-
Stock#: 17455
USED CONAIR 5308 8″ PELLETIZER
Used 8″ Conair Jetro Model 5308 strand pelletizer with dual drive. Serial #12-080679. Has 24 knife bolt on style rotor. 460 volt, 3 phase, 60 hertz. Includes 2 hp motor for pull roll drive, 15 hp motor for rotor drive. Has air cylinder actuated nip rolls, currently mounted on base supplying 94″ feed height.
-
Stock#: 17454
USED CUMBERLAND 8″ PELLETIZER
Used 8″ Cumberland “Quietizer” pelletizer. Serial #264550-98005. Driven by 15 hp AC motor, with variable frequency drive, 460 volt AC input. Has 48 knife helical style rotor, air cylinder actuated nip rolls. Includes spare helical rotor.
-
Stock#: 17439
USED CLOEREN HD-75 9″ SHEET DIE
Cloeren / Production Components model HD-75 9″ sheet die. Integral upper flexible lip and removable lower lip. Adjusting bolts on 1″ centers. Flex adjustment of 0.075″. Coat hanger manifold. Job number 0093-86. last ran dental products on a 2″ Welex extruder. Includes die cart.
-
Stock#: 17438
USED WELEX 2″ 24:1 L/D EXTRUDER
Welex model 200-24/1, 2″ 24:1 L/D extruder with a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 50″ centerline height. Gearbox is a Koellmann Gear and is belt driven by a 20 HP D/C motor with SCR control. D/C motor was recently replaced. Unitized temperature control panel with six (6) zones of controllers consisting of three zones for the barrel and three die zones. Swing gate on discharge. Gravity feed hopper. S/N 2235 3-83. 460V/3ph/60Hz input. Includes the documentation manual.
-
Stock#: 17437
USED DAVIS STANDARD 1/4″ TUBING EXTRUSION LINE
Davis Standard 1/4″ tubing extrusion line including the following equipment:
A. Davis Standard / Killion model KN-100 1.00″ 24:1 L/D extruder having a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 39″ centerline height. Gearbox is belt driven by a 3 HP D/C motor with SCR control. Unitized temperature control panel has six (6) zones of Eurotherm controllers consisting of three (3) zones for the barrel and three (3) zones for the c-clamp and die. C-clamp is mounted on the discharge. Includes gravity feed hopper. BOM number 05180. 230V/1ph/50-60Hz input, 47 FLA.
B. Nominal ¼” diameter electrically heated tubing die.
C. Davis Standard / Killion medical tubing vacuum tank measuring 116″ long with an 8″ x 8″ cross section. Stainless steel construction. Two glass doors. Upstream and downstream adjustment as well as up and down adjustment. Includes vacuum pump with 3 HP D/C motor, water pumps, sizing fixture, and controls. S/N 30176. 230V/1ph/60Hz input.
D. Davis Standard / Killion belt puller having a 2″ wide belt with 22″ of contact length. Powered by an approximate 1.5 HP D/C motor. Manually actuated top belt. S/N 30174. 230V/3ph/60Hz input, 10 FLA.
-
Stock#: 17433
USED NEW YORK 45GI 30 HP BLOWER
New York Blower Co model 45GI blower, 30 HP 230/460-volt motor, belt driven steel impeller, carbon steel construction, 13″ OD inlet, 8″ x 13″ rectangular outlet, blower type 224LS
-
Stock#: 17434
USED 20 HP BLOWER
Unknown manufacture approximate 20 HP blower, heavy duty housing, belt driven steel impeller, 11″ OD inlet, 12″ OD outlet
-
Stock#: 17435
USED MEDIUM STAINLESS STEEL CYCLONE
Medium size stainless steel cyclone, 8″ OD inlet, 10″ OD outlet, 16″ OD top opening, 33″ straight side barrel, 74″ long high angle cone, includes 3 leg stand
-
Stock#: 17425
USED MASTER DISCONNECT PANEL
Motor control center disconnect panel
-
Stock#: 16375
USED NELMOR RG1215P1 GRANULATOR
Nelmor model RG1215P1 granulator. 12″ x 15″ feed throat, 3 knife solid rotor, 2 bed knife, 15HP 230/460V motor. Insulated tray feed hopper and body panels. Includes blower and discharge cyclone.
Price: $7,500.00, as is.
-
Stock#: 17423
USED PURITAN VERTICAL SPOUT MAGNET
Puritan model VS288EZ vertical spout magnet having a 3.5″ inlet and outlet. Stainless steel construction. Engineered to remove fine to large ferrous contaminants from high volume, gravity fed product streams. Puritan’s Vertical Spout Magnets are ideally suited for products that would bridge or choke in a magnetic tube type separator. Ferrous contaminants are easily removed from products that are moist, lumpy, granular, or in powder form.
Vertical Spout Magnets consist of a housing and two opposing Plate Magnets. A center diverter on the housing inlet helps direct product towards the magnets. Ferrous contaminants are pulled from the flowing product and are captured by the powerful magnets. A Single Trap face design eliminates the possibility of the captured tramp metal being washed off back into the product stream.
Cleaning is achieved by releasing the latch assembly and pulling the drawer open. As the drawer is opened the magnets remain in a stationary position. Ferrous contaminants are transferred outside the product flow area where they are safely discarded. A specially designed angled drawer end ensures all contaminants are released outside of the product flow area. As product enters the stainless-steel housing, it is diverted towards two very large and powerful magnets that oppose each other. A Single Trap face design eliminates the possibility of contamination wash-off. -
Stock#: 17397
USED FERROMATIK MILACRON VISTA V55 MOLDING MACHINE
Ferromatik Milacron model Vista V55 injection molding machine. Unit has a clamping force of 55 tons and a 1.76 oz shot capacity. Toggle clamp. 12.8″ x 12.2″ tie bar spacing. Platens measure 20.08″ x 19.67″. Clean machine with 6170 original hours. Siemens Xtreem NT controller upgraded to Xtreem ST in 2017. S/N S55A0500076. Manufactured in 2002. College lab use. Manual included. 460/3/60 input. 6500 lbs. 11′ x 4′ x 6′
-
Stock#: 17396
USED STERLCO G9016-JO OIL MEDIA TEMPERATURE CONTROL
Sterlco model G9016-J0 single zone oil temperature control unit. 18 kw heater. 1 HP pump. With cooling and reversing options. 100 PSI maximum pressure. Very clean condition. S/N 97l5248. 480/3/60 input. 24 FLA. mounted on casters. Explosion proof controls.
-
Stock#: 17406
USED DAVIS STANDARD 6″ 30:1 L/D EXTRUDER
Davis Standard model 600STVW 6″ 30:1 L/D extruder, S/N 7-69006. Extruder has a five (5) zone electrically heated, water cooled non vented barrel at a 42″ center-line height. Gearbox has a reduction ratio of 17.38:1 and is rated at 300 HP at a service factor of 1.5. Gearbox was rebuilt by AES in august of 2014. Shaft mounted oil pump and filter. Gearbox is belt driven by a 300 HP 1150/2000 RPM field weakened D/C motor with SCR control. Water cooled feed throat has Conair mixer and bunting magnet mounted on the entrance. Temperature control panel has seven (7) zones of controllers. Cored extrusion screw with rotary union. C-clamp on the barrel discharge. Pulled from service 3/2021 as product line was discontinued
-
Stock#: 17408
USED GALA MAP-6 PELLETIZING SYSTEM
Gala model MAP-6 pelletizing system including cutter with 4 KW motor, die, and water box mounted on a stand, 40 GPM tempered water system with pump, reservoir, heater, heat exchanger and model 2008-BF spin dryer. Free standing OEM control panel. 460/3/60 input power. 64 full load amps. S/N 10200656. Manufactured in 2001. Last used with a 6″ 30:1 300 HP Davis Standard extruder
-
Stock#: 17409
USED BERINGER WRP-12 PELLETIZING SYSTEM
Beringer model WRP-12 pellet system including, 3 HP cutter head with die, water ring mounted on a portable cart, unitized water system consisting of sluice way, reservoir, 2 HP water pump, heat ex-changer, and Carter Day 2 HP spin dryer with blower, also includes stand-alone control panel. Manufactured in 1988
-
Stock#: 17411
USED CONAIR / MAGUIRE WSB-942T BLENDER
Conair / Maguire model WSB-942T four component blender, rated for up to approximately 4200 pounds per hour (material type and bulk density dependent). Includes additional Conair model F06 side feeder, four (4) Conair model DL-15 receivers and blender stand measuring 60″ x 60″ x 67″ that allows material to discharge into a gaylord. S/N MM102350-14. Manufactured in 2003, offered less controls.
-
Stock#: 17412
USED STERLCO G9016-J1 OIL MEDIA TEMPERATURE CONTROL
Sterlco model F9016-J1 single zone oil media temperature control unit. S/N 33E5598, 24 KW heater. 1HP pump. With cooling and reversing options. 100 PSI maximum pressure. very clean. 480/3/60 input. 31 FLA. mounted on casters
-
Stock#: 17413
USED FLEXICON BAG BREAKER STATION
Flexicon powder bag break station. Stainless steel construction with spray valve and dust collection, discharge via 4″ core-less auger with 5 HP motor
-
Stock#: 17414
USED BRABENDER FEEDER
Brabender loss in weight feeder, 1.5″ diameter screw discharge, mounted on load cells, 1/2 HP motor, approximate 2 cubic foot capacity stainless steel material bin, includes motor drive, controls, and Conair model DL-15 receiver