One (1) used Nissei model NEX100-9E injection molding machine. Unit has a clamping force of 80 tons and an approximate shot capacity of 3.04 ounces. All electric machine. Tact control. 15.15″ x 15.15″ tie bar spacing. Platens measure 21.45″ x 21.45″. 7.87″-15.15″ mold thickness range. in 2012. Serial Number H08Y376. Manufactured 5/2004. 230/3/60. Used for lab testing of material.
McQuay model WGZ040AA27-ER10 global scroll water cooled chiller. S/N STNV080500269. 40 tons nominal via four ten-ton compressors in two circuits of 25/ 50 /75 unloading steps with remote condenser. 47 lbs. R407C refrigerant each circuit. 2005 model year. Special handling required: spreader bars must be used to prevent damage to the copper tubing in both the chiller unit and condenser during unloading and installation. The procedure is included in the manual. Standard flatbed required for shipment.
One (1) used Welex 3.5″ 30:1 L/D extruder. Electrically heated water cooled (closed loop) and vented barrel at an approximate 69″ center line height. Center line height can be reduced approximately 8″ by removing an additional base. Lufkin change gear gearbox is direct driven in a tuck under manner by a 150 HP Emerson DC motor with Control Technique Mentor II SCR control. Present reduction ratio is 13.89:1. Includes integral panel having fourteen (14) zones of temperature control. Dynisco model EH-35 screen changer with 3 HP hydraulic pack is mounted on the extruder discharge. Screen changer S/N EH-35208. Also includes 20 HP melt pump with controls. Unit was updated and the screen changer and melt pump where added 2002. Overall dimensions are 18′ x 6′ x 103″
One (1) Used Metalmecanica Rossi model MV stainless steel screw blender. S/N 0102. Blender is 5′ diameter x 10′ straight side x 6′ cone bottom. Includes (2) 4″ top mounted inlets and a 10″ x 12″ bottom outlet. Blender has an approximate total vessel volume of 230 cubic feet and a working capacity of 200 cubic feet. Center enclosed screw is driven by 15 HP (11 kw) motor. Discharge includes air actuated valve and Eriez model 10.5″ x 8″ TGH-2 metal catcher. Swing open access hatch. Does not included legs. Manufactured in 2014.
One( 1) used Extrusion Dies Inc. model Ultra-flex HRC 300 sheet die with Fast Gap having a 90″ slot opening. Integral upper flexible lip is adjustable, removable lower lip. 45 degree restriction bar. Adjusting bolts on 1″ centers. .300 gap .adjustment. Coat-hanger manifold. 1 ½” back center feed. Fast gap needs repair, but die can be used without the fast gap. Manufactured in 1995. S/N 95-17703. Weighs 4236 pounds.
One (1) used Conair model W2400 dehumidifying dryer rated at 1500-3000 pounds an hour. Approximately 2000 CFM. 150-375 degrees Fahrenheit temperature range. 15 HP blower. 8″ OD outlet. 460/3/60 operation. 56.7 FLA. Manufactured in 2007. 4′ x 7′ x 90″. S/N 20205. Offered less hopper.
One (1) used Gala model 5MUP underwater pelletizing system. Includes 2 HP cutter with four (4) blade hub, three (3) spare dies, 40 GPM TWS-40 water system with heater, pump, heater exchanger, 5 HP model 8.2 BF dryer, and non-OEM custom control panel. S/N 8801458
Nelmor shredder / granulator system consisting of: One (1) Nelmor model V2727 shredder. S/N 8502-22370. 4-shaft shredder with 18 replaceable and sharpen-able cutter inserts per shaft. Powered by a 30 HP 230/460-volt 1765 RPM motor. Cutting chamber is 27.5″ wide x 32″ deep. Insulated in-feed hopper has a 34.5″ x 46″ opening with an in-feed height of 91″. Includes Nelmor model G1220M1 granulator. S/N 8502-22187. 3 knife open rotor with 2 bed knives. Powered by a 20 HP 230/460-volt motor. Has 6″ airveyor discharge and is mounted on casters. Includes single stand alone control panel that operates both the shredder and the granulator. Was used for HDPE blow molded parts.
Pallman model PX315 Pulverizer, S/N 15480021, 12″ diameter rotor powered by a 40 HP 460-volt 3545 RPM motor with a scale up factor of 1.0. 20″ long x 4″ wide Eriez model 20A vibratory feeder with metal catcher on 8″ pipe discharge. 5 HP 230/460-volt 3450 RPM New York blower that includes New York model N15P5 silencer. Has Vibco model SCR-200 vibratory unit on hopper. Also includes Flex-Kleen model 84-BVS-16III dust collector with blowback and cyclone that includes .33 HP 208-230/460-volt 1745 RPM airlock. Unitized control panel mounted to machine frame. Excellent for pulverizing medium hard to soft materials. Can produce particles 325-35 mesh
Sheer Bay Plastics Machinery Model SGS-300-A 12″ strand pelletizer. S/N SA305-003. Dual motor driven by approximate 15 HP rotor motor and 10 HP pull roll motor. 460/3/60 A/C input. Includes 60 knife helical rotor installed. Includes spare sharpened 60 knife rotor as well as the manual and three (3) spare rubber rolls. Good condition.
One (1) used 4″ 30:1 L/D ratio PTI model 4000 extruder having a five (5) zone electrically heated, water cooled (closed loop), vented, and plugged barrel at a 53″ center-line height. Flender model E2HA7 gearbox has a reduction ratio of 11.807:1 and is rated at 150 HP. The gearbox is direct driven out the back end by a 150 HP ABB motor with ABB inverter. Gearbox has an oil pump and heat exchanger. The extruder has a water-cooled feed throat with 4″ x 6″ on center entrance. The temperature control panel has five (5) zones for the barrel and fifteen( 15) zones of temperature controls for die zones. Inverter, temperature panel and 5 HP hydraulic power pack for the screen changer are mounted on the sane base as the extruder. Includes Xaloy model EH-45 hydraulic slide plate screen changer, S/N 740. Extruder S/N 4390/1069. Manufactured 2/2007. 460/3/60 input power