Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => extrusion-roll-stacks-rolls [3] => extrusion-sheet-lines [4] => just-arrived [5] => extruders-3-5-10 [6] => extrusion-roll-stacks-rolls [7] => extrusion-sheet-lines )
  • Stock#: 16932

    USED PTI 78″ SHEET LINE


    USED PTI 78″ WIDE SHEET LINE (2003) LAST USED ON PET SHEET

    A – PTI MODEL 6000 6″ 36:1 L/D EXTRUDER HAVING AN EIGHT (8) ZONE ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP) AND VENTED BARREL AT A 64″ CENTER-LINE HEIGHT. GEARBOX IS A FLENDER MODEL SZNF 390, HAS A 15.4:1 REDUCTION RATIO RATED FOR UP TO 986 HP. GEARBOX IS DIRECTLY DRIVEN BY A 500 HP DC MOTOR. OFFERED LESS SCR CONTROL. SCREW IS DESIGNED FOR USE ON PET AND HAS PROVISION FOR COOLING. CONTROL PANEL HAS 25 ZONES OF EUROTHERM CONTROLLERS. SERIAL NUMBER 3767/10082. MANUFACTURED 6/2003

    B – DYNISCO MODEL EH-60 SCREEN CHANGER HAVING TWO NOMINAL 6″ DIAMETER BREAKER PLATES. INCLUDES 2 HP HYDRAULIC POWER PACK.

    C – MAAG MODEL 90/90 MELT PUMP WITH 30 HP DRIVE SYSTEM, CONTROLS, AND MODEL 6000 STATIC MIXER.

    D – CLOEREN 70″ AUTO-FLEX SHEET DIE. 1″ X 4″ BACK CENTER FEED ENTRANCE. SERIAL NUMBER 77831-2129. MANUFACTURED 4/2003.

    E – PTI MODEL 7824 DOWN STACK ROLL STAND HAVING THREE ROLLS MOUNTED IN A VERTICAL ARRANGEMENT CONSISTING OF 24″ DIAMETER MIDDLE AND BOTTOM CHROME PLATED ROLLS AND AN A 16″ DIAMETER CHROME PLATED TOP ROLL. HYDRAULICALLY ACTUATED GAPPING. ROLLS ARE DRIVEN BY A 10 HP AC MOTOR THROUGH GEARBOXES VIA SILENT CHAIN AND SPROCKETS. INCLUDES BUILT ONTO FRAME TEMPERATURE CONTROL SYSTEM (MISSING ONE PUMP), IDLER CONVEYOR, DIP COATING STATION, SLITTING STATION, AND PULL ROLL STAND WITH 78″ X 8″ DIAMETER ROLLS. SERIAL NUMBER 3354R. 480/3/60. 175 AMPS.

    F – 78″ PARKINSON TURRET WINDER HAVING FOUR WINDING POSITIONS. EACH STATION IS DRIVEN BY A 5 HP AC MOTOR. INCLUDES THREE WINDING SHAFTS. MISSING GEARBOX ON TURRET.

    G – PREVIOUSLY RUNNING PET. LINE WAS ORIGINALLY FACTORY DESIGNED TO RUN PET, PP, AND PS AT 2500-3000 POUNDS AN HOUR.

    PICTURES AVAILABLE ON REQUEST

  • Array ( [0] => just-arrived [1] => balers [2] => just-arrived [3] => balers )
  • Stock#: 16942

    USED BALEMASTER 360-A HORIZONTAL BALER


    BALEMASTER MODEL 360-A HORIZONTAL CLOSED END BALER, S/N B0221-04-801001, 60″ X 30″ X 42″ BALE SIZE, POWERED BY A 20 HP 3 PHASE MOTOR, 41 FULL AMP LOAD, 6″ HYDRAULIC EJECTION DOOR CYLINDER, 48″ X 35″ HOPPER OPENING, OVERALL DIMENSIONS ARE 190″ X 48″ X 82.25″, APPROXIMATELY 10,000 LBS EMPTY

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 16938

    USED VECOPLAN RG42/30SWU SHREDDER


    VECOPLAN MODEL RG42/30SWU SHREDDER, S/N 10242010, 42″ X 48″ CHAMBER, 27 CUTTER ROTOR, 30 HP 460 VOLT MOTOR, 8″ RIGHT HAND AIRVEYOR DISCHARGE, 2″ HOLES SCREEN, MEASURES 87″ X 72″ X 76″, 82″ HOPPER OPENING, 2 HP RAM, 2007 MODEL YEAR, INCLUDES OEM CONTROL PANEL

  • Array ( [0] => just-arrived [1] => 35-60-hp-granulators [2] => feed-paddle-roll-granulators [3] => just-arrived [4] => 35-60-hp-granulators [5] => feed-paddle-roll-granulators )
  • Stock#: 16922

    USED CUMBERLAND 1456 FEED ROLL GRANULATOR


    CUMBERLAND MODEL 1456 GRANULATOR, S/N 84000-87011, 14″ X 56″ FEED THROAT, 3 KNIFE OPEN ROTOR, 2 BED KNIFE, 50 HP 230/460 VOLT 1175 RPM MOTOR, CONVEYOR FEED HOPPER WITH REAR MOUNTED 5″ DIAMETER X 56″ WIDE STEEL KNURLED FEED ROLLS, FEED ROLLS HAVE PNEUMATIC PINCH AND ARE POWERED BY A 1.5 HP 208-230/460 VOLT 1140 RPM MOTOR THRU A 40:1 GEARBOX AND CHAIN & SPROCKET DRIVE SYSTEM, GEARBOX IS RATED FOR A MAXIMUM OF 1.85 HP AND HAS AN OUTPUT TORQUE OF 2080 LBS PER INCH, CHAMBER IS MOUNTED TO A LOW PROFILE PLATE BASE ON VIBRATION CONTROL PADS, 10″ OD AIRVEYOR DISCHARGE, INCLUDES PNEUMATIC AIR VALVE CONTROL SYSTEM FOR THE FEED ROLLS, OVERALL DIMENSIONS ARE 10′ X 80″ X 100″, APPROXIMATELY 10,000 LBS, STARTER AND CONTROLS FOR THE GRANULATOR ARE NOT INCLUDED

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16914

    USED MERRITT / DAVIS 3.5″ 24:1 L/D EXTRUDER


    USED 3.5” 24:1 L/D MERRITT-DAVIS STANDARD EXTRUDER HAVING A FIVE (5) ZONE ELECTRICALLY HEATED, AIR COOLED BARREL AND NON VENTED BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A REDUCTION RATIO OF 26.25:1 AND IS SET UP FOR A BELT DRIVE MOTOR. ON CENTER WATER COOLED FEED THROAT. UNITIZED TEMPERATURE CONTROL PANEL FOR SEVEN (7) CONTROLLERS (ONE MISSING).  C CLAMP ON DISCHARGE. UNIT PRESENTLY OFFERED WITHOUT, SCREW, MOTOR, AND SCR DRIVE, MANUFACTURED IN 2001. S/N PR-03729-01

    OR

    MERRITT-DAVIS STANDARD 3.5” 24:1 L/D EXTRUDER HAVING A FIVE (5) ZONE ELECTRICALLY HEATED AIR-COOLED BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A REDUCTION RATIO OF 26.25:1 FOR A SCREW SPEED OF 67 RPM. 100 HP BELT DRIVE MOTOR . ON CENTER WATER COOLED FEED THROAT. UNITIZED TEMPERATURE CONTROL PANEL FOR SEVEN (7) CONTROLLERS.  C CLAMP ON DISCHARGE. INCLUDES SCREW AND SCR MOTOR DRIVE, MANUFACTURED IN 2001. S/N PR-03729-01, UNIT GONE THROUGH AND IN RUNNING ORDER


  • Array ( [0] => just-arrived [1] => pulverizers [2] => just-arrived [3] => pulverizers )
  • Stock#: 16912

    USED PALLMANN PB8 PULVERIZER


    PALLMANN MODEL PP8 PULVERIZING SYSTEM.  ROTORS ON PULVERIZER MEASURE 31.2″ (800 MM) IN DIAMETER WITH DOUBLE CONE IMPELLER FOR PULVERIZING OF PLASTICS. INCLUDES (2) DRIVE MOTORS 35 HP AND 75 HP.  CARBON STEEL, WATER COOLED CHAMBER. PACKAGE INCLUDES ERIEZ MODEL D STYLE 26 FEEDER, 20 HP BLOWER WITH 7” INLET AND 10” OUTLET, 33.5” LONG CYCLONE WITH 6” BOLT ENTRANCE AND ROTARY VALVE ON DISCHARGE, 98” LONG CYCLONE WITH 10” INLET, 30” SWECO SCREENER AND CONTROL PANEL

  • Array ( [0] => just-arrived [1] => 35-60-hp-granulators [2] => feed-paddle-roll-granulators [3] => just-arrived [4] => 35-60-hp-granulators [5] => feed-paddle-roll-granulators )
  • Stock#: 16836

    USED RAPID 500/120 FEED ROLL GRANULATOR


    RAPID MODEL 500-120 KURF GRANULATOR WITH FEED ROLLS, S/N RA 511.246815.20.1, 18″ X 48″ FEED THROAT, 5 KNIFE OPEN ROTOR, 3 BED KNIFE, TANGENTIAL CUTTING CHAMBER, 50 HP 460 VOLT MOTOR, 6″ LEFT HAND AIRVEYOR DISCHARGE, 8mm HOLES SCREENS INSTALLED, INSULATED HOPPER WITH REAR MOUNTED 1200mm WIDE KNURLED STEEL FEED ROLLS WITH DANCER BAR, FEED ROLLS HAVE PNEUMATIC PINCH, HOPPER HAS ELECTRIC POWER BACK JACK ASSIST, INCLUDES ORIGINAL OEM STARTER PANEL WITH ALLEN BRADLEY SOFT STARTER FOR THE GRANULATOR AND A VARIABLE SPEED DRIVE (8-45 METERS/MIN LINE SPEED) (26 – 147 FEET/MIN LINE SPEED) FOR THE FEED ROLLS, REMOTE KEYPAD CONTROL FOR THE FEED ROLLS MOUNTED ON STARTER DOOR, 2015 MODEL YEAR WITH LOW USE AND IS IN EXCELLENT RUNNING CONDITION

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16839

    USED AET 6″ 24:’ L/D 300 HP EXTRUDER


    AET MODEL 60ASLT24 6″ 24:1 L/D EXTRUDER HAVING A SEVEN (7) ZONE ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP) BARREL AT A 45″ CENTER-LINE HEIGHT. GEARBOX IS A KOELLMANN MODEL UNEX 8.12 , HAS A REDUCTION RATIO OF 20.07:1 AND IS RATED AT 400 HP AT A SERVICE FACTOR OF 1.6. GEARBOX IS DIRECT DRIVEN OUT THE BACK BY A 300 HP 1755 RPM ABB AC MOTOR WITH INVERTER. WATER COOLED FEED THROAT WITH 7″ WIDE X 10″ LONG ON CENTER ENTRANCE. TEMPERATURE CONTROL PANEL WITH FOURTEEN ZONES. S/N E2355. MANUFACTURED 1/28/04. 460/3/60 INPUT

  • Array ( [0] => just-arrived [1] => high-intensity-mixers [2] => mixers [3] => ribbon-blenders [4] => just-arrived [5] => high-intensity-mixers [6] => mixers [7] => ribbon-blenders )
  • Stock#: 16833

    USED CHARLES ROSS & SON COMPANY JACKETED RIBBON MIXER/DRYER


    CHARLES ROSS & SON COMPANY JACKETED RIBBON MIXER/DRYER, MODEL 42C-18, S/N 111144, APPROXIMATELY 600 LITER (25 CUBIC FOOT) CAPACITY, APPROXIMATE 30″ DIAMETER X 60″ LONG INTERIOR DIMENSION, JACKET CERTIFIED BY ROSS METAL FABRICATORS, NATIONAL BOARD #699, S/N 6830, INTERNAL PRESSURE 150 PSI @ 365°F, JACKET PRESSURE 50 PSI @ 365°F, DRIVEN BY A 15 HP MOTOR THROUGH A GEARBOX

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 16841

    USED DAVIS STANDARD 6″ 30:1 L/D 300 HP EXTRUDER


    DAVIS STANDARD MODEL 60IN60T 6″ 30:1 L/D EXTRUDER HAVING A SEVEN (7) ZONE ELECTRICALLY HEATED, WATER COOLED (CLOSED LOOP) BARREL AT A 42″ CENTER-LINE HEIGHT. GEARBOX HAS A REDUCTION RATIO OF 24.29:1 AND IS RATED AT 530 HP AT A SERVICE FACTOR OF 1.5. GEARBOX IS DIRECT DRIVEN IN A WRAP AROUND MANNER BY A 300 HP 1750/2500 RPM RELIANCE AC MOTOR WITH INVERTER. GEARBOX HAS PUMP, FILTER, AND LARGE HEAT EX-CHANGER FOR COOLING. 7″ X 11″ WATER COOLED FEED THROAT. TEMPERATURE CONTROL PANEL WITH APPROXIMATELY FOURTEEN (14) ZONES OF NEW TEMPERATURE CONTROLLERS. CONTROL PANEL AND INVERTER ARE UNITIZED ON THE SAME BASE AS THE EXTRUDER. EXTREMELY CLEAN. APPROXIMATELY 2000 HOURS OF USE. S/N AU143. S/O 78356. MANUFACTURED 8/04

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 16870

    USED SSI M55E DUAL SHAFT SHREDDER


    SSI MODEL M55E TWO SHAFT DUAL-SHEAR SHREDDER, S/N S2455, MANUFACTURED 11/2013, LOW SPEED AND HIGH TORQUE 20-3/4″ X 40-1/2″ CUTTING CHAMBER WITH FIVE 3-3/4″ WIDE AND ONE 1-3/4″ CUTTERS PER SHAFT (CUTTERS ARE IN GOOD CONDITION). POWERED BY A INVERTER DUTY 25 HP 230/460 VOLT 1765 RPM MOTOR THRU A 69.7:1 GEAR REDUCER, MOUNTED ON A 68″ X 68″ STAND, STAINLESS STEEL BOLT ON TOP FEED HOPPER, GRAVITY DISCHARGE THRU A TRANSITION FOR INCLUDED TAKE AWAY CONVEYOR, TAKE AWAY CONVEYOR IS 17′ LONG WITH A 22″ WIDE RUBBER CLEATED BELT, 3″ TALL CLEATS ON 30″ CENTERS, 18″ TALL SIDE-WALLS, POWERED BY A 1.5 HP 1730 RPM MOTOR THRU A 80:1 GEAR REDUCER, 5″ DIAMETER HEAD PULLEY, IN- FEED CONVEYOR IS 13′ LONG WITH A 22″ WIDE RUBBER CLEATED BELT, 3″ TALL X 8″ WIDE PARTIAL CLEATS ON 11″ CENTERS, 12″ TALL SIDE-WALLS, POWERED BY A 1/2 HP 1750 RPM MOTOR THRU 125:1 GEAR REDUCER, 8″ DIAMETER HEAD PULLEY, VARIABLE SPEED 460 VOLT CONTROLS, ALSO INCLUDES ORIGINAL OEM 460 VOLT SHREDDER CONTROL PANEL WITH ALLEN BRADLEY PLC

  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => pelletizers [3] => pelletizing-lines [4] => just-arrived [5] => extruders-twin-screw [6] => pelletizers [7] => pelletizing-lines )
  • Stock#: 16811

    USED 27mm LEISTRITZ / CONAIR PELLETIZING LINE


    LEISTRITZ / CONAIR PELLETIZING LINE CONSISTING OF ONE 27mm LEISTRITZ MODEL 27GL-40D CO-ROTATING TWIN EXTRUDER WITH SIDE FEEDER, OPERATOR / TEMPERATURE CONTROL PANEL, INCLUDES STRAND DIE, CONAIR MODE 304 PELLETIZER, SPARE SCREW SHAFT & ELEMENTS, REPORTED TO HAVE 728 HOUR USE