-
Stock#: 18419
USED LUFKIN TYPE 45 4.5″ EXTRUDER GEARBOX ONLY
One (1) used Lufkin / Welex change gear style gearbox last used on a 4.5″ Welex extruder. Presently installed gears give a reduction ratio of 17.55 to 1 and is rated at 319 HP. Set up for tuck under, direct drive. Includes shaft mounted Tuthill lubrication pump with heat exchanger. Integral thrust bearing. Weighs approximately 5500 pounds.
-
Stock#: 18280
USED 60mm LEISTRITZ EXTRUDER SIDE FEEDER
Used 60mm Leistritz twin screw side feeder. Includes new spare gear reducer.
-
Stock#: 18279
USED 70mm LEISTRITZ EXTRUDER SIDE FEEDER
Used 70mm Leistritz twin screw side feeder Model LSB70. Order No. 310.11004.01. Machine No. 4080. New 2011.
-
Stock#: 17045
USED CO-EX IN-FEED BLOCK
Used co-ex infeed block, 3″ OD sheet die hole, 1.5″ OD die hole size.
-
Stock#: 18229
USED GLOUCESTER SHEET STACKER
One (1) used Gloucester cut sheet stacking system. Package consists of a nominal 72″ wide x 9′ long belt conveyor with 72″ wide pneumatic sheet stacker. Last used on the end of an HDPE sheet extrusion line. ¾ hp motor on the conveyor. Gloucester serial number 25109-01.
-
Stock#: 18091
USED 8 ZONE EXTRUDER CONTROL CONSOLE
One (1) used eight (8) zone console type control panel. Last used with a Berstorff single screw extruder.
-
Stock#: 18038
USED LINK BELT 17:1 GEARBOX FOR HARTIG EXTRUDER
Link Belt model 60-HL-60 Hartig extruder gearbox. 17:1 gear ratio. 1150 input RPM. Rated for 150 HP with a service factor of 1.25. Does not have integral thrust section.
-
Stock#: 17862
USED BROWN 56″ WIDE SHEET CUTTER
Used 56″ wide Brown sheet cutter. S/N 33171. New 2005. Has gear-head score cut cross cut slitting blade and manually adjusted blade carriage.
-
Stock#: 17790
USED CMS CB61224 COOLING BELT
One (1) used CMS model CB61224 cooling belt measuring 23 ½” wide x nominal 61″ long. Two spring loaded chrome rolls with rotary unions feed the stainless steel cooling belt. Discharge has a pin bat for breaking up the cooled product. Last used on powder coating. Includes controls. Serial number 4782. 575 volts.
-
Stock#: 17812
USED COROTEC CPT-20 CORONA TREATER
One (1) used Corotec model CR104-PE 56″ wide corona treater. S/N T-15974-04-10. Unit has individual sliding fingers that adjust up to a 50″ wide treater width. With 2 Kw high voltage transformer and model CPT-20 controls. Job number T-15974. 240/1/60 input. Rated at 120 FPM
-
Stock#: 17813
USED LOT OF 2.5″ & 3.5″ STATIC MIXERS
One (1) lot of transfer piping and static mixers, one 2.5″ and one 3.5″
-
Stock#: 17719
USED BRABENDER PL2100 PLASTICORDER RHEOMETER SYSTEM
Used Brabender Model PL2100 plasticorder rheometer system. Drive type DR-2072/PE. 7.5 HP. Model Poly Speed 04440/PE. Includes controls, temperature control panel and a 1.25” 24:1 L/D extrusion head with stand, die and feeder. 230/3/60 input. Rheometer is mounted on a cart.
-
Stock#: 17716
USED BRABENDER PL2000 PLASTICORD RHEOMETER
Used Brabender Model PL2000 Plasticord rheometer. Drive type DR-2072-L63. 7.5 HP. Model Poly Speed 0220/PE . Includes six (6) temperature control panel and operator controls. S/N 409
-
Stock#: 17715
USED BF PERKINS 2 ROLL CALENDAR ROLL MILL
One(1) used B.F. Perkins laboratory two roll calendar having two(2) 13″ face x nominal 10″ diameter rolls mounted in a vertical arrangement. One roll is rubber covered while the other is chrome plated. Rolls are variable speed and electrically heated. With controls. Very clean. Serial number H-7642-88.
-
Stock#: 17243
USED 14″ 3 LAYER BLOWN FILM DIE
One (1) used 14″ three layer blown film die package mounted on a rotating die cart. Last used with one (1) 3.5″ and two (2) 2.5″ extruders. Includes melt pipes adapters and dual lip air ring. 0.090″ die gap, 13.822″ diameter die.
-
Stock#: 16936
USED JOHNSON 8″ X 30 TWO ROLL PULL ROLL STAND
Johnson two roll pull roll stand driven by a “Drive-All” 3HP DC motor and gearbox. Pull rolls operate at 1.0, 2.07, 5.058, and 10.651:1 ratios. Pull rolls are 8″ diameter x 30″ wide and have not been used since recovering pull rolls have pneumatic pinch. Includes air accumulation tank.
-
Stock#: 16351
USED KAYNESS D5052M-115 CAPILLARY RHEOMETER
Kayness model D5052M-115 capillary rheometer, S/N 9712-469. 110-Volt operation, 10 amps maximum. Includes rheometer microscope, Exacal high temperature bath, lot of miscellaneous parts and testing accessories and a 3-drawer test bench with hydraulic pump station.
-
Stock#: 18238
USED DAVIS STANDARD 6″ EXTRUDER GEARBOX ONLY
One (1) used Davis Standard model 60IN60TPIH extruder gearbox. 17.21:1 gear ratio. Rated at 526 HP at a service factor of 1.5. S/N 06890. S/O 6890. Manufactured 6/21/1999. Gears are in beautiful condition. With heat exchanger.
-
Stock#: 16282
USED TUTHILL LIQUID RING VACUUM PUMP
Tuthill vacuum systems liquid ring vacuum pump, S/N 240745, 3HP 208-230/460-Volt motor, wire for 230V operation with starter. Kinney high vacuum pump model 4020-3T3-B-V, manufactured in 2010.
-
Stock#: 16190
USED 4″ CROSS-HEAD DIE
One 4″ cross head die previously used on a 6″ extruder die. Unit is electrically heated and currently mounted on adjustable base. It includes a 6″ extruder adapter.