Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 18227

    USED GLOUCESTER 4.5″ 30:1 250 HP EXTRUDER


    One (1) used Gloucester model 244-001 4.5″ 30:1 L/D extruder having an electrically heated, air cooled, and non-vented barrel at an approximate 56″ center line height. Cool Touch heaters with integral blowers were recently installed. Gearbox is direct driven in a wrap-around manner by a 250 HP Leeson A/C motor with Yaskawa A1000 inverter. Includes integral panel having fourteen (14) zones of temperature controls. Manufactured in 1980 and reconditioned in the last several years. C clamp on the discharge. S/N 244-244-24248-02. Last used to extrude HDPE sheet. 460/3/60 input power.

  • Array ( [0] => extruders-3-5-10 [1] => extrusion-miscellaneous [2] => extruders-3-5-10 [3] => extrusion-miscellaneous )
  • Stock#: 18238

    USED DAVIS STANDARD 6″ EXTRUDER GEARBOX ONLY


    One (1) used Davis Standard model 60IN60TPIH extruder gearbox. 17.21:1 gear ratio. Rated at 526 HP at a service factor of 1.5. S/N 06890. S/O 6890. Manufactured 6/21/1999. Gears are in beautiful condition. With heat exchanger.

  • Array ( [0] => extruders-3-5-10 [1] => extruders-3-5-10 )
  • Stock#: 18185

    USED AMERICAN KUHNE 100mm 30:1 L/D EXTRUDER


    One (1) used American Kuhne 100mm (3.94″) 30:1 L/D extruder. S/N 6882. Has (7) zone electrically heated, air cooled, and non-vented barrel at an approximate 42″ center line height. Gearbox is a Koellmann model Unex 5.0 and has a reduction ratio of 9:11 and is belt driven in a wrap around manner by a 100 HP A/C motor. Includes 10 HP Zenith melt pump on cart. Manufactured 11/2006

  • Array ( [0] => extruders-3-5-10 [1] => extruders-3-5-10 )
  • Stock#: 17940

    UNUSED DAVIS STANDARD 6″ FEED THROAT


    Davis Standard 6″ extruder feed throat only, very good unused condition. 1550 lbs shipping weight, 48 x 40 x 34 skid

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 18037

    USED EGAN 6″ 30:1 L/D 400 HP EXTRUDER


    One (1) used Egan 6″ 30:1 L/D extruder. S/N 37910. Having an electrically heated, water cooled (closed loop), and vented barrel at an approximate a 42” center line height.  Water system is incomplete. Philadelphia gearbox is set up for a direct driven in a wrap under manner by a 400 HP GE D/C motor. Present reduction ratio is 17.5:1. This gearbox requires repair. An uninstalled and rebuilt Philadelphia gearbox with a 16:1 reduction ratio is included. Gearbox was rebuilt by Philadelphia. 6” On center round feed throat entrance. 12.5” x 12.5” flange on feed throat.  Overall dimensions are 270” x 73” x 72”. Missing vent stack. Offered less SCR and temperature control panel.

  • Array ( [0] => extruders-3-5-10 [1] => extruders-3-5-10 )
  • Stock#: 18061

    USED NRM PACEMAKER III 3.5″ 32:1 L/D EXTRUDER


    One (1) used NRM PM III 3.5″ 32:1 L/D extruder having a five (5) zone electrically heated, air cooled, and non-vented barrel at an approximate 42″ center line height. Gearbox has a reduction ratio of 17.42:1 and is direct driven in a tuck under manner by a 75 HP Reliance D/C motor with Saftronics SCR control.. Includes integral panel having nine (9) zones of temperature controls (missing 2). Manufactured in 1973 and rebuilt 1994. Set up for c-clamp which is not included. S/N 15531. Order 103037

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => pelletizers [3] => pelletizing-lines [4] => just-arrived [5] => extruders-3-5-10 [6] => pelletizers [7] => pelletizing-lines )
  • Stock#: 18180

    USED PRODEX 4.5″ EXTRUDER / PELLETIZING LINE


    One (1) used pelletizing line with Prodex 4.5″ 32:1 L/D extruder having an electrically heated, water cooled (closed loop), and side vented barrel. The gearbox is a Lufkin change gear gearbox and driven in a tuck under manner by a 300 HP A/C motor with Yaskawa inverter. Includes stand-alone cooling system for the gearbox. Over-sized on center oblong feed throat with water cooling and volumetric screw feeder. Free-standing temperature control panel has ten (10) zones of temperature controls. Inverter is free standing and mounted in its own enclosure. Mounted on the extruder discharge is a hydraulic slide plate screen changer having two (2) nominal 4.5″ diameter breakers with hydraulic power pack, stand, and strand die. Downstream includes an 11″ Cumberland “Quietizer” pelletizer with solid helical rotor. Powered by a 25 HP A/C motor and Yaskawa model V1000 inverter. Pelletizer feeds 10″ x 72″ Witte two deck screener. Offered less extruder screw.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17954

    USED WELEX 3.5″ 30:1 L/D 150 HP EXTRUDER


    One (1) used Welex 3.5″ 30:1 L/D extruder. Electrically heated water cooled (closed loop) and vented barrel at an approximate 69″ center line height. Center line height can be reduced approximately 8″ by removing an additional base. Lufkin change gear gearbox is direct driven in a tuck under manner by a 150 HP Emerson DC motor with Control Technique Mentor II SCR control. Present reduction ratio is 13.89:1. Includes integral panel having fourteen (14) zones of temperature control. Dynisco model EH-35 screen changer with 3 HP hydraulic pack is mounted on the extruder discharge. Screen changer S/N EH-35208. Also includes 20 HP melt pump with controls. Unit was updated and the screen changer and melt pump where added 2002.  Overall dimensions are 18′ x 6′ x 103″

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17741

    PTI 4000 4″ 30:1 L/D EXTRUDER


    One (1) used 4″ 30:1 L/D ratio PTI model 4000 extruder having a five (5) zone electrically heated, water cooled (closed loop), vented, and plugged barrel at a 53″ center-line height. Flender model E2HA7 gearbox has a reduction ratio of 11.807:1 and is rated at 150 HP. The gearbox is direct driven out the back end by a 150 HP ABB motor with ABB inverter. Gearbox has an oil pump and heat exchanger. The extruder has a water-cooled feed throat with 4″ x 6″ on center entrance. The temperature control panel has five (5) zones for the barrel and fifteen( 15) zones of temperature controls for die zones. Inverter, temperature panel and 5 HP hydraulic power pack for the screen changer are mounted on the sane base as the extruder. Includes Xaloy model EH-45 hydraulic slide plate screen changer, S/N 740. Extruder S/N 4390/1069. Manufactured 2/2007. 460/3/60 input power



  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17735

    USED DAVIS STANDARD 3.5″ 34:1 L/D EXTRUDER


    One (1) Used Davis Standard model 35IN35SR 3.5″ extruder, S/N K2191. 34:1 L/D barrel having a seven zone electrically heated and water cooled (closed loop) barrel at a 56″ centerline height. Gearbox has a 5.67:1 reduction ratio and is rated at 158 HP with a service factor of 1.25. Gearbox is belt driven by a 150 HP D/C motor with Control Techniques SCR. Motor was rebuilt in December of 2018. Water cooled feed throat with 4.5″ x 7″ entrance. Integral temperature control panel has thirteen (13) zones of controls. Two instruments are missing. Manufactured 1987. 460-Volt 3-phase 60Hz input power. SO# 99878.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17744

    USED DAVIS STANDARD 3.5″ EXTRUDER W/DUAL 1.25″ CO-EXTRUDERS


    Davis Standard straw/tubing co-extrusion extrusion package manufactured 10/2012

    Last used on three color straws extruding two lanes of straws at one time. Extruders and controls are unitized on a single base. 460/3/60 input power. 278 maximum amp load

    A – Davis standard model MV35IN35 3.5” 24:1 L/D extruder having a four (4) zone electrically heated, air cooled, and non-vented barrel at a 42” centerline height. Gearbox has a 17.39:1 reduction ratio and is rated at 257 HP at a service factor of 1.25. Gearbox is belt driven by a 100 HP heavy duty A/C motor with inverter. Extruder presently set up for a maximum screw speed of 100 RPM. integral temperature control panel has ten (10) zones of Davis Standard controllers consisting of four (4) barrel, one (1) screen changer and four (4) die zones. Water cooled feed throat with a 4” x 6” entrance. Barrel is missing one heater band

    B – Mounted on the extruder discharge is an Xaloy model EHC-35 screen changer having two nominal 3.5” diameter breaker plates. S/N EH35-1056

    C – Two (2) incomplete Xaloy melt pumps with 7.5 HP A/C motors and inverters. Missing one (1) motor and one (1) gearbox. Includes free standing control panel

    D – Two (2) used Davis Standard model HPE-125A 1.25” pedestal extruders having electrically heated, air-cooled barrels. Units are height and angle adjustable. Gearbox is a SEW Eurodrive having a 15.19:1 reduction ratio. Each gearbox is direct driven by a Marathon Blue Max 2 HP heavy duty motor. Each extruder has a gravity feed hopper with Conair hopper loader

    E – Two electrically heated straw dies with two co-ex ports on each


  • Array ( [0] => extruders-3-5-10 [1] => extruders-3-5-10 )
  • Stock#: 17807

    USED EGAN 3.5″ 32:1 L/D 150 HP EXTRUDER


    One (1) used 3.5″ 32:1 L/D Egan extruder having an electrically heated, water cooled (closed loop), top vented, and plugged barrel at an approximate 52″ center line height. Philadelphia gearbox has a reduction ratio of 7:1 is and is belt driven by a 150 HP D/C motor. 3½” diameter round on center feed throat entrance. Beringer 4.5″ model 17 screen changer less hydraulic cylinder mounted on the extruder discharge. No controls. Serial number 33900 1.

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => just-arrived [3] => extruders-3-5-10 )
  • Stock#: 17694

    USED WERNER & PLEIDERER 83mm TWIN SCREW EXTRUDER


    83 mm Werner & Pfleiderer co-rotating twin screw extruder. Has 36/1 L/D barrel, driven by 200 hp dc motor with SCR control. Includes temperature control panel. No side feeder. Serial #136255.

  • Array ( [0] => extruders-3-5-10 [1] => extruders-3-5-10 )
  • Stock#: 17675

    USED DAVIS STANDARD 3.5″ EXTRUDER GEARBOX


    Davis Standard model 3.5″ Mark V extruder gearbox, 17.39:1 gear ratio, 1.25 service factor, 100 RPM output screw speed, rated for a maximum of 257 HP, S/N BE641, SO #81503, manufactured 12/2005, 2,595 Lbs. Gears are in beautiful condition

  • Array ( [0] => extruders-3-5-10 [1] => extruders-3-5-10 )
  • Stock#: 17579

    USED WELEX 3.5″ 30:1 L/D 100 HP EXTRUDER


    One (1) used 3.5″ 30:1 L/D Welex Model 350-2-1984-RHNV extruder having an electrically heated water cooled (closed loop) non-vented barrel at a 54″ center line height. Koellmann gearbox has a reduction ratio of 11.919:1 with a rating of 153 HP with a service factor of 1.0. Gearbox is driven by a 100 HP D/C motor. 5-3/8″ x 5″ feed throat entrance. S/N 2383-2-84. Manufactured in 1984. No controls.

  • Array ( [0] => extruders-3-5-10 [1] => extruders-3-5-10 )
  • Stock#: 17578

    USED HPM 3.5″ 30:1 L/D EXTRUDER


    One (1) used 3.5″30:1 HPM extruder having an electrically heated water cooled (closed loop) vented and plugged barrel at a 51 ½” centerline height. Koellmann gearbox is driven by a 100 HP D/C motor with a Eurotherm drive control. 5-3/8″ x 5″ feed throat entrance. Berringer screen changer on discharge. No hydraulic power pack or control panel.

  • Array ( [0] => used-equipment [1] => extruders-3-5-10 [2] => extrusion-roll-stacks-rolls [3] => extrusion-sheet-lines [4] => used-equipment [5] => extruders-3-5-10 [6] => extrusion-roll-stacks-rolls [7] => extrusion-sheet-lines )
  • Stock#: 16932

    USED PTI 78″ SHEET LINE


    PTI 78″ wide sheet line manufactured in 2003, last used on a PET sheet. This line consists of the following:

    One (1) PTI model 6000 6″ 36:1 L/D extruder with an eight (8) zone electrically heated water cooled (closed loop) and vented barrel at a 64″ center-line height. Gearbox is a Flender model SZNF390 with a 15.4:1 reduction ratio rated for up to 986 HP. Gearbox is directly driven by 500 HP DC motor. Offered less SCR control. No screw included. Control panel has 25 zones of Eurotherm controllers. S/N 3767/10082. Manufactured in June, 2003.

    One (1) Dynisco model EH-60 screen changer with two nominal 6″ diameter breaker plates. Includes a 2HP hydraulic power pack.

    One (1) Maag model 90/90 melt pump with 30HP drive, system controls, and model 6000 static mixer.

    One (1) Cloeren 70″ auto-flex sheet die. 1″ x 4″ back center feed entrance. S/N 77831-2129. Manufactured April, 2003.

    One (1) PTI model 7824 down stack roll stand having three rolls mounted in a vertical arrangement consisting of 24″ diameter middle and bottom chrome plated rolls and a 16″ diameter chrome plated top roll. Hydraulically actuated gapping. Rolls are driven by a 10HP AC motor through gearboxes via silent chain and sprockets. Includes temperature control system built onto frame (missing one pump), idler conveyor, dip coating station, slitting station, and pull roll stand with 78″ x 8″ diameter rolls. S/N 3354R. 480V/3ph/60Hz operation at 175 amps.

    One (1) 78″ Parkinson turret winder having four winding positions. Each station is driven by a 5HP AC motor. Includes three winding shafts. Missing gearbox on turret.


  • Array ( [0] => extruders-3-5-10 [1] => extruders-3-5-10 )
  • Stock#: 16399

    USED DAVIS STANDARD 3.5″ 30:1 L/D 200 HP EXTRUDER


    Used Davis Standard model MV35IN35SR, 3.5″ extruder, S/N K2187, SO# 99878. 30:1 L/D barrel having a seven zone electrically heated and water cooled (closed loop) and side vented barrel at a 52″ centerline height. Gearbox has a 5.67:1 reduction ratio and is rated at 158HP with a service factor of 1.25. Gearbox is belt driven by a 200HP 500V DC motor with control techniques SCR. Integral temperature control panel has ten zones of Barber Coleman controllers. Water cooled feed throat. Berringer model SL35 screen changer is mounted on the barrel discharge and includes a 3HP hydraulic power pack with hoses. Manufactured in April of 1987. 460V/3ph/60Hz input power.

  • Array ( [0] => extruders-3-5-10 [1] => extrusion-sheet-lines [2] => extruders-3-5-10 [3] => extrusion-sheet-lines )
  • Stock#: 14760

    USED WELEX 3.5″ EXTRUDER – 41″ WIDE WELEX SHEET LINE


    Welex 41″ wide sheet line consisting of:

    A) Welex model 3.5-30:1-LHSV 3.5″ 30:1 L/D extruder having an electrically heated water cooled (closed loop) barrel vented and plugged barrel at a 55″ centerline height. Lufkin change gear gearbox is direct driven in a tuck under manner by a 150HP Reliance DC motor with a Reliance SCR control. S/N 4746. Manufactured in May of 1988. Integral panel with controls. Includes two stage screw and spare screw.

    B) Berringer screen changer having two nominal 3.5″ diameter breaker plates. Includes hydraulic power pack.

    C) Welex / Maag model 56/56 melt pump with 20HP drive system. Includes co-ex block and static mixer.

    D) EDI 34″ model R-75 flexible lip sheet die having a 45 degree restrictor bar and removable lower lip. Includes die cart.

    E) 41″ Welex model 18×41-RHSL, S/N 4750, cooling and polishing stand with three 18″ (nominal) diameter chrome plated rolls mounted in a vertical arrangement for down stack operation. Air actuated chrome rolls are driven by an approximately 5HP DC motor through a gear reducer via silent chain and sprocket. Includes a stand-alone pump group with controls. Chain hoist for up and downstream movement on the sheet take-off. Used Welex 42″ wide x 6″ OD rubber / metal pull roll package driven by a 1HP motor. Includes two razor slitting blades for edge trim.

  • Array ( [0] => used-equipment [1] => extruders-3-5-10 [2] => recycling [3] => used-equipment [4] => extruders-3-5-10 [5] => recycling )
  • Stock#: 12878

    USED GLOUCESTER 233-011 3.5″ EXTRUDER


    Gloucester 3.5″, 24:1 L/D extruder model number 233-011. S/N 233-19848-01. Electrically heated air cooled vented and plugged barrel on a 42.5″ centerline. Free standing eight zone control panel with temperature controls and Reliance variable speed DC drive unit powered by a 75HP DC motor into a belt driven gearbox. Includes Berringer 3.5″ slide plate screen changer with hydraulic power unit.