Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17362

    USED NRM 4.5″ 24:1 L/D 150 HP EXTRUDER


    One (1) used NRM 4.5″ 24:1 L/D PM III extruder having a six (6) zone electrically heated, water cooled (closed loop) barrel at a 42″ center-line height. Gearbox has a reduction ratio of 25.14:1 and is rated at 141 HP at a service factor of 1.25. The gearbox is direct driven in a tuck under manner by a 150 HP Reliance D/C motor with Reliance SCR. Gearbox has an oil pump and heat exchanger. The extruder has a water-cooled feed throat with 4.5” on center round  entrance. The temperature control panel has six (6) zones for the barrel and four (4) zones of temperature controls for die zones. Handi-clamp on the discharge. Temperature control 460/3/60 180 FLA. Drive Control 460/3/60. S/N 18080, Shop order 108597. Manufactured 7/1982. Includes gravity feed hopper and spare drive

  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => pelletizing-lines [3] => just-arrived [4] => extruders-twin-screw [5] => pelletizing-lines )
  • Stock#: 17395

    USED LEISTRITZ/GALA 27mm COMPOUNDING LINE


    One (1) used Leistritz/Gala 27mm compounding line consisting of the following:

    One 27mm 40:1 Leistritz model Micro 27 40GL/40D twin screw extruder having co-rotating inter-meshing screws. Barrel is electrically heated, water cooled and consists of nine (9) barrel sections. Gearbox is direct driven by a 10.5 KW (14.3 HP) D/C motor with SCR allowing for an approximate maximum screw speed of 500 RPM. Integral movable control panel has eleven (11) zones of temperature control and all operator controls. Includes pre-polymer metering pump and three (3) sets of screw shafts with loose screw elements. Manufactured in 1997. S/N 2553. Pulled from service in January of  2021. Gala model 6PDV polymer diverter valve with 10 HP hydraulic pump. Unit is used until the extruder is up to speed. Gala model SLC6 underwater pelletizer with 4.3 KW (5.3 HP) spring loaded cutter, model 40TWS water tempering system with heated reservoir, 3 HP water pump, heat exchanger, Gala model 8.1BF spin dryer with agglomerate catcher and free-standing control panel with touch screen controls. Offered less die. Includes spare blades, heater bands, and manuals. 460V/3ph/60Hz 46 FLA. Manufactured in 2000. S/N 10100743.

  • Array ( [0] => just-arrived [1] => mixers [2] => just-arrived [3] => mixers )
  • Stock#: 17422

    USED JAEGER RE-900 ROTARY BATCH MIXER


    Jaeger model RE-900 steel rotating batch blender, 403 cubic foot working capacity, carbon steel construction. Direct driven by a 40 HP motor through a gear reducer. Previously used for batch blending Approx. 10,000 pounds of plastic with additives (2 available)

  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17407

    USED LEISTRITZ 50mm TWIN SCREW EXTRUDER


    Leistritriz 50mm twin screw compounding extruder with a 40:1 L/D ratio. Screws are co-rotating and inter-meshing at a 42″ center-line height. Feed entrance is 3″ x 3″. Barrel is electrically heated and water cooled and consists of ten (10) barrel sections including feed, top vent, side feed, and seven (7) closed sections. Screws and barrel sections were replaced in 2016. Eisenbeiss gearbox was replaced in 2015 and is direct driven by a 54 KW (72 HP) A/C motor with Emerson Quantum III control. Gearbox is rated at 2 x 600 newton meters. Free standing control panel with eleven (11) zones of temperature controls that also houses the drive control and operator controls. Package includes Leistritz side feeder with twin screws and 1.5 kw drive and 2.2 kw water centrifugal vacuum pump with micron technology filter. Pulled from service in March of 2021. Last used for compounding LDPE. 460V/3ph/60Hz. 250 amp main disconnect.

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-spin-dryers [3] => just-arrived [4] => pelletizers [5] => pelletizing-spin-dryers )
  • Stock#: 17408

    USED GALA MAP-6 PELLETIZING SYSTEM


    Gala model MAP-6 pelletizing system including cutter with 4 KW motor, die, and water box mounted on a stand, 40 GPM tempered water system with pump, reservoir, heater, heat exchanger and model 2008-BF spin dryer. Free standing OEM control panel. 460/3/60 input power. 64 full load amps. S/N 10200656. Manufactured in 2001. Last used with a 6″ 30:1 300 HP Davis Standard extruder

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17406

    USED DAVIS STANDARD 6″ 30:1 L/D EXTRUDER


    Davis Standard model 600STVW 6″ 30:1 L/D extruder, S/N 7-69006. Extruder has a five (5) zone electrically heated, water cooled non vented barrel at a 42″ center-line height. Gearbox has a reduction ratio of 17.38:1 and is rated at 300 HP at a service factor of 1.5. Gearbox was rebuilt by AES in august of 2014. Shaft mounted oil pump and filter. Gearbox is belt driven by a 300 HP 1150/2000 RPM field weakened D/C motor with SCR control. Water cooled feed throat has Conair mixer and bunting magnet mounted on the entrance. Temperature control panel has seven (7) zones of controllers. Cored extrusion screw with rotary union. C-clamp on the barrel discharge. Pulled from service 3/2021 as product line was discontinued

  • Array ( [0] => just-arrived [1] => injection-molding [2] => just-arrived [3] => injection-molding )
  • Stock#: 17397

    USED FERROMATIK MILACRON VISTA V55 MOLDING MACHINE


    Ferromatik Milacron model Vista V55 injection molding machine. Unit has a clamping force of 55 tons and a 1.76 oz shot capacity. Toggle clamp. 12.8″ x 12.2″ tie bar spacing. Platens measure 20.08″ x 19.67″. Clean machine with 6170 original hours. Siemens Xtreem NT controller upgraded to Xtreem ST in 2017. S/N S55A0500076. Manufactured in 2002. College lab use. Manual included. 460/3/60 input. 6500 lbs. 11′ x 4′ x 6′

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 17437

    USED DAVIS STANDARD 1/4″ TUBING EXTRUSION LINE


    Davis Standard 1/4″ tubing extrusion line including the following equipment:

    A. Davis Standard / Killion model KN-100 1.00″ 24:1 L/D extruder having a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 39″ centerline height. Gearbox is belt driven by a 3 HP D/C motor with SCR control. Unitized temperature control panel has six (6) zones of Eurotherm controllers consisting of three (3) zones for the barrel and three (3) zones for the c-clamp and die. C-clamp is mounted on the discharge. Includes gravity feed hopper. BOM number 05180. 230V/1ph/50-60Hz input, 47 FLA.

    B. Nominal ¼” diameter electrically heated tubing die.

    C. Davis Standard / Killion medical tubing vacuum tank measuring 116″ long with an 8″ x 8″ cross section. Stainless steel construction. Two glass doors. Upstream and downstream adjustment as well as up and down adjustment. Includes vacuum pump with 3 HP D/C motor, water pumps, sizing fixture, and controls. S/N 30176. 230V/1ph/60Hz input.

    D. Davis Standard / Killion belt puller having a 2″ wide belt with 22″ of contact length. Powered by an approximate 1.5 HP D/C motor. Manually actuated top belt. S/N 30174. 230V/3ph/60Hz input, 10 FLA.

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17345

    LOW HOURS LINDNER L1100 SHREDDER SYSTEM


    Little used Lindner shredding system (2011) with approximately 50 hours of use. System includes the following:

    A. Hydraulic bin tipping unit with safety cage.

    B. 700mm (27.5″) wide in feed conveyor with 2,000mm (6’5″) long straight section and 4,500mm (14’6″) incline section at 30 degrees. 1,500mm (4’8″) long horizontal discharge section. Conveyor is chain driven with PVC belt and 76mm (3″) chain pitch. Variable speed with controls.

    C. Model Vega L1100 single shaft shredder having an 1,100mm (43.3″) wide entrance with a 48 knife rotor. 1,080mm x 1,124mm throat opening (42″ x 44″). Voltage is 400/3/50 – 460/3/60 input. Rotor is belt driven by a 55 KW (71.5 HP) drive at 50 Hz or 63 KW (81.9 HP) drive at 60 Hz. Last used on 400/3/50. 50mm screen installed. PLC controlled. S/N 1630

    D. 700mm (27.5″) wide discharge conveyor with 2,000mm long straight section and 8,000mm long inclined section. Variable speed with controls.

    Located in the United Kingdom

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17333

    USED CALIFORNIA PELLET MILL CONDITIONER


    One (1) California Pellet Mill conditioner for use with a pellet mill. Mixing section measures approximately 28″ in diameter x 8′ long. Unit is belt driven by approximately a 15 HP motor through a gear reducer

  • Array ( [0] => just-arrived [1] => miscellaneous [2] => just-arrived [3] => miscellaneous )
  • Stock#: 17329

    USED CHAMPION 20″ X 44″ HAMMER-MILL


    One (1) used Champion model 20″ x 44″ Magnum hammer-mill. Unit has 2,400 cubic inches of screen area with a 3/16″ screen installed. 200 HP 1800 RPM motor supplies a 20,730 RPM tip speed. 44″ diameter rotor. Serial number 102396. 460/3/60, 230 amps.

  • Array ( [0] => just-arrived [1] => as-is-granulators-30-hp [2] => just-arrived [3] => as-is-granulators-30-hp )
  • Stock#: 17337

    USED CMG / CUMBERLAND 1842i GRANULATOR SYSTEM


    Cumberland / Gloucester model 1842i granulator. 18″ x 42″ feed throat with three (3) knife open rotor. Rotor is belt driven by a 100HP 1,775 RPM 460V 134 FLA motor. Two (2) bed knives. Insulated tray feed hopper with 19.5″ x 42″ opening. Insulated body panels. Set up for 6″ OD airveyor discharge. Discharge is via a Sterling model 6005FV blower with a 7.5 HP motor. Includes a free standing console type control panel with Alan Bradley Dialog Plus soft starter. Granulator S/N 01703024.

    Price: $42,500.00, as is.