10-15-2-60-D (EH52/37) SHREDDER, S/N 760374916, 15″ DIAMETER X 52″ WIDE WATER COOLED ROTOR WITH 74 CUTTERS IN A DOUBLE ROW CONFIGURATION, 40mm CROWN CUTTERS WITH BOLT IN CUTTER HOLDER UPGRADE, POWERED BY A 100 HP 460 VOLT MOTOR, HYDRAULIC OPERATED RAM, 8″ OD AIRVEYOR DISCHARGE, BELT DRIVE THROUGH A GEAR BOX, 51.5″ X 42″ RAM AREA, 60.5″ LONG X 51.5 WIDE X 30″ TALL HOPPER, 121.5 X 90″ FOOT PRINT, 90.5″ OVERALL INSTALLED HOPPER HEIGHT, INCLUDES HYDRAULIC PUMP FOR THE RAM AND THE ORIGINAL OEM ALLEN BRADLEY COLOR TOUCH SCREEN CONTROL PANEL / DRIVE UNIT

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17048

    USED VECOPLAN V-ECO 1300 SHREDDER SYSTEM


    VECOPLAN MODEL V-ECO 1300 SHREDDER, S/N 12489 010, MANUFACTURED 2-12-15, 135 CUTTERS, (2) BED KNIFE POSITIONS – (1) ADJUSTABLE, 150 HP 460 VOLT MOTOR, ½” SCREEN – HAS 3/8″ SCREEN IN MACHINE, 3959 HOURS ON MACHINE, INCLUDES 35′ CONVEYOR, 3 HP DRIVE W/ BIG GEAR BOX – 43″ WIDE BELT – 2″ CLEATS ON 32″CENTERS, HOME MADE CUSTOM DEBRIS GUARD ENCLOSURE OVER THE TOTAL TOP OF THE SHREDDERS’ HOPPER “SEE PICTURE”, S & S METAL DETECTOR WITH 12″ HIGH CLEARANCE ABOVE BELT INCLUDES 6′ NONMAGNETIC SECTION BELOW BELTING, CUSTOM BUILT DROP OUT CHUTE POSITIONED BEFORE THE SHREDDER HOPPER TO CLEAN MATERIAL WITH METAL OFF CONVEYOR AND INTO BIN ON FLOOR, KICE 15 HP BLOWER WITH 8″ OUTLET TUBING RUNNING OVER TO 48″ DIAMETER CYCLONE RECEIVER THAT IS 7′ TALL. THE CYCLONE HAS “6” FILTER BAGS THAT HANG DOWN 8′. THE GAYLORD FILL DISCHARGE HAS A DRAWER MAGNET WITH RARE EARTH MAGNET BARS. WAS PROCESSING POST-CONSUMER JUGS & BOTTLES/POST-INDUSTRIAL SCRAP @ 3,000 LBS/HR, 90% POST-CONSUMER – 10% POST INDUSTRIAL

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 16964

    NEW SHRED TECH ST-25ES DUAL SHAFT SHREDDER


    NEW SHRED TECH MODEL ST-25ES DUAL SHAFT SHREDDER, S/N ST-25ES-F314, 2019 MODEL YEAR, 16″ X 14″ CUTTING CHAMBER, TWO HEXAGONAL COUNTER ROTATING SHAFTS, 5-7/8 SHAFT CENTER DISTANCE, 20 5/8″ WIDE X 7-3/4 DIAMETER TWO TEETH KNIVES, POWERED BY A 20 HP 480 VOLT GEAR REDUCED MOTOR, 21 RPM FAST SHAFT, 18 RPM SLOW SHAFT, 39,865 LBS MAXIMUM TOOTH FORCE, 31″ FROM FLOOR STAND TO STRADDLE DISCHARGE CUSTOMER SUPPLIED CONTAINER, 27″ X 29″ STANDARD FEED OPENING IN-FEED HOPPER, INCLUDES NEMA RATED CONTROL PANEL WITH PROGRAMMABLE LOGIC CONTROLLER AND FUSED LOCKABLE DISCONNECT

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 16963

    USED SSI M100E(63) DUAL SHAFT SHREDDER


    SSI MODEL M100E(63) DUAL-SHEAR TWO SHAFT SHREDDER, S/N S2175, SHREDDER IS EQUIPPED WITH 41″ X 63″ FEED OPENING AND DRIVEN BY 300 HP 1187 RPM 460 VOLT MOTOR. INCLUDES BREVINI GEAR DRIVE WITH A 29.3:1 REDUCTION RATIO. CUTTERS ARE 530MM DIAMETER (20.9″) AND MADE OF 4140 HT STEEL, DUAL SHAFTS WITH A 188MM (7.4″) SHAFT DIAMETER. CUTTERS ARE OF AN APPROXIMATE 9 TIP DESIGN. OFFERED LESS DRIVE UNIT OR WITH NEW WEG ELECTRIC 300 HP VARIABLE SPEED DRIVE IN NEMA 12 ENCLOSURE WITH DISCONNECT.

  • Array ( [0] => as-is-granulators-30-hp [1] => shredders [2] => as-is-granulators-30-hp [3] => shredders )
  • Stock#: 16665

    USED BALL & JEWEL SB10/615 SHREDDER / GRANULATOR COMBO UNIT


    BALL & JEWEL SB10/614-A-11 SHREDDER / GRINDER COMBINATION PACKAGE, SHREDDER S/N 6646-122958, DUAL SHAFTS WITH 1.250 WIDE SINGLE HOOK KNIVES POWERED BY A MARATHON 10 HP 230/460 VOLT 1155 RPM MOTOR THRU A GEARBOX, 24″ WIDE X 22″ CHAMBER AREA, 100″ IN-FEED HEIGHT, GRAVITY DISCHARGES INTO BALL & JEWEL MODEL SG2026-SX GRANULATOR, S/N 6647-122958, 3 KNIFE ROTOR WITH KNIFE CARRIERS, 2 BED KNIFE, POWERED BY A 50 HP 460 VOLT MOTOR, 3/8″ SCREEN INSTALLED, 5″ OD AIRVEYOR DISCHARGE WITH BINDICATOR, SYSTEM MOUNTED ON 65″ WIDE X 38″ DEEP PLATE BASE WITH V-CASTERS AND V-TRACK, INCLUDES STARTER / CONTROL PANEL

  • Array ( [0] => shredders [1] => shredders )
  • Stock#: 16569

    USED BALL & JEWEL SB15 DUAL SHAFT SHREDDER


    BALL AND JEWEL MODEL SB15 DUAL SHAFT SHREDDER, S/N SB15/515-A-11X, 21″ X 20″ CHAMBER WITH 1.250 WIDE 2 HOOK CUTTERS ON ONE SHAFT AND 1.250 WIDE SINGLE HOOK CUTTERS ON 2ND SHAFT, 33″ X 29″ IN-FEED OPENING, MOUNTED ON 33″ TALL GRAVITY DISCHARGE BASE, POWERED BY A BALDOR 15 HP 230/460 VOLT MOTOR, WIRED FOR 460V OPERATION, HAS CONTROLS BUT NO DISCONNECT

  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => shredders [3] => just-arrived [4] => 75-hp-granulators [5] => shredders )
  • Stock#: 17280

    USED SSI M55E SHREDDER / CUMBERLAND 1837B SYSTEM PACKAGE


    SSI model M55E two shaft dual-shear shredder, S/N S2455, manufactured 11/2013, low speed and high torque 20-3/4″ x 40-1/2″ cutting chamber with five 3-3/4″ wide and one 1-3/4″ cutters per shaft powered by a inverter duty 25 hp 230/460 volt 1765 rpm motor thru a 69.7:1 gear reducer, includes original OEM control / starter panel

    Cumberland Model 1837B Granulator, S/N 50510-18004, 18″ x 37″ feed throat, 5 knife high shear hard-faced rotor, hard faced cutting chamber, 2 bed knives, 100 HP 460 volt motor, mounted on 22″ tall plate base, 10″ airveyor discharge, includes soft starter control panel, less than 100 hours use on the granulator and starter.

    Also includes, Sterling 9015FV 15 HP blower with heavy duty housing, heavy duty removable outlet, and steel impeller upgrades, 10″ OD inlet & outlet. Sterling #15 cyclone with dual 10″ OD inlets and heavy duty replaceable inlet/upper cone wear liner. Lot of 10″ (FK250) Kongskilde connecting pipe and late model hydraulic gaylord dumper

    Customer choice to include in-feed and take away conveyors (originally used on different in-feed and discharge configurations for the shredder)

    Take away conveyor is 17′ long with a 22″ wide rubber cleated belt, 3″ tall cleats on 30″ centers, 18″ tall side walls, powered by a 1.5 hp 1730 rpm motor thru a 80:1 gear reducer, 5″ diameter head pulley, in- feed conveyor is 13′ long with a 22″ wide rubber cleated belt, 3″ tall x 8″ wide partial cleats on 11″ centers, 12″ tall side-walls, powered by a 1/2 hp 1750 rpm motor thru 125:1 gear reducer, 8″ diameter head pulley, variable speed 460 volt controls (pictures are available of the original shredder and conveyor configuration)


  • Array ( [0] => shredders [1] => shredders )
  • Stock#: 14846

    VECOPLAN VH22/100CW SHREDDER


    VECOPLAN MODEL VH22/100CW SHREDDER, S/N 12495010, SINGLE SHAFT 30 KNIFE V-BELT DRIVEN ROTOR DRIVEN BY A 100 HP 460 VOLT MOTOR, VIBRATORY IN-FEED CONVEYOR AND FEED ROLLS FOR PROFILES, VIBRATOR CONVEYOR IS 16′ LONG AND HAS A NON-METALLIC SECTION FOR THE S&S GLS700/300175/289 APERTURE STYLE METAL DETECTOR, MFG 2010, INCLUDES OEM STARTER CONTROL PANEL FOR THE SHREDDER AND METAL DETECTOR

  • Array ( [0] => shredders [1] => shredders )
  • Stock#: 10225

    SATRIND K25/100 DUAL SHAFT SHREDDER


    SATRIND MODEL K25/100 DUAL SHAFT SHREDDER, S/N 246901, 17 X 2 KNIVES 3″ THICK EACH, 42″ X 100″ CUTTING AREA, POWERED BY A 100 HP 208-230/460 HYDRAULIC STATION, S/N 246901-CE, RADIATOR/FAN COOLING SYSTEM, STAND ALONE CONTROL PANEL, GRAVITY DISCHARGE, INCLUDES STEEL MESH 8’W X 14’L CONVEYOR AND ERIEZ METAL DETECTOR, 48 X 100 APERTURE, STYLE 9902281, S/N 144359, EZ-5 CONTROLLER, ERIEZ CONVEYOR (PLASTIC BELT) STYLE 9938532, S/N 136615, N-12 CONTROLLER, REVERSING/AUTO/MANUAL

  • Array ( [0] => shredders [1] => shredders )
  • Stock#: 10709

    RETECH VH34/75 HORIZONTAL SHREDDER


    RETECH MODEL VH34/75 HORIZONTAL SHREDDER, S/N 8810010, 5″ X 34″ IN-FEED OPENING, 16″ DIAMETER 44 CUTTER ROTOR, 390 RPM ROTOR SPEED, ROTOR IS BELT DRIVEN BY 75 HP 460 VOLT 1185 RPM MOTOR, TWO INFEED ROLLERS POWERED BY APPROX 1 KW SEW EURODRIVE MOTORS AND GEARBOXES, 41.5″ IN-FEED HEIGHT, INCLUDES STAND ALONE STARTER/CONTROL PANEL AND 34″ WIDE X 30 FOOT LONG VIBRATORY IN-FEED CONVEYOR MODEL VR85/12, S/N 8809020, NO CONTROLS FOR CONVEYOR, ALL 2006 MODEL YEAR

  • Array ( [0] => shredders [1] => shredders )
  • Stock#: 10738

    LINDNER MS2000-S SUPER MICROMAT SINGLE SHAFT VARIABLE SPEED SHR


    LINDNER MODEL MS2000-S SUPER MICROMAT SINGLE SHAFT VARIABLE SPEED SHREDDER, S/N 975 2003, 65″ X 80″ FEED OPENING, 22″ DIAMETER 80″ WIDE WATER COOLED ROTOR WITH 104 CUTTER IN A MONO-FIX SYSTEM, 3 PC COUNTER KNIFE, 3 PC SCRAPER KNIFE, 132 KW MAIN MOTOR (175 HP), 150-345 RPM VARIABLE SPEED ROTOR RANGE, 10.5 KW (14 HP) HYDRAULIC RAM PUMP, 1 HP WATER RE-CIRCULATION COOLER PUMP, 460 VOLT CONTROLS WITH VARIABLE SPEED DRIVE IN STAND ALONE CONTROL CABINET, SIEMENS OP7 TOUCH SCREEN CONTROLS, 2003 MODEL YEAR

  • Array ( [0] => shredders [1] => shredders )
  • Stock#: 12833

    VECOPLAN RG62/150SPKFF SINGLE SHAFT SHREDDER


    VECOPLAN MODEL RG62/150SPKFF SINGLE SHAFT SHREDDER, S/N 7661010, 14.57″ DIAMETER X 62.99″ W CORED FIBER ROTOR WITH 90 BOLT ON INDEX ABLE CUTTERS, OUTBOARD PILLOW BLOCK BEARINGS, 145 RPM ROTOR SPEED, 150 HP 460 VOLT 1784 RPM DRIVE MOTOR THRU FLENDER GEARBOX, 63″ WIDE X 80″ DEEP INFEED OPENING WITH BOLT ON HOPPER, HYDRAULIC FEED RAM, END DISCHARGED THRU 2″ HOLES SCREEN, INCLUDES OEM VECOPLAN TOUCH-SCREEN CONTROL PANEL AND A 55″ WIDE X 234″ LONG RUBBER BELT CONVEYOR POWERED BY A 1.5 HP GEAR MOTOR, UP TO 25,000 LB/HR THROUGHPUT (MATERIAL TYPE/SCREEN SIZE DEPENDENT)