Array ( [0] => just-arrived [1] => injection-molding [2] => just-arrived [3] => injection-molding )
  • Stock#: 17919

    USED NISSEI NEX100-9E 80 TON INJECTION MOLDER


    One (1) used Nissei model NEX100-9E injection molding machine. Unit has a clamping force of 80 tons and an approximate shot capacity of 3.04 ounces. All electric machine. Tact control. 15.15″ x 15.15″ tie bar spacing. Platens measure 21.45″ x 21.45″. 7.87″-15.15″ mold thickness range. in 2012. Serial Number H08Y376. Manufactured 5/2004. 230/3/60. Used for lab testing of material.

  • Array ( [0] => just-arrived [1] => chillers [2] => just-arrived [3] => chillers )
  • Stock#: 17935

    USED MCQUAY 40 TON WATER COOLED CHILLER


    McQuay model WGZ040AA27-ER10 global scroll water cooled chiller. S/N STNV080500269. 40 tons nominal via four ten-ton compressors in two circuits of 25/ 50 /75 unloading steps with remote condenser. 47 lbs. R407C refrigerant each circuit. 2005 model year. Special handling required: spreader bars must be used to prevent damage to the copper tubing in both the chiller unit and condenser during unloading and installation. The procedure is included in the manual. Standard flatbed required for shipment.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17954

    USED WELEX 3.5″ 30:1 L/D 150 HP EXTRUDER


    One (1) used Welex 3.5″ 30:1 L/D extruder. Electrically heated water cooled (closed loop) and vented barrel at an approximate 69″ center line height. Center line height can be reduced approximately 8″ by removing an additional base. Lufkin change gear gearbox is direct driven in a tuck under manner by a 150 HP Emerson DC motor with Control Technique Mentor II SCR control. Present reduction ratio is 13.89:1. Includes integral panel having fourteen (14) zones of temperature control. Dynisco model EH-35 screen changer with 3 HP hydraulic pack is mounted on the extruder discharge. Screen changer S/N EH-35208. Also includes 20 HP melt pump with controls. Unit was updated and the screen changer and melt pump where added 2002.  Overall dimensions are 18′ x 6′ x 103″

  • Array ( [0] => just-arrived [1] => mixers [2] => just-arrived [3] => mixers )
  • Stock#: 17929

    USED METALMECANICA ROSSI STAINLESS MIXER


    One (1) Used Metalmecanica Rossi model MV stainless steel screw blender. S/N 0102. Blender is 5′ diameter x 10′ straight side x 6′ cone bottom. Includes (2) 4″ top mounted inlets and a 10″ x 12″ bottom outlet. Blender has an approximate total vessel volume of 230 cubic feet and a working capacity of 200 cubic feet. Center enclosed screw is driven by 15 HP (11 kw) motor. Discharge includes air actuated valve and Eriez model 10.5″ x 8″ TGH-2 metal catcher. Swing open access hatch. Does not included legs. Manufactured in 2014.

    6 Available

  • Array ( [0] => just-arrived [1] => extrusion-sheet-dies [2] => just-arrived [3] => extrusion-sheet-dies )
  • Stock#: 17966

    USED EDI HRC300 90″ SHEET DIE


    One( 1) used Extrusion Dies Inc. model Ultra-flex HRC 300 sheet die with Fast Gap having a 90″ slot opening. Integral upper flexible lip is adjustable, removable lower lip. 45 degree restriction bar. Adjusting bolts on 1″ centers. .300 gap .adjustment. Coat-hanger manifold. 1 ½” back center feed. Fast gap needs repair, but die can be used without the fast gap. Manufactured in 1995. S/N 95-17703. Weighs 4236 pounds.

  • Array ( [0] => just-arrived [1] => dryers-500-3500-cfm [2] => just-arrived [3] => dryers-500-3500-cfm )
  • Stock#: 17978

    USED NOVATEC MPC-1750 DRYER AND HOPPER


    One (1) used Novatec model MPC-1750 twin tower desiccant dryer rated at 1750 CFM. Control panel is mounted on the same base as the dryer. With free standing heater box and nominal 15,000 pound capacity hopper with lid, plenum and stand.  S/N 12-034-3367. 460V/3/60Hz input.  254 amps, 211 KVA, Manufactured in 2004

  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => just-arrived [3] => 75-hp-granulators )
  • Stock#: 17982

    USED CUMBERLAND 2050B GRANULATOR


    Cumberland model 2050B granulator. S/N 51310-95013. 20″ x 50″ feed throat. 3 knife high shear hard-faced and water cooled rotor. 2 bed knives on water cooled bed blocks. 125 HP 460-1780 RPM motor. Modified conveyor feed hopper with 17″ x 8″ opening and plate magnet. Airveyor discharge has 8″ (OK200) outlet that can removed to return to standard 10″ OD. Hard faced chamber doors and bed shields. Air purge bearings. 1/8″ screen installed. Mounted on a step base. Includes Schneider Electric soft starter with enclosure.

  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => just-arrived [3] => 75-hp-granulators )
  • Stock#: 17975

    USED RAPID W1836 GRANULATOR SYSTEM


    Rapid model W1836 granulator. S/N 500.84751.001 20. 18″ x 36″ feed throat. 3 knife open rotor, 2 bed knife. Super-T tangential cutting chamber. 75 HP 460-volt motor. Insulated conveyor feed hopper with 1 3/4 HP power jack back. Insulated body panels. 6″ right or left hand airveyor discharge mounted on vibration pads. Includes Laros model E515-36-1306-48 conveyor. S/N E5153270-065888. 1 HP 460-volt motor. 34″ wide belt x 161″ long plus 48″ top horizontal section. 2.25″ tall cleats on 52″ centers. Caster conveyor stand also includes stand-alone starter/control panel for the granulator, hopper jack back, and the conveyor. Granulator mounted e-stop. Manufactured 9/2006. Also includes Sterling #6 blower, #8 cyclone, and #8 cyclone stand.

  • Array ( [0] => just-arrived [1] => balers [2] => just-arrived [3] => balers )
  • Stock#: 18003

    USED EXCEL EX60 BALER


    Excel model EX60 automatic closed end baling press. S/N EX1091. 150″ x 75″ x 62″ machine size. 48″ x 60″ x 30″ chamber. 60″ x 48″ x 30″ bale. 54″ x 35″ charge chamber opening. 2500 PSI hydraulic system pressure with 124,400 lbs. overall platen force. 40 second cycle time. 34-gallon hydraulic piston pump. Two 6″ bore 54″ stroke hydraulic cylinders. 105-gallon oil reservoir. Powered by 20 HP 230/460 3 phase motor. NEMA 12 controls. Includes 48″ wide x 23′ long in-feed conveyor with 3″ cleats on 30″ centers. S/N C1064. Powered by approximate 5 HP motor with Reliance A/C variable speed drive. Baler is manual tie. Refurbished by Excel (OEM) in 2012.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17995

    USED BRAMPTON 4.524:1 AC/HB 4.5″ 24:1 EXTRUDER


    One (1) used 4.5″ 24:1 L/D ratio Brampton Engineering model 4.5 24/1 AC HB extruder. Five (5) zone electrically heated,air-cooled, non-vented barrel at a 42″ center-line height. Center-line height is adjustable via hand-wheel. Heavy duty gearbox is belt driven in a wraparound manner by a 250 HP Reliance motor with SCR control. The extruder has a water-cooled feed throat with 4.75″ x 6.5″ on center entrance. The temperature control panel has five (5) zones for the barrel and four (4) zones of temperature controls for die zones. Extruder S/N 85.96926. 460/3/60 input power. Temp panel 125 FLA. Last used on HDPE for corrugated pipe.

  • Array ( [0] => just-arrived [1] => extrusion-screen-changers [2] => just-arrived [3] => extrusion-screen-changers )
  • Stock#: 17999

    USED GNEUSS SFX75 3″ CONTINUOUS SCREEN CHANGER


    Gneuss model SFX75 3″ continuous screen changer. S/N. 02083047. 460/3/60 operation. Includes PLC control panel

  • Array ( [0] => just-arrived [1] => pelletizers [2] => just-arrived [3] => pelletizers )
  • Stock#: 17908

    USED GALA 5MUP UNDERWATER PELLETIZING SYSTEM


    One (1) used Gala model 5MUP underwater pelletizing system. Includes 2 HP cutter with four (4) blade hub, three (3) spare dies, 40 GPM TWS-40 water system with heater, pump, heater exchanger, 5 HP model 8.2 BF dryer, and non-OEM custom control panel. S/N 8801458