Array ( [0] => blown-film-lines [1] => extruders-34-3 [2] => blown-film-lines [3] => extruders-34-3 )
  • Stock#: 18196

    USED KEIFEL 40mm EXTRUSION BLOWN FILM LINE


    A) One (1) used Keifel model CA4 40mm 24:1 L/D lowboy extruder having an electrically heated, air-cooled barrel. A second complete barrel, screw, and heaters are included to convert the machine to a 30:1 L/D ratio. Gearbox is belt driven by a 30 HP Reliance D/C motor with SCR control. Includes hopper, water cooled gearbox, grooved feed throat, and operator control panel with seven (7) zones of temperature control. Instrumentation includes controllers for (4) barrel zones, (3) die zones, blower control, speed control dial, and gauges for extruder Amps, RPM, pressure, and melt temperature. S/N 0205. Manufactured in 1989. Very clean. 460/3/60 input power.

    B) 3″ stationary blown film die less air ring. Includes 6.1 Kw air ring blower with 4 port plenum.

    C) 38″ Kiefel Model FW 811 single position surface winder for 36″ diameter rolls. Includes winder operator control panel with preset footage counter, auto fly knife, auto transfer, second pull roll assembly, and two winding shafts. S/N 0141. 460/3/60 input power. Very Clean.

  • Array ( [0] => just-arrived [1] => cast-film-lines [2] => extruders-34-3 [3] => lab-testing-equipment [4] => just-arrived [5] => cast-film-lines [6] => extruders-34-3 [7] => lab-testing-equipment )
  • Stock#: 18099

    USED COLLINS .75″ LAB CAST FILM LINE


    Used Collin laboratory blown film and cast film line. Type “Teach-Line”. Includes approximately .75″ extruder with 30:1 L/D. Extruder is equipped with melt pump, 1-3/8″ blown film die with air ring, 8″ wide nip roll mounted in tower (Serial #9550-50-06) with collapsing frame and single position winder. Extruder is electrically heated and air cooled and includes a stainless steel hopper. Also included is a 7.5″ wide 3-roll casting station, 2 of the 3 rolls are nipping and 1 is offset. Package is equipped with a single position winder and a 5″ wide adjustable lip cast film die mounted on stand. Die is Doctor Collins 160 x 70 x 80, Serial #02085200263

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 18111

    USED KILLION KN-150 1.5″ 30:1 L/D EXTRUDER


    One used Killion model KN-150 1.5″ 30:1 extruder. S/N 15437. Five (5) zone electrically heated, air cooled, and top-vented barrel at an approximate 39″ centerline height. Gearbox is a Koellmann model PEZS20 and has a reduction ratio of 11.2:1 and is rated at 16 HP at a service factor of 1.0. Gearbox is belt driven by a 15 HP D/C motor with SCR control. Unitized temperature control pane has eight (8) zones of temperature controllers. Caster mounted. Strand die on discharge. 460/3/60 input. 56 maximum amp load. Reconditioned in 2014

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 18060

    USED NRM PACEMAKER III 24:1 L/D 2.5″ EXTRUDER


    One (1) Used 2.5″ NRM PM III extruder having a 24:1 L/D four (4) zone electrically heated, air cooled, and non-vented barrel at approximately a 42″ center line height. Gearbox has a reduction ratio of 15:1 and is belt driven by a 40 HP Reliance 500-volt D/C motor with Flex-Pak SCR control. Gearbox is rated at 40 HP at a service factor of 1.25. Unitized control panel has seven (7) zones of temperature controls. Manufactured 1993. 460/3/60. 95 FLA. S/N 19255. Order 54326

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17759

    USED 2.5″ 30:1 L/D EXTRUDER


    Unknown manufacture 2.5″ extruder, 30:1 L/D air cooled non-vented barrel at a 23.5″ centerline. Powered by a 40 HP 230/460-volt A/C motor with Teco A510 inverter. 4″ x 6″ feed throat. Unitized control panel with four (4) temperature controllers

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17906

    USED KILLION KLB075 3/4″ EXTRUDER


    One (1) Used Killion model KLB-075 3/4″ 32:1 extruder having four (4) zones electrically heated and air cooled. Non-vented barrel at approximately a 38″ center-line height. Gearbox is belt driven by a 1.5 HP brush-less D/C motor. Caster mounted temperature control panel has seven (7) zones of controllers consisting of four (4) zones for the barrel and three (3) zones for the downstream. Mounted on the same portable cart is a melt pump with 1 HP drive mounted on the extruder discharge. 208/3/60. 14.3 KVA. Serial number 18442.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17805

    USED GLOUCESTER 2522 2.5″ 32:1 L/D EXTRUDER


    One (1) Used Gloucester model 2522 R2 2.5″ 32:1 L/D extruder with an electrically heated, water cooled (closed loop) vented and plugged barrel at approximately a 72″ center line height. Gearbox has a reduction ratio of 10.73:1 and is direct driven by a 60 HP D/C motor with Saftronics SCR control. Manual screen changer mounted on the extruder discharge. Includes panel with controls. Rebuilt by Gloucester approximately in 2000. S/N 36858-01.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17885

    USED WAYNE MFG 3/4″ EXTRUDER


    One used 3/4″ 20:1 L/D Wayne laboratory extruder having a two (2) zone electrically heated, air cooled barrel. Gearbox is belt driven by a 2 HP DC Motor with controls. Unitized temperature control panel with three (3) zones of temperature control. Mounted on a cart which raises the unit 36 ½” from the floor. No screw included. 230/3/60 30 amps. S/N 5274

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17690

    USED GLOUCESTER 2.5″ 32:1 L/D EXTRUDER


    Gloucester 2.5″ extruder, 32:1 L/D five (5) zone air cooled and vented barrel at a 45″ centerline height. Top center feed throat. Driven by a 50 HP A/C 1750/2100 RPM motor, includes 6 zone temperature control panel and 5 hole strand die

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17708

    USED DAVIS STANDARD 150IN 1.5″ 24:1 L/D EXTRUDER


    Davis Standard model 150IN DS-20 1.5″ extruder, S/N J6173, 1984 model year, 24:1 L/D vented barrel at a 42″ centerline. Davis Standard 6.53:1 gearbox rated for 50 HP with a service factor of 1.25 for a 152 RPM screw speed. Gearbox was manufactured in 1998. Non-tagged motor is driven by a Reliance model GV3000 A/C drive. Includes unitized temperature control panel and 4-hole strand die on barrel

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 17654

    USED EGAN 2″ 24:1 L/D 25 HP EXTRUDER


    One (1) Used 2″ 24’1 Egan extruder having a five (5) zones electrically heated, air cooled, and non-vented barrel at approximately a 50″ centerline height. Extruder is mounted on a mobile cart with casters. If the extruder is removed from the cart it will have a nominal 42″ centerline height. Cone Drive gearbox has a reduction ratio of 10:1 and is rated at 19 HP at a service factor of 1.0. Gearbox is belt driven by a 25 HP D/C motor with an Allen-Bradley model 1395 drive. Unitized temperature control panel has fifteen (15) zones of controllers. C clamp on the barrel discharge. Gravity feed hopper with Conair DB 8 hopper loader on the feed throat. Feed throat entrance is nominal 3″ round. Machine recently updated. Serial number JO 07319-05. 240/3/60 input on the barrel. 460/3/60 on the drive. Several transformers included. Extremely clean. Ideal co-extruder. Approximately 6,000 Lbs.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17542

    USED DAVIS STANDARD 1.5″ 34:1 L/D EXTRUDER


    one (1) used Davis Standard model Thermatic 150 1.5″ extruder, S/N 62570, 34:1 L/D barrel having a five (5) zone electrically heated, air cooled, and non-vented barrel at approximately a 42? centerline height. Gearbox has a reduction ratio of 11.31:1 and is rated at 18 HP at a service factor of 1.5. gearbox is belt driven by a 15 HP D/C motor with isolation transformer and Reliance SCR control. Unitized temperature control panel has eight zones of controllers consisting of five (5) zones for the barrel and three (3) zones for the die. S/O 9077. C-clamp on discharge. 460/3/60 input power. Includes spare cast aluminum barrel heater and screen packs

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17529

    USED KILLION KN-150 1.5″ 24:1 L/D EXTRUDER


    One (1) Used Killion model KN-150 1.5″ extruder. 24:1 L/D barrel having four (4) zones electrically heated, air cooled, and non-vented barrel at approximately a 39? centerline height. Koellmann model PEZS20 gearbox has a reduction ratio of 11.2:1 and is rated at 16 hp at a service factor of 1.0. Gearbox is belt driven by a 15 HP D/C motor with Emerson Mentor II SCR control. Unitized temperature control panel has seven (7) zones of controllers consisting of four zones for the barrel and three (3) zones for the downstream. Swing away die holder with adapter on the discharge. very clean. 230/3/50-60 input

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17576

    USED WELEX 2″ 24:1 L/D CO-EXTRUDER (NO MOTOR)


    One (1) used 2″ 24:1 L/D Welex co-extruder. Water cooled. Missing motor, drive panel, and pedestal. Last used on a sheet line.

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 17504

    USED DAVIS STANDARD 1.5″ 20:1 L/D RUBBER EXTRUDER


    One (1) used 1.5″ 20:1 L/D ratio Davis Standard rubber extruder with powered feed roll on throat. Barrel is electrically heated, water cooled (closed loop) and vented at approximately a 42″ centerline height. Includes oil style vacuum pump. C-clamp with die on barrel discharge. Oversize gearbox has a reduction ratio of 17.56:1 and is rated at 50 HP at a service factor of 1.25:1. Gearbox is belt driven by a Marathon Blue Max 25 HP A/C motor with Allen Bradley Power Flex 753 inverter with isolation transformer. Unitized temperature control panel has seven (7) zones of temperature controls. Manufactured January of 2001. Model 150IN20. Shop order number 71118. S/N 16633. 460/3/60 input. 77 FLA.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 17438

    USED WELEX 2″ 24:1 L/D EXTRUDER


    Welex model 200-24/1, 2″ 24:1 L/D extruder with a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 50″ centerline height. Gearbox is a Koellmann Gear and is belt driven by a 20 HP D/C motor with SCR control. D/C motor was recently replaced. Unitized temperature control panel with six (6) zones of controllers consisting of three zones for the barrel and three die zones. Swing gate on discharge. Gravity feed hopper. S/N 2235 3-83. 460V/3ph/60Hz input. Includes the documentation manual.

  • Array ( [0] => just-arrived [1] => extruders-34-3 [2] => just-arrived [3] => extruders-34-3 )
  • Stock#: 17437

    USED DAVIS STANDARD 1/4″ TUBING EXTRUSION LINE


    Davis Standard 1/4″ tubing extrusion line including the following equipment:

    A. Davis Standard / Killion model KN-100 1.00″ 24:1 L/D extruder having a three (3) zone electrically heated, air cooled non-vented barrel at approximately a 39″ centerline height. Gearbox is belt driven by a 3 HP D/C motor with SCR control. Unitized temperature control panel has six (6) zones of Eurotherm controllers consisting of three (3) zones for the barrel and three (3) zones for the c-clamp and die. C-clamp is mounted on the discharge. Includes gravity feed hopper. BOM number 05180. 230V/1ph/50-60Hz input, 47 FLA.

    B. Nominal ¼” diameter electrically heated tubing die.

    C. Davis Standard / Killion medical tubing vacuum tank measuring 116″ long with an 8″ x 8″ cross section. Stainless steel construction. Two glass doors. Upstream and downstream adjustment as well as up and down adjustment. Includes vacuum pump with 3 HP D/C motor, water pumps, sizing fixture, and controls. S/N 30176. 230V/1ph/60Hz input.

    D. Davis Standard / Killion belt puller having a 2″ wide belt with 22″ of contact length. Powered by an approximate 1.5 HP D/C motor. Manually actuated top belt. S/N 30174. 230V/3ph/60Hz input, 10 FLA.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 16305

    USED KILLION 1″ 24:1 L/D EXTRUDER


    24:1 Killion pedestal extruder. S/N N6598 with a three (3) zone electrically heated air cooled barrel. Gearbox has a reduction ratio of 30:1 and is direct driven by a 3HP 1750/2050 RPM DC motor. Barrel can be raised or lowered and also tilts for co-extrusion applications. Integral temperature control panel has four zones of Eurotherm temperature controllers. Pressure gauge on discharge. Mounted on casters.

  • Array ( [0] => used-equipment [1] => extruders-34-3 [2] => used-equipment [3] => extruders-34-3 )
  • Stock#: 14768

    BELLAFORM MODEL BH25-25D 25mm EXTRUDER


    Bellaform co-extrusion package consisting of the following:

    Bellaform model BH25-25D 25mm extruder. S/N P19-330877, 10.5 kW AC motor with tachometer and drive, 220-Volt operation. 25:1 L/D air cooled barrel with 3 heating and cooling zones. Has 3 kW heating capacity and a 155 RPM screw speed, and a 43″ centerline. Includes the control panel. Bellaform model BH45-25D 45mm extruder S/N P19-330875 31 kW AC motor with tachometer and drive 220-Volt operation. 25:1 L/D air cooled barrel with 3 heating and cooling zones and a 6.5 kW heating capacity, 227 RPM screw speed and a 43″ centerline. Includes the control panel. Six (6) station model 2200 Plasticolor additive feeding system, S/N 10011. Includes 6 Schmidt & John 1.5″ inlet vacuum loaders controls for feeder. Loaders are in the extruder control panels. All items were manufactured in 2000.

    Two complete systems are available.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 16607

    USED DAVIS STANDARD DS-125 1.250″ 24:1 L/D EXTRUDER


    Davis Standard model DS-125 pedestal extruder, S/N K-3031. 24:1 L/D electrically heated 3 zone air cooled barrel with adjustable height and angle. Pedestal mounted stand alone control panel. 15:1 gearbox ratio. 7HP maximum capacity motor with a 1.25 service factor.