Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => shredders [3] => just-arrived [4] => 75-hp-granulators [5] => shredders )
  • Stock#: 18272

    USED WEIMA ZMK60 SHREDDER WITH GRANULATOR SYSTEM


    Weima four shaft shredder model ZMK60 with dual 25 HP 460-volt motors and controls. Has a 74″ x 55″ hopper opening with a 49″ wide rotor chamber. Includes a hydraulic operated ram feed assist with pump. S/N 900-985. Manufactured in 2005. Approximately 30″ wide discharge conveyor. Hydraulic gaylord box dumper. Cumberland model 1828B granulator with 3 rotor knives and tray feed hopper. S/N 49410-7330. Approximately 8″ OD inclined screw conveyor for grinder discharge.

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 18262

    USED VECOPLAN VAZ1100K SHREDDER


    Vecoplan model VAZ1100K single shaft rotary shredder. 10″ diameter x 42″ wide rotor with 27 cutters. Single position bed knife. Outboard bearing 120 RPM rotor is powered by a 30 HP 460-volt (22.7 Kw) motor. Has 3 HP (1.68 Kw) hydraulic ram. Gravity discharge approximately 27″ off the floor. 72″ x 82″ x 24″ base with fork-lift rails. In-feed hopper is 42″ wide and 8′ in length. Approximate 5/8″ holes screen. Has angled discharge chute with plate magnet. Includes machine mounted OEM control panel. 101.5″ x 103.75″ overall footprint. Approximately 7400 lbs. S/N 13060-010. 2015 model year.

  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => as-is-granulators-30-hp [3] => just-arrived [4] => 75-hp-granulators [5] => as-is-granulators-30-hp )
  • Stock#: 18256

    USED GRANUTEC TFG2548-XL100 GRANULATOR SYSTEM


    Granutec model TFG2548-XL100 granulator. S/N 1206.4438. 25″ X 48″ feed throat. 3 knife open rotor, 2 bed knife (6 pcs fly 4 pcs bed). Rotor driven by a 100 HP 230/460-volt 1190 RPM motor. Dual Flywheels. Tangential cutting chamber. Insulated tray feed hopper and body panels. 6″ OD right hand airveyor discharge. Mounted on forklift rails. Electronic jack screw assisted hopper tilt back and drop down for screen cradle. Complete with starter, controls, and disconnect. 2006 model year. System also includes Granutec 5 HP blower with 6″ OD inlet / outlet, steel impeller, and sound suppression enclosure. Also includes Granutec cyclone with 6″ OD inlet / 8″ OD outlet and lot of connecting pipe. Does not include a cyclone stand or filter-head.

  • Array ( [0] => just-arrived [1] => 35-60-hp-granulators [2] => just-arrived [3] => 35-60-hp-granulators )
  • Stock#: 18250

    USED CONAIR CK1831 GRANULATOR SYSTEM


    Conair model CK1831 (Rapid 1831K) granulator. S/N 70.1124. 18″ x 31″ feed throat. 3 knife open rotor, 2 bed knife. Dual Fly-wheel. Tangential cutting chamber. 60 HP 230/460-volt motor. Pneumatic assisted Insulated conveyor feed hopper with a 81.5″ in-feed height. 5/16″ holes screen installed. Right hand 6″ OD airveyor discharge with Kongskilde OK160 flange adapter. Mounted on vibration pads. Includes starter and controls with fused disconnect. Also includes Cincinnati Fan model PBS-15A 10 HP blower with directly driven steel reinforced impeller and heavy duty housing. S/N 112833-01. Blower has 6″ OD inlet and outlet with Kongskilde OK160 rolled flanges. Conair CM2000 cyclone with stand and 6 bag filter manifold (bags, bag clamps, and connecting pipe is not included). Equipment is in very good operational condition.

  • Array ( [0] => just-arrived [1] => 35-60-hp-granulators [2] => just-arrived [3] => 35-60-hp-granulators )
  • Stock#: 18249

    USED CONAIR CK1831 GRANULATOR SYSTEM


    Conair model CK1831 (Rapid 1831K) granulator. S/N 70.1104. 18″ x 31″ feed throat. 3 knife open rotor, 2 bed knife. Dual Fly-wheel. Tangential cutting chamber. 60 HP 230/460-volt motor. Pneumatic assisted Insulated conveyor feed hopper with a 81.5″ in-feed height. 5/16″ holes screen installed. Right hand 6″ OD airveyor discharge with Kongskilde OK160 flange adapter. Mounted on vibration pads. Includes starter and controls with fused disconnect. Also includes Cincinnati Fan model PBS-15A 10 HP blower with directly driven steel reinforced impeller and heavy duty housing. S/N 111878. Blower has 6″ OD inlet and outlet with Kongskilde OK160 rolled flanges. Conair CM2000 cyclone with stand and 6 bag filter manifold (bags. bag clamps, and connecting pipe is not included) Equipment is in very good operational condition.

  • Array ( [0] => just-arrived [1] => extrusion-screen-changers [2] => just-arrived [3] => extrusion-screen-changers )
  • Stock#: 18228

    USED HITECH 4.75″ CONTINUOUS SCREEN CHANGER


    One (1) used 4.75″ Hitech continuous screen changer. S/N 101154. Unit operates in a fully automatic mode, requiring no operator attention. The force of the extruder head pressure is used to move the filter screen. Having no moving parts or mechanism, there is nothing to wear, no associated downtime for maintenance. The only element that moves in a HITECHT screen changer is the screen itself. There are no hot breaker plates or dirty screen packs to handle. Screens are furnished in 120′ (36 meter) long rolls that have an effective filtration area equivalent to many hundreds of individual screen packs and typically last several months in non-stop operation. The automatic movement of the filter screen is set to cycle at a rate which smoothly blends with the melt flow. In addition, the rate of screen advancement automatically adjusts to correspond to fluctuations in extruder head pressure resulting from clogged screen. In this way, perfectly uniform head pressures and melt temperatures are maintained throughout months of non-stop operation. Cold circulating water is used to form perfectly leak-proof polymer seals. As a result, these machines are not subject to the leakage problems normally associated with other types of screen changers. Screen changer manufactured 9-25-2014. Controls new in 2021. 230/1/60. Last used on a 4.5″” Gloucester extruder with c-clamp.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 18227

    USED GLOUCESTER 4.5″ 30:1 250 HP EXTRUDER


    One (1) used Gloucester model 244-001 4.5″ 30:1 L/D extruder having an electrically heated, air cooled, and non-vented barrel at an approximate 56″ center line height. Cool Touch heaters with integral blowers were recently installed. Gearbox is direct driven in a wrap-around manner by a 250 HP Leeson A/C motor with Yaskawa A1000 inverter. Includes integral panel having fourteen (14) zones of temperature controls. Manufactured in 1980 and reconditioned in the last several years. C clamp on the discharge. S/N 244-244-24248-02. Last used to extrude HDPE sheet. 460/3/60 input power.

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 18240

    USED VECOPLAN VAZ160/200SL SHREDDER


    Vecoplan model VAZ160/200SL shredder. S/N 6277010. Belt driven 25″ diameter 414 RPM rotor with 62 60mm cutters. Powered by a 250 HP 460-volt motor. 63″ x 78″ Hopper opening. Hydraulic ram feed. Includes stand alone control panel and hydraulic pump for ram. Rated 4-20,000 lbs per hour throughput

    This shredder is designed specifically for re-shredding and reduction of very bulky materials such as loose plastic film, loose paper products, loose textiles, and light wooden products.

  • Array ( [0] => just-arrived [1] => extrusion-roll-stacks-rolls [2] => just-arrived [3] => extrusion-roll-stacks-rolls )
  • Stock#: 18226

    USED GLOUCESTER 66″ COOLING ROLL STAND


    One (1) used 66″ Gloucester cooling and polishing stand having three (3) nominal 20″ diameter chrome plated rolls mounted in a vertical arrangement for down stack operation at a 56″ center-line height. Includes two additional chrome rolls for additional cooling. Rolls are hydraulically actuated via 3 HP hydraulic pump. Chrome rolls are driven by via silent chain and sprockets via a 3 HP A/C motor through a four speed gear reducer. Includes 66″ pull roll stand with 4 speed transmission and 3 HP drive system. Includes idler conveyor built onto the frame. Also includes a five-zone water temperature control system with heaters, heat exchangers, pumps, and inline slitting provision. One chrome roll replaced last year at a cost of $30,000. Pulled from service due to plant closure 12/ 2022. S/N 24148-16. 460/3/60. Manufactured 3-8-80. Unit has been continuously updated. Temp system should be updated.

  • Array ( [0] => just-arrived [1] => blenders [2] => just-arrived [3] => blenders )
  • Stock#: 18223

    USED CONAIR / MAGUIRE WSB-940 6 COMPONENT BLENDER


    Conair / Maguire model WSB-940 six component blender. S/N MM100595-14. Main mixer is powered by a 1/4 HP 115-volt motor. Up to 3,200 lbs. per hour capacity (material type and bulk density dependent). Includes Maguire 100 recipe controller

  • Array ( [0] => just-arrived [1] => cast-film-lines [2] => extruders-34-3 [3] => lab-testing-equipment [4] => just-arrived [5] => cast-film-lines [6] => extruders-34-3 [7] => lab-testing-equipment )
  • Stock#: 18099

    USED COLLINS .75″ LAB CAST FILM LINE


    Used Collin laboratory blown film and cast film line. Type “Teach-Line”. Includes approximately .75″ extruder with 30:1 L/D. Extruder is equipped with melt pump, 1-3/8″ blown film die with air ring, 8″ wide nip roll mounted in tower (Serial #9550-50-06) with collapsing frame and single position winder. Extruder is electrically heated and air cooled and includes a stainless steel hopper. Also included is a 7.5″ wide 3-roll casting station, 2 of the 3 rolls are nipping and 1 is offset. Package is equipped with a single position winder and a 5″ wide adjustable lip cast film die mounted on stand. Die is Doctor Collins 160 x 70 x 80, Serial #02085200263

  • Array ( [0] => just-arrived [1] => shredders [2] => just-arrived [3] => shredders )
  • Stock#: 18197

    USED VECOPLAN RG52/100SPK SHREDDER


    Vecoplan model RG52/100SPK single shaft shredder. S/N 5542010. 15″ diameter rotor with sixty 40mm index-able crown cutters. Four pc counter knife set. 90 HP (67.11 kw) 460-volt 1778 RPM drive motor thru a Falk model 5407 gear box with a 13.89 gear ratio. Hydraulic ram is powered by a 7.5 HP hydraulic pump built in 2010. Hopper has a top opening of 115″ x 73″. Includes OEM starter panel with PLC and Weg soft starter.

  • Array ( [0] => just-arrived [1] => high-intensity-mixers [2] => just-arrived [3] => high-intensity-mixers )
  • Stock#: 18073

    USED HENSCHEL 500 LITER HIGH INTENSITY MIXER


    Used 500 liter Henschel high intensity mixer including air actuated discharge valve and belt driven motor.

  • Array ( [0] => just-arrived [1] => new-cumberland-granulators [2] => just-arrived [3] => new-cumberland-granulators )
  • Stock#: 48250-22010

    NEW CUMBERLAND X1400 GRANULATOR


    Cumberland model X1400 granulator, S/N 48250-22010, 24″ x 56″ feed throat, 5 knife twin shear rotor, 2 bed knives.  150 HP 460-volt motor.  Hydraulic assisted conveyor infeed hopper and screen cradle, mounted on floor level plate, 12″ airveyor discharge, 2022 model year.


  • Array ( [0] => just-arrived [1] => pulverizers [2] => just-arrived [3] => pulverizers )
  • Stock#: 18043

    USED CMS10 MILLING/PULVERIZING SYSTEM


    One (1) used CMS10 classified milling system. Package includes Micro #10 stainless steel pulverizer with 10 HP motor, air pulse type dust collector with five (5) port manifold and rotary valve, two (2) Azo classifiers, Tec Weigh volumetric feeder, two (2) cyclones, various elbows and piping and free-standing control panel for the system. S/N 8093-2. 460/3/60 operation. 60 amps maximum load. Last used on grinding powder coatings.

  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => just-arrived [3] => 75-hp-granulators )
  • Stock#: 17982

    USED CUMBERLAND 2050B GRANULATOR


    Cumberland model 2050B granulator. S/N 51310-95013. 20″ x 50″ feed throat. 3 knife high shear hard-faced and water cooled rotor. 2 bed knives on water cooled bed blocks. 125 HP 460-1780 RPM motor. Modified conveyor feed hopper with 17″ x 8″ opening and plate magnet. Airveyor discharge has 8″ (OK200) outlet that can removed to return to standard 10″ OD. Hard faced chamber doors and bed shields. Air purge bearings. 1/8″ screen installed. Mounted on a step base. Includes Schneider Electric soft starter with enclosure.

  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => as-is-granulators-30-hp [3] => just-arrived [4] => 75-hp-granulators [5] => as-is-granulators-30-hp )
  • Stock#: 18022

    USED CUMBERLAND X1400 GRANULATOR


    Cumberland model X1400 granulator. S/N 48250-05014. 24″ x 56″ feed throat. 3 knife twin shear rotor, 2 bed knife. 150 HP 460-volt 1775 RPM motor. Conveyor in-feed hopper with electronic jack back assist. 10″ left hand airveyor discharge. Electronic jack assisted drop down screen cradle. Includes soft starter control panel.

  • Array ( [0] => just-arrived [1] => 75-hp-granulators [2] => just-arrived [3] => 75-hp-granulators )
  • Stock#: 18021

    USED CUMBERLAND X1400 GRANULATOR


    Cumberland model X1400 granulator. S/N 48250-12004. 24″ x 56″ feed throat. 5 knife twin shear rotor, 2 bed knife. 150 HP 460-volt 1785 RPM motor. Hydraulic assisted tilt back conveyor in-feed hopper. Hydraulic assisted drop down screen cradle. 12″ OD airveyor discharge.  Starter and controls not included

  • Array ( [0] => just-arrived [1] => extrusion-sheet-dies [2] => just-arrived [3] => extrusion-sheet-dies )
  • Stock#: 17966

    USED EDI HRC300 90″ SHEET DIE


    One( 1) used Extrusion Dies Inc. model Ultra-flex HRC 300 sheet die with Fast Gap having a 90″ slot opening. Integral upper flexible lip is adjustable, removable lower lip. 45 degree restriction bar. Adjusting bolts on 1″ centers. .300 gap .adjustment. Coat-hanger manifold. 1 ½” back center feed. Fast gap needs repair, but die can be used without the fast gap. Manufactured in 1995. S/N 95-17703. Weighs 4236 pounds.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 18037

    USED EGAN 6″ 30:1 L/D 400 HP EXTRUDER


    One (1) used Egan 6″ 30:1 L/D extruder. S/N 37910. Having an electrically heated, water cooled (closed loop), and vented barrel at an approximate a 42” center line height.  Water system is incomplete. Philadelphia gearbox is set up for a direct driven in a wrap under manner by a 400 HP GE D/C motor. Present reduction ratio is 17.5:1. This gearbox requires repair. An uninstalled and rebuilt Philadelphia gearbox with a 16:1 reduction ratio is included. Gearbox was rebuilt by Philadelphia. 6” On center round feed throat entrance. 12.5” x 12.5” flange on feed throat.  Overall dimensions are 270” x 73” x 72”. Missing vent stack. Offered less SCR and temperature control panel.