Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17730

    USED HPM 3.5″ 24:1 L/D 75 HP EXTRUDER


    HPM model 3.5 TMC-24 3.5″ 24:1 L/D extruder having a four (4) zone electrically heated, air cooled , and non- vented barrel. Gearbox has a reduction ratio of approximately 13.88:1 and is belt driven by a 75 HP brush-less D/C motor with controls. Unitized temperature control panel with seven zones of temperature control. S/N 93182. 460/3/60 input power. Pulled from service 10/2021. Last use on cellulose acetate profiles

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17735

    USED DAVIS STANDARD 3.5″ 34:1 L/D EXTRUDER


    One (1) Used Davis Standard model 35IN35SR 3.5″ extruder, S/N K2191. 34:1 L/D barrel having a seven zone electrically heated and water cooled (closed loop) barrel at a 56″ centerline height. Gearbox has a 5.67:1 reduction ratio and is rated at 158 HP with a service factor of 1.25. Gearbox is belt driven by a 150 HP D/C motor with Control Techniques SCR. Motor was rebuilt in December of 2018. Water cooled feed throat with 4.5″ x 7″ entrance. Integral temperature control panel has thirteen (13) zones of controls. Two instruments are missing. Manufactured 1987. 460-Volt 3-phase 60Hz input power. SO# 99878.

    $0.00
  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 17657

    USED MITTS & MERRILL MS5025 DUAL SHAFT SHREDDER


    Mitts & Merrill model MS5028 dual shaft shredder. Hydraulic ram assisted. Driven by a 150 HP 460-volt motor via belt drive and thru a gearbox. Gravity discharge. Knives are approximately 1.5″ wide each. Includes control panel and a 48″ wide x 30′ long in-feed conveyor.

    $0.00
  • Array ( [0] => just-arrived [1] => pipe-profile-vac-tanks [2] => just-arrived [3] => pipe-profile-vac-tanks )
  • Stock#: 17740

    USED CONAIR 22 FOOT VACUUM SIZING TANK


    One (1) used Conair model MT104-22-5 vacuum sizing tank. Good for up to 2″ diameter tubing or profile. Stainless steel construction. Five( 5) compartments. 22′ tank length, overall length 285″. 1.75 HP vacuum pump and 2 HP water pump. Clear lids. Internal guide rollers. Set up for right to left operation. Revision 064257L060/1103. 230/3/60 input power. S/N 154786. With Huestis air stripper

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17741

    PTI 4000 4″ 30:1 L/D EXTRUDER


    One (1) used 4″ 30:1 L/D ratio PTI model 4000 extruder having a five (5) zone electrically heated, water cooled (closed loop), vented, and plugged barrel at a 53″ center-line height. Flender model E2HA7 gearbox has a reduction ratio of 11.807:1 and is rated at 150 HP. The gearbox is direct driven out the back end by a 150 HP ABB motor with ABB inverter. Gearbox has an oil pump and heat exchanger. The extruder has a water-cooled feed throat with 4″ x 6″ on center entrance. The temperature control panel has five (5) zones for the barrel and fifteen( 15) zones of temperature controls for die zones. Inverter, temperature panel and 5 HP hydraulic power pack for the screen changer are mounted on the sane base as the extruder. Includes Xaloy model EH-45 hydraulic slide plate screen changer, S/N 740. Extruder S/N 4390/1069. Manufactured 2/2007. 460/3/60 input power



    $0.00
  • Array ( [0] => just-arrived [1] => pipe-profile-vac-tanks [2] => just-arrived [3] => pipe-profile-vac-tanks )
  • Stock#: 17742

    USED CONAIR 22 FT VACUUM SIZING TANK


    One (1) used Conair model MT104-22-5 vacuum sizing tank. Good for up to 2″ diameter tubing or profile. Stainless steel construction. Five (5) compartments. 22′ tank length, overall length 285″. 1.75 HP vacuum pump and 2 HP water pump. Clear lids. Internal guide rollers. Set up for right to left operation. With Zumbach thickness gauge with controls and Huestis air stripper. Revision 023699L/010/0304. 230/3/60 input power. Serial number 159983

    $0.00
  • Array ( [0] => just-arrived [1] => pipe-profile-vac-tanks [2] => just-arrived [3] => pipe-profile-vac-tanks )
  • Stock#: 17743

    USED CONAIR 16 FT DUAL VACUUM SIZING TANK


    One (1) used Conair model VC4N22D 16′ dual vacuum sizing tank. Each tank having a 7″ wide x 12″ high cross section. Clear lids are on a 45 degree angle. Stainless steel construction. Five (5) compartments. One tank is set up for right to left operation while the second tank is set up for left to right operation. With Huestis air stripper mounted on the discharge of each tank. With digital controls. Caster mounted. 460/3/60 input power. Job number 25992-20. Manufactured 2012

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17744

    USED DAVIS STANDARD 3.5″ EXTRUDER W/DUAL 1.25″ CO-EXTRUDERS


    Davis Standard straw/tubing co-extrusion extrusion package manufactured 10/2012

    Last used on three color straws extruding two lanes of straws at one time. Extruders and controls are unitized on a single base. 460/3/60 input power. 278 maximum amp load

    A – Davis standard model MV35IN35 3.5” 24:1 L/D extruder having a four (4) zone electrically heated, air cooled, and non-vented barrel at a 42” centerline height. Gearbox has a 17.39:1 reduction ratio and is rated at 257 HP at a service factor of 1.25. Gearbox is belt driven by a 100 HP heavy duty A/C motor with inverter. Extruder presently set up for a maximum screw speed of 100 RPM. integral temperature control panel has ten (10) zones of Davis Standard controllers consisting of four (4) barrel, one (1) screen changer and four (4) die zones. Water cooled feed throat with a 4” x 6” entrance. Barrel is missing one heater band

    B – Mounted on the extruder discharge is an Xaloy model EHC-35 screen changer having two nominal 3.5” diameter breaker plates. S/N EH35-1056

    C – Two (2) incomplete Xaloy melt pumps with 7.5 HP A/C motors and inverters. Missing one (1) motor and one (1) gearbox. Includes free standing control panel

    D – Two (2) used Davis Standard model HPE-125A 1.25” pedestal extruders having electrically heated, air-cooled barrels. Units are height and angle adjustable. Gearbox is a SEW Eurodrive having a 15.19:1 reduction ratio. Each gearbox is direct driven by a Marathon Blue Max 2 HP heavy duty motor. Each extruder has a gravity feed hopper with Conair hopper loader

    E – Two electrically heated straw dies with two co-ex ports on each


    $0.00
  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => just-arrived [3] => 75-hp-granulators )
  • Stock#: 17722

    USED CUMBERLAND 2050B GRANULATOR


    Cumberland model 2050B granulator, S/N 51310-6928, 20″ x 50″ feed throat, 5 knife 130mm steep angle rotor, 2 bed knife, conveyor in-feed hopper, 100 HP 208-230/460-volt 1775 RPM motor, 10″ OD airveyor discharge, mounted to a 36″ tall leg base, starter & controls not included.

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17694

    USED WERNER & PLEIDERER 83mm TWIN SCREW EXTRUDER


    83 mm Werner & Pfleiderer co-rotating twin screw extruder. Has 36/1 L/D barrel, driven by 200 hp dc motor with SCR control. Includes temperature control panel. No side feeder. Serial #136255.

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17702

    USED WERNER & PFLEIDERER ZSK20 TWIN SCREW EXTRUDER


    Werner & Pfleiderer Model ZSK20 20mm co-rotating twin screw extruder. S/N 02-3108-1000-010-1, Has 40:1 L/D barrel at a 43″ centerline driven through a 16.2:1 gearbox with a 37 newton meter torque capacity per screw shaft, extruder is powered by a 5 HP A/C motor with Allen Bradley 1336 Impact Drive unit, 588 RPM screw speed. Includes Brabender 1/2 HP model MS-FW40/Oplus-70 feeder, spare used motor and gearbox in unknown condition. Extruder manufactured 3/2003

    $0.00
  • Array ( [0] => just-arrived [1] => extruders-twin-screw [2] => just-arrived [3] => extruders-twin-screw )
  • Stock#: 17698

    USED WERNER & PFLEIDERER ZSK40 TWIN SCREW EXTRUDER


    Werner & Pfleiderer Model ZSK40 40mm co-rotating twin screw extruder, S/N 180399, 1990 model year, 46:1 L//D vented barrel with 11 barrel sections and a 41″ centerline. Driven by a 50 HP 500-volt 1750/2100 RPM D/C motor and SCR Control with a screw speed of 517 RPM. Includes Acrison 1.5 HP weight loss differential feeder, 2.2 KW Tervac vacuum pump, and side feeder.

    $0.00