One (1) used NRM 4.5″ 24:1 L/D PM III extruder having a six (6) zone electrically heated, water cooled (closed loop) barrel at a 42″ center-line height. Gearbox has a reduction ratio of 25.14:1 and is rated at 141 HP at a service factor of 1.25. The gearbox is direct driven in a tuck under manner by a 150 HP Reliance D/C motor with Reliance SCR. Gearbox has an oil pump and heat exchanger. The extruder has a water-cooled feed throat with 4.5” on center round entrance. The temperature control panel has six (6) zones for the barrel and four (4) zones of temperature controls for die zones. Handi-clamp on the discharge. Temperature control 460/3/60 180 FLA. Drive Control 460/3/60. S/N 18080, Shop order 108597. Manufactured 7/1982. Includes gravity feed hopper and spare drive
Leistritz / Gala 27mm compounding line consisting of the following components:
One 27mm 40:1 Leistritz model Micro 27 40GL/40D twin screw extruder with co-rotating inter-meshing screws. Barrel is electrically heated, water cooled and consists of nine (9) barrel sections. Gearbox is direct driven by a 10.5 KW (14.3 HP) DC motor with SCR (silicone controlled rectifier) allowing for an approximate maximum screw speed of 500 RPM. Integral movable control panel has eleven (11) zones of temperature control and all operator controls. Includes pre-polymer metering pump and three (3) sets of screw shafts with loose screw elements. Manufactured in 1997. S/N 2553. Pulled from service in January of 2021. Gala model 6PDV polymer diverter valve with 10 HP hydraulic pump. Unit is used until the extruder is up to speed. Gala model SLC6 underwater pelletizer with 4.3 KW (5.3 HP) spring loaded cutter, model 40TWS water tempering system with heated reservoir, 3 HP water pump, heat exchanger, Gala model 8.1BF spin dryer with agglomerate catcher and free-standing control panel with touch screen controls. Offered less die. Includes spare blades, heater bands, and manuals. 460V/3ph/60Hz 46 FLA operation . Manufactured in 2000. S/N 10100743.
Jaeger model RE-900 steel rotating batch blender, 403 cubic foot working capacity, carbon steel construction. Direct driven by a 40 HP motor through a gear reducer. Previously used for batch blending approximately10,000 pounds of plastic with additives.
Davis Standard 1/4″ tubing extrusion line including the following equipment:
A. Davis Standard / Killion model KN-100 1.00″ 24:1 L/D extruder having a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 39″ centerline height. Gearbox is belt driven by a 3 HP D/C motor with SCR control. Unitized temperature control panel has six (6) zones of Eurotherm controllers consisting of three (3) zones for the barrel and three (3) zones for the c-clamp and die. C-clamp is mounted on the discharge. Includes gravity feed hopper. BOM number 05180. 230V/1ph/50-60Hz input, 47 FLA.
B. Nominal ¼” diameter electrically heated tubing die.
C. Davis Standard / Killion medical tubing vacuum tank measuring 116″ long with an 8″ x 8″ cross section. Stainless steel construction. Two glass doors. Upstream and downstream adjustment as well as up and down adjustment. Includes vacuum pump with 3 HP D/C motor, water pumps, sizing fixture, and controls. S/N 30176. 230V/1ph/60Hz input.
D. Davis Standard / Killion belt puller having a 2″ wide belt with 22″ of contact length. Powered by an approximate 1.5 HP D/C motor. Manually actuated top belt. S/N 30174. 230V/3ph/60Hz input, 10 FLA.
One (1) used 1.5″ 20:1 L/D ratio Davis Standard rubber extruder with powered feed roll on throat. Barrel is electrically heated, water cooled (closed loop) and vented at approximately a 42″ centerline height. Includes oil style vacuum pump. C-clamp with die on barrel discharge. Oversize gearbox has a reduction ratio of 17.56:1 and is rated at 50 HP at a service factor of 1.25:1. Gearbox is belt driven by a Marathon Blue Max 25 HP A/C motor with Allen Bradley Power Flex 753 inverter with isolation transformer. Unitized temperature control panel has seven (7) zones of temperature controls. Manufactured January of 2001. Model 150IN20. Shop order number 71118. S/N 16633. 460/3/60 input. 77 FLA.
Rapid model 2442M granulator, no S/N. 24″ x 42″ feed throat, 5 knife rotor with knife carriers, 3 bed knife, 100 HP 230/460V 1765 RPM motor. Dual flywheel, pneumatic assisted side feed hopper and screen cradle, 8″ airveyor discharge. Mounted on 26″ tall leg base, starter and controls are not included.
Cumberland model 2050B granulator, S/N 51310-93014, 20″ x 50″ feed throat, 5 knife steep angle rotor, 2 bed knife, 100 HP 460-volt 1185 RPM motor, OEM style conveyor feed hopper, 10″ airveyor discharge, mounted to a step base, starter and controls not included
Used 16″ Davis Standard Pilot / Laboratory size horizontal sheet/cast line consisting of the following:
(2) 1″ Killion / Davis Standard pedestal style co-extruders each 30:1 L/D driven by 3 HP A/C motors with individual temperature control panels, general purpose 3:1 barrier type screw, air cooled barrels and melt pumps. Includes one (1) spare screw.
(1) 1.25″ Killion / Davis Standard primary 30:1 L/D extruder driven by a 15 HP A/C motor, general purpose 3:1 barrier type screw, individual temperature control panel, gear pump, and air-cooled barrel. Includes four (4) spare screws.
(1) Cloeren Co Ex Block with multiple inserts for co-extrusion. Inserts include AAAAA, BBAAA, CBAAA, AABAA, CAAAB, CCCCC, CBABC, BAAAB, and ABCAA configurations. Manufactured in 2006.
(1) 14″ Cloeren sheet die having a center back entrance but mounted for use in a downward direction. S/N A06-1782-02. Manufactured in 2006
(1) Davis Standard horizontal sheet chill roll stack with three (3) 16″ wide x 24″ OD rolls. With individual motor drive through a gearbox for each roll and built onto frame hydraulic roll loading. Rotary unions for roll cooling/heating with Conair model TC1 stand-alone temperature control. Unit can be run as a cast unit or sheet take-off. With pull rolls.
Also Includes two (2) matt finished rolls, one (1) silicon covered roll and four (4) chrome rolls. Still installed as operated until June 25 2021. New approximately 1995-2006 with laboratory use only.
2020 model year AEC Cumberland model FX1628 granulator, S/N FX1628-20015, 16″ x 28″ feed throat, 3 knife open rotor, 2 bed knife, offset cutting chamber, dual fly wheels, 40 HP 460-volt motor, Insulated conveyor feed hopper and body panels, 6″ left hand airveyor discharge, complete with starter and controls for the granulator and a 5 HP blower, control panel includes amp meter.
One (1) used Parkinson 50 series single turret winder able to handle a maximum package of 60″ wide x 42″ diameter on 6″ Tidland air shafts. Each winding shaft is driven by a 7.5 HP A/C motor. Touch screen controls. Includes power indexing, lay-on roll, bow rolls, shaft extraction and doffing cart. Recently pulled from service. Serial number 6-03-4068-01
One (1) used Gala model 5 underwater pelletizing system, includes 2 HP cutter, two (2) 12-hole dies, one (1) die with nano holes, 20 GPM water system with heater, pump, heater exchanger, 3 HP model 8.1 BF dryer, and free-standing control panel. Also includes four (4) spare cutter assemblies. S/N 85022. very clean.
Cumberland model 1837B granulator, S/N 50510-88009, 18″ x 37″ feed throat, 5 knife high shear rotor, 2 bed knife, 100 HP 460-volt motor, conveyor feed hopper, 8″ right hand airveyor discharge, mounted on 22″ tall plate base, starter and controls not included