Array ( [0] => uncategorized [1] => uncategorized )
  • Stock#: 3009

    RAMCO VACUUM 50 LB CAPACITY RECEIVER


    RAMCO MATERIAL RECEIVER 50 LB CAPACITY, 1-1/2″ ID INLET

  • Array ( [0] => uncategorized [1] => uncategorized )
  • Stock#:

    FIBERGLASS TOWERS


    Cooling Towers 45 to 540 Tons

    Temptek tower cells are designed to cool water through evaporation. Cooling towers are part of a central system (complete with a pump tank station). Tower cells supply temperatures to 85° (depending on ambient air heat and humidity) and are installed outside the plant building, either elevated on a stand or mounted on the roof. These tower cells are made of durable UV protected fiberglass with a counter air flow design.

    TOWER DESIGN:
    • Single or multi cell designs
    • Total non-ferrous construction materials
    • Single inlet and drain connections on models up to 270 tons
    • Induced draft air movement
    • Structural galvanized steel base on 45 to 135 ton models
    • Structural painted steel base on 170 to 540 ton models

    SHELL CONSTRUCTION:
    • High strength fiberglass molding
    • 1/2” of structural thickness in reinforced areas
    • UV stabilized coating
    • Acrylic adhesive bonding between shell halves
    • Polyurethane sealant

    FAN:
    • Air foil shaped blades for increased air flow
    • Blades are made of a glass fiber reinforced polymer
    • Direct drive
    • Factory set for maximum air movement

    MOTOR:
    • TEFC construction
    • Mounted on a stainless steel frame
    • Supported on reinforced fiberglass shell area
    • Mounted to shell with stainless steel fasteners

    INLET LOUVERS:
    • PVC construction
    • Easily removed for cleaning
    • Vertical orientation to eliminate ‘splash out’
    • Directs air flow at proper angle for even distribution
    • Helps prevent air-born debris from entering cell

    DISTRIBUTION HEADER:
    • Non-ferrous PVC ‘cross’ construction
    • Stationary
    • Computer designed spray pattern
    • Large orifice spray heads
    • PVC spray heads
    • Drift eliminator prevents over spray and water loss

    WET DECK:
    • Stacked honeycomb pattern maximizes water and air flow for greater cooling efficiency
    • PVC construction

    INSPECTION COVERS:
    • Easily removed
    • Seamless gasket sealing
    • Allows for inspection of cell interior and replacement of wet deck

    WARRANTIES:
    • 10 year shell warranty
    • 5 year motor/fan warranty

    OPTIONS:

    FAN STARTER KIT:
    • Motor starter contactor
    • Motor overload relay
    • Nema 1 enclosure
    • Fan thermostat

    SIDE OUTLET:
    • PVC flange
    • Factory installed

    BASIN FLOAT VALVE:
    • Mechanical float and valve
    • 1/2” supply connection
    • Factory or field installed

    TOWER STAND:
    • 10’ corner post design with cross bracing
    • Ladder and railing attachments

    TP SERIES SPECIFICATIONS

    MODEL
    T45P
    T85P
    T105P
    T135P
    T170P
    T210P
    T270P
    T315P
    T405P
    T540P
    CAPACITY TONS
    45
    85
    105
    135
    170
    210
    270
    315
    405
    540
    CAPACITY FLOW RATE GPM
    135
    255
    315
    405
    510
    630
    810
    945
    1215
    1620
    FAN QUANTITY
    1
    1
    1
    1
    2
    2
    2
    3
    3
    4
    FAN RPM
    1170
    1170
    1170
    870
    1170
    1170
    870
    1170
    870
    870
    # BLADES PER FAN
    9
    9
    9
    6
    9
    9
    6
    9
    6
    6
    FAN DIAMETER
    36
    42
    42
    60
    42
    42
    60
    42
    60
    60
    TOTAL CFM
    12040
    21700
    25000
    30500
    43400
    50000
    61000
    78388
    91500
    122000
    # MOTORS
    1
    1
    1
    1
    2
    2
    2
    3
    3
    4
    TOTAL HP
    3
    5
    10
    7.5
    10
    20
    15
    30
    22.5
    30
    FULL LOAD AMPS @ 230 / 3 / 60
    9.6
    15.2
    28
    28
    28
    56
    56
    86.4
    84
    112
    FULL LOAD AMPS @ 460 / 3 / 60
    4.8
    7.6
    14
    14
    14
    28
    28
    43.2
    42
    56
    PIPE SIZE TO PROCESS
    3″
    4″
    4″
    4″
    6″
    6″
    6″
    2 X 6″
    2 X 6″
    2 X 6″
    PIPE SIZE FROM PROCESS
    4″
    6″
    6″
    6″
    10″
    10″
    10″
    2 X 10″
    2 X 10″
    2 X 10″
    DIMENSION HEIGHT
    138″
    138″
    143″
    140″
    138″
    143″
    140″
    143″
    140″
    140″
    DIMENSTION LENGTH
    60″
    84″
    84″
    96″
    145″
    145″
    169″
    217″
    254″
    338″
    DIMENSION DEPTH
    49″
    73″
    73″
    85″
    84″
    84″
    96″
    84″
    96″
    96″
    WEIGHT DRY LBS
    725
    1290
    1390
    1612
    2310
    2210
    3125
    4000
    4350
    5800
    WEIGHT OPERATING LBS
    1470
    3100
    3200
    4200
    5700
    5600
    7800
    10700
    11000
    15000
    WEIGHT SHIPPING LBS
    1100
    1580
    1680
    1950
    2310
    2710
    3125
    4000
    4350
    5800
  • Array ( [0] => uncategorized [1] => uncategorized )
  • Stock#:

    AIR COOLED 5 TO 30 TON


    Air Cooled Central Chillers 5 to 30 Tons

    Process liquid chillers are designed to circulate a fluid medium (typically water, or a water-glycol solution) through a process application for cooling and can supply temperatures between 20° to 65°F. Central units provide enough capacity to serve multiple process applications. Generally, central liquid chillers are offered in capacities from 5 to 180 tons and can serve several processes at once.

    Air cooled liquid chillers use ambient air to dissipate process heat. These units efficiently run in plant air temperatures between 60° to 95°F. Major benefits to air-cooled units are heat recovery (for supplemental heating), exhaust air ducting (for plant ventilation), and less operating expense.

    FEATURES 5 TO 30 TON UNITS

    TEMPERATURE RANGE:
    • 20°F – 65°F

    FRAME CONSTRUCTION:
    • Galvanized steel frame
    • Galvanized enclosure panels
    • Castors – for portability
    • Standard NPT process fittings

    REFRIGERANT CIRCUITS:
    • Scroll compressor
    • Full component insulation
    • Air-cooled condenser with finned tubes
    • Propeller fan induced air flow
    • Filter-drier
    • Liquid line solenoid valve
    • Refrigerant sight glass with moisture indicator
    • Thermostatic expansion valve
    • Brazed plate evaporator
    • Capacity control (via hot gas bypass)

    ELECTRICAL:
    • Compressor motor starter
    • Fused transformer
    • NEMA rated electrical cabinet
    • Power entry terminal block

    SYSTEM LIMIT DEVICES:
    • High pressure limit
    • Low pressure limit
    • Coolant freezestat
    • Internal compressor overload
    • Control circuit fuse

    WARRANTY:
    • 1 year on parts and labor

    CONTROLLER 5 TO 30 TON UNITS

    CF Series (standard instrument)
    • Continuous To Process temperature display
    • Selectable Setpoint temperature display
    • Illuminate ON/OFF power switch
    • Soft touch Setpoint selection keys
    • Bright and easy-to-read LCD Temperature display window
    • Machine Status Lights with Compressor and
    Capacity Control indication
    • Basic Machine Diagnostics with Refrigeration Fault
    indicating light

    ALL MODELS USE HERMETIC RECIPROCATING COMPRESSORS

    MODEL
    CAPACITY
    COMP HP
    REFRIDGERANT
    CONDENSOR
    CFM
    REQUIRED GPM @ 20 PSI
    (3-PHASE) FL AMPS 230V / 460V
    CONNECTIONS
    DIMENSIONS
    WEIGHT
    MA-5A
    5 TONS
    5
    410A
    2 X 1/3 HP FANS
    5000
    12
    28.2 @ 230V / 13 @ 460V
    1 1/4″ NPT
    60″ X 34″ X 40″
    800 LBS
    MA-7.5A
    7.5 TONS
    7.5
    410A
    2 X 1/2 HP FANS
    7500
    18
    39.7 @ 230V / 20.6 @ 460V
    1 1/4″ NPT
    60″ X 34″ X 40″
    900 LBS
    MA-10A
    10 TONS
    10
    410A
    2 X 3/4 HP FANS
    10000
    24
    57.3 @ 230V / 28.7 @ 460V
    1 1/4″ NPT
    60″ X 34″ X 56″
    1000 LBS
    MA-15A
    15 TONS
    15
    410A
    2 X 7.5 HP BLOWERS
    15000
    36
    90.6 @ 230V / 45.3 @ 460V
    1 1/4″ NPT
    60″ X 64″ X 56″
    1640 LBS
    MA-15FC
    15 TONS
    15
    410A
    2 X 7.5 HP FANS
    15000
    36
    90.6 @ 230V / 45.3 @ 460V
    1 1/4″ NPT
    60″ X 64″ X 56″
    1640 LBS
    MA-20A
    20 TONS
    20
    410A
    2 X 10 HP BLOWERS
    20000
    48
    119 @ 230V / 59.5 @ 460V
    1 1/2″ NPT
    102″ X 58″ X 70″
    1950 LBS
    MA-20FC
    20 TONS
    20
    410A
    2 X 10 HP FANS
    20000
    48
    119 @ 230V / 59.5 @ 460V
    1 1/2″ NPT
    102″ X 58″ X 70
    1950 LBS
    MA-25A
    25 TONS
    25
    410A
    1 – 15 HP BLOWER
    25000
    60
    146 @ 230V / 73 @ 460V
    2″ NPT
    102″ X 58″ X 70
    2050 LBS
    MA-30A
    30 TONS
    30
    410A
    1 – 20 HP BLOWER
    30000
    60
    179 @ 230V / 89.5 @ 460V
    3″ NPT
    102″ X 58″ X 70
    2250 LBS

    This article was composed with one of the best online HTML tools. Please purchase a htmlg membership to stop adding links to the edited documents.

  • Array ( [0] => uncategorized [1] => uncategorized )
  • Stock#:

    VTO Heat and Cool Series


    Oil Media VTO Series Heating & Cooling Temperature Control

    Temperature control units circulate a fluid medium (typically water or oil) through a process application for HEATING can supply temperatures between 30° to 400°F (depending on medium). Temperature controller units service only a single process at a time, but are designed to be moved between process applications as the need requires.

    A pump circulates high temperature oil through the process. An electric heater elevates the temperature of the oil. Cooling is achieved through ambient radiation or through the use of an optional heat exchanger. Units are available microprocessor control instrument, several heater KW ratings, and several optional cooling heat exchanger sizes.

    UNIT CONSTRUCTION
    • All galvanized sheet metal cabinetry
    • Upright design
    • Easy access lift-off panel
    • Hinged electrical panel
    • Portable, on casters
    • NPT female process connections

    CIRCULATING PUMP
    • Horizontal centrifugal pump
    • Water cooled pump seal (prolongs seal life)
    • ODP motor with high temperature bearings
    • Stainless steel motor shaft
    • Brass impeller
    • 500¾F carbon/niresist shaft seal
    • Custom cast pump casing accepts heater cycliner

    HEATING
    • Flanged bolt-in mount
    • Vertical orientation
    • Steel heater sheath
    • Mercury heater contactor

    ELECTRICAL
    • Nema 1 style electrical construction
    • 3 Phase service
    • 110 volt control circuit transformer
    • Control circuit fusing.

    LIMITS
    • Water supply pressure switch
    • Water supply pressure relief valve
    • Motor overload protection
    • Dual high temperature limits
    • Fused control circuit

    OPTIONS
    • Stainless steel heat exchanger for cooling

    WARRANTIES
    • 1 year parts and labor warranty

    CONTROLLER

    The VTO Series microprocessor control instrument offers stable process temperatures at setpoint, analog setpoint selection with machine status monitoring.

    Designed exclusively for Temptek hot oil temperature control units, the VTO Series Control is built on a microprocessor circuit design to offer functional simplicity to the process environment.

    TEMPERATURE DISPLAY:
    Bright 9-segment 3 digit display window that is easy to read at distance.

    CONTROL RANGE:
    100° – 400°F (38° – 202°C) control range.

    OPERATORS: The On/Off switch activates the unit. Setpoint temperature is selected by the analog selection dial

    INDICATORS: Operating status is indicated by the Power, Pump, Heat and Cool lights.

    WARRANTY: 1 year free replacement.

    MODEL
    HEATER
    HP
    GPM
    PSI
    AMPS @ 230V
    AMPS @ 460V
    PROCESS CONNNECTIONS
    SUPPLY/DRAIN CONNECTIONS
    DIMENSIONS
    WEIGHT
    VTO2100C
    12 KW
    1
    30
    24
    34.8
    17.9
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    275 LBS
    VTO2150C
    12 KW
    1 1/2
    45
    26
    36.4
    18.7
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    285 LBS
    VTO2200C
    12 KW
    2
    50
    28
    38.0
    19.5
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    300 LBS
    VTO2300C
    12 KW
    3
    60
    26
    46.6
    23.3
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    290 LBS
    VTO3100C
    16 KW
    1
    30
    24
    50.6
    25.4
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    580 LBS
    VTO3150C
    16 KW
    1 1/2
    45
    26
    47.0
    23.5
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    585 LBS
    VTO3200C
    16 KW
    2
    50
    28
    49.0
    24.5
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    595 LBS
    VTO3300C
    16 KW
    3
    60
    26
    21.0
    25.5
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    610 LBS
    VTO4100C
    24 KW
    1
    30
    24
    73.8
    36.9
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    625 LBS
    VTO4150C
    24 KW
    1 1/2
    45
    26
    75.8
    37.9
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    630 LBS
    VTO4200C
    24 KW
    2
    50
    28
    77.8
    38.9
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    635 LBS
    VTO4200C
    24 KW
    3
    60
    26
    71.0
    35.5
    1″ NPT
    1/2″ NPT
    44″ X 16″ X 24″
    645 LBS
  • Array ( [0] => uncategorized [1] => uncategorized )
  • Stock#:

    LS Series


    Water Media LS Series Temperature Control

    Temperature control units circulate a fluid medium (typically water or oil) through a process application for HEATING can supply temperatures between 30° to 400°F (depending on medium). Temperature controller units service only a single process at a time, but are designed to be moved between process applications as the need requires.

    A pump circulates water through the process. An electric heater and a cooling valve work together to control the water temperature. Theses units are portable and require a plant water supply source and are available with a variety of different control instruments, heater sizes, and cooling valves.

    UNIT CONSTRUCTION:
    • All stainless sheet metal cabinetry
    • Upright design
    • Easy access lift-off panel
    • Twin tank design
    • Hinged electrical panel
    • Portable, on casters

    CIRCULATING PUMP
    • Centrifugal type
    • Custom cast pump casing for
    increased flow
    • Bronze impeller
    • Energy efficient pump motor
    • Stainless steel motor shaft
    • Overload relay protection
    • Pump seal flush

    HEATING
    • Custom cast heater cylinder
    • Dual voltage heater
    • Flanged, bolt-in mount
    • Mercury contactor

    COOLING
    • Custom cast cooling cylinder
    • Solenoid valve, integral to
    cooling cylinder
    • Microprocessor controlled

    ELECTRICAL
    • Fused transformer
    • 10′ power cord,
    factory installed

    LIMITS
    • Water supply pressure switch
    • Pressure relief valve
    • High temperature limit
    • Fused control circuit

    WARRANTIES:
    • 1 year on parts and labor

    CONTROLLER

    TEMPERATURE DISPLAYS:
    Bright 9-segment 3 digit displays window that are easy to read at distance. The upper window shows To Process temperature. The lower window shows Setpoint temperature.

    CONTROL RANGE:
    30° – 250°F (0° – 120°C) control range.

    OPERATORS: The On/Off switch activates the unit. Setpoint temperature and other operating parameters are selected by the two soft key Arrow buttons. Unit Vent is activated by the Vent key.

    INDICATORS: Operating status is indicated by the Power, Pump, Heat and Cool lights.

    DIAGNOSTICS: Unit diagnostics is indicated by the Safety and Alarm lights. See manual for troubleshooting details.

    COMMUNICATIONS: Network communications is provided via the RS-422 port.

    WARRANTY: 2 year free replacement

    MODEL
    HEATER
    HP
    GPM
    PSI
    AMPS @ 230V
    AMPS @ 460V
    PROCESS CONNNECTIONS
    SUPPLY/DRAIN CONNECTIONS
    DIMENSIONS
    WEIGHT
    VT275LS
    10 KW
    3/4
    35
    30
    27.8
    13.9
    1 1/4″ NPT
    1/2″ NPT
    27″ X 11″ X 16″
    200 LBS
    VT2100LS
    10 KW
    1
    45
    30
    28.6
    14.3
    1 1/4″ NPT
    1/2″ NPT
    27″ X 11″ X 16″
    208 LBS
    VT2150LS
    10 KW
    1.5
    62
    30
    30.2
    15.1
    1 1/4″ NPT
    1/2″ NPT
    27″ X 11″ X 16″
    208 LBS
    VT2200LS
    10 KW
    2
    75
    30
    31.8
    15.9
    1 1/4″ NPT
    1/2″ NPT
    27″ X 11″ X 16″
    213 LBS
    VT2300LS
    10 KW
    3
    80
    30
    34.6
    17.3
    1 1/4″ NPT
    1/2″ NPT
    27″ X 11″ X 16″
    223 LBS
    VT375LS
    16 KW
    3/4
    35
    30
    42.8
    21.4
    1 1/4″ NPT
    1/2″ NPT
    27″ X 11″ X 16″
    205 LBS
    VT3100LS
    16 KW
    1
    45
    30
    43.6
    21.8
    1 1/4″ NPT
    1/2″ NPT
    27″ X 11″ X 16″
    210 LBS
    VT3150LS
    16 KW
    1.5
    62
    30
    45.2
    22.6
    1 1/4″ NPT
    1/2″ NPT
    27″ X 11″ X 16″
    210 LBS
    VT3200LS
    16 KW
    2
    75
    30
    48.8
    23.4
    1 1/4″ NPT
    1/2″ NPT
    27″ X 11″ X 16″
    220 LBS
    VT3300LS
    16 KW
    3
    80
    30
    49.6
    24.8
    1 1/4″ NPT
    1/2″ NPT
    27″ X 11″ X 16″
    225 LBS
  • Array ( [0] => uncategorized [1] => uncategorized )
  • Stock#:

    2000 SERIES CENTRAL-MEDIUM GRANULATORS


    Featuring Twinshear ® knife configuration to increase cutting efficiency, the 2000 Series granulators offer throughputs from 1800 lbs./hr up to 2600 lbs./hr. The granulators are easy to maintain, with a drop-down screen cradle and hydraulic tilt mechanism on the infeed hopper for quick and easy access to the cutting chamber and rotor. The 2000 Series’ low feed height and large widths are ideal for thermoforming, and a variety of infeed, discharge, and rotor options provide added flexibility for almost any application.

    STANDARD FEATURES:

    • Airveyor discharge provides continuous material evacuation
    • Twinshear ® knife configuration increases cutting efficiency
    • A drop down screen cradle provides quick screen access for simplified maintenance
    • Hydraulic tilt mechanism for the infeed hopper provides complete access to the cutting chamber and rotor
    • Low feed height and large widths are ideal for thermoforming

    Product Brochure

  • Array ( [0] => uncategorized [1] => uncategorized )
  • Stock#:

    CUMBERLAND 800X SERIES BESIDE-THE-PRESS


    The Cumberland 800X Series granulators are ideal for reject components from the injection, blow molding, and extrusion processes. The compact design makes them easily movable and the sound enclosure controls noise and permits access. Engineered for hand feed, robot feed or conveyor feed, these low speed granulators are packed full of standard features.

    STANDARD FEATURES:

    • Pivoting hopper, drop-down removable screen cradle and machined, bolted cutting chamber simplifies cleaning and maintenance.
    • Low profile, sound-attenuated infeed system for robot, hand or conveyor feed applications
    • HCHC knives manufactured in-house utilizing Cumberland’s proprietary process for heat-treating ensure durability and long life
    • Oversized solid flywheel

    Technical Specifications

    Product Brochure