Array ( [0] => just-arrived [1] => extrusion-roll-stacks-rolls [2] => just-arrived [3] => extrusion-roll-stacks-rolls )
  • Stock#: 18352

    USED GLOUCESTER COOLING ROLL STACK


    One (1) used Gloucester heavy duty cooling and polishing stand having three (3) 55″ face x 24″ diameter chrome plated rolls mounted in a 45-degree angle arrangement for down stack operation at a 62″ center line height. Serial number 36736-33. Chrome rolls are hydraulically actuated via a nominal 7.5 HP hydraulic unit. Manual roll gaping via hand wheels. Rolls are each individually driven by an A/C inverter duty motor through a gearbox having a 15:1 reduction ratio via silent chain and sprocket. Top roll has a 7.5 HP A/C motor, middle roll has a 5 HP A/C motor and the bottom roll has a 3 HP A/C motor. Includes pull roll stand with 55″ x 8″ diameter rolls and a 3 A/C HP drive system, idler roll conveyor and built onto frame zone water temperature control system with heaters, heat exchangers, and one (1) 10 HP and three (3) 7.5 HP water pumps. Complete with all new electrical cabinets and controls. 460V/3ph/60Hz. Includes five (5) chrome rolls and one (1) matte finish roll in boxes. Rebuilt 2011 and never put into service.

  • Array ( [0] => extrusion-roll-stacks-rolls [1] => extrusion-roll-stacks-rolls )
  • Stock#: 17852

    USED DAVIS STANDARD 62″ X 12″ 3 ROLL STACK


    One (1) Used 64″ wide Davis Standard 3 roll chill roll stack. 64″ x 12″ chrome rolls with rotary unions driven by a 3 HP gear motor. Includes 64″ wide rubber pull roll assembly. No cooling conveyor and NDC gauge shown in photos is not included.

  • Array ( [0] => just-arrived [1] => extrusion-roll-stacks-rolls [2] => just-arrived [3] => extrusion-roll-stacks-rolls )
  • Stock#: 18226

    USED GLOUCESTER 66″ COOLING ROLL STAND


    One (1) used 66″ Gloucester cooling and polishing stand having three (3) nominal 20″ diameter chrome plated rolls mounted in a vertical arrangement for down stack operation at a 56″ center-line height. Includes two additional chrome rolls for additional cooling. Rolls are hydraulically actuated via 3 HP hydraulic pump. Chrome rolls are driven by via silent chain and sprockets via a 3 HP A/C motor through a four speed gear reducer. Includes 66″ pull roll stand with 4 speed transmission and 3 HP drive system. Includes idler conveyor and inline slitting provision One chrome roll replaced last year at a cost of $30,000. Pulled from service due to plant closure 12/ 2022. S/N 24148-16. 460/3/60. Manufactured 3-8-80. Unit has been continuously updated.

  • Array ( [0] => extrusion-roll-stacks-rolls [1] => extrusion-roll-stacks-rolls )
  • Stock#: 18013

    USED 60″ S-WRAP ROLL STAND


    60″ wide S-wrap roll stand. Silent chain drive powered by a 2 HP 1750/2050 RPM 180-volt D/C motor. Pneumatic pressure rolls

  • Array ( [0] => just-arrived [1] => extrusion-roll-stacks-rolls [2] => just-arrived [3] => extrusion-roll-stacks-rolls )
  • Stock#: 18040

    USED PTI 3 ROLL DOWNSTACK W/COOLING SYSTEM


    One (1) used PTI model Revolution cooling and polishing stand with three 66″ face chrome plated rolls mounted in a vertical arrangement for down stack operation. The top roll measures nominal 15″ diameter, while the middle and bottom rolls measure nominal 18″ diameter. Top roll has a matte finish while that middle and bottom rolls are chrome. Chrome rolls are hydraulically actuated. No hydraulic unit. Roll gapping via .5 HP SEW servo motor. Rolls are each driven by a 4 KW (5.3 HP) inverter duty motor with encoder through a gearbox. Stand-alone three zone water temperature control system with heaters and heat exchangers, 7.5 KW (10 HP) water pumps and integral electrical cabinet with pendulum operator control. Includes four (4) spare 66” x 18” Chrome rolls and one 66” x 15″ chrome roll. Spare rolls appear to be either new or unused. Model R661518. S/N 4623/1108. Last used on PET. Cooling and polishing stand weighs approximately 20,000 and the temperature system is approximately 6,000 pounds.

  • Array ( [0] => extrusion-roll-stacks-rolls [1] => extrusion-roll-stacks-rolls )
  • Stock#: 17811

    USED GLOUCESTER 60″ COOLING AND POLISHING STAND


    One (1) used 60″ Gloucester model 2000SLA cooling and polishing stand having three (3) nominal 24″ diameter chrome plated rolls mounted in a 45-degree arrangement for down stack operation. Rolls are pneumatically actuated. Chrome rolls are driven by an approximate 5 HP A/C motor through a gear reducer. Includes 60″ pull roll stand with approximate 5 HP A/C drive system with idler conveyor built onto frame. Includes (3) three zone water temperature control system with heaters, heat exchangers, and pumps. Unitized controls. S/N 40371-02. Manufactured 6/1999.

  • Array ( [0] => extrusion-roll-stacks-rolls [1] => extrusion-roll-stacks-rolls )
  • Stock#: 17581

    USED DAVIS STANDARD 24″ X 48″ 3 ROLL DOWN-STACK


    One (1) used 48″ Davis Standard cooling and polishing stand having three (3) nominal 24″ diameter chrome plated rolls mounted in a vertical arrangement for down stack operation. Rolls are pneumatically actuated. Chrome rolls are driven by via silent chain and sprockets via a 5 HP D/C motor through a gear reducer. Includes 48″ pull roll stand with 5 HP drive system, 10′ idler conveyor built onto frame, includes three zone water temperature control system with heaters, heat exchangers, and pumps. Model 28751. S/O 01624C, S/N K 7293. Manufactured 9-23-1988.

  • Array ( [0] => extrusion-miscellaneous [1] => extrusion-roll-stacks-rolls [2] => extrusion-miscellaneous [3] => extrusion-roll-stacks-rolls )
  • Stock#: 16936

    USED JOHNSON 8″ X 30 TWO ROLL PULL ROLL STAND


    Johnson two roll pull roll stand driven by a “Drive-All” 3HP DC motor and gearbox. Pull rolls operate at 1.0, 2.07, 5.058, and 10.651:1 ratios. Pull rolls are 8″ diameter x 30″ wide and have not been used since recovering pull rolls have pneumatic pinch. Includes air accumulation tank.

  • Array ( [0] => extrusion-roll-stacks-rolls [1] => extrusion-roll-stacks-rolls )
  • Stock#: 14917

    USED DAVIS STANDARD 52″ WIDE 3 ROLL STACK


    Davis standard model Exemplar cooling and polishing stand with three 52″ face chrome plated rolls mounted in a vertical arrangement for down stack operation. The top roll measures a nominal 18″ in diameter, while the middle and bottom rolls measure nominal 30″ in diameter. Chrome rolls are hydraulically actuated via a 7.5HP hydraulic unit. Roll gapping via servo motor with control. Rolls are driven by a 10HP inverter duty motor with encoder through a gearbox via a silent chain and sprocket. Includes pull roll stand with 52″ x 8″ diameter rolls and a 5HP drive system idler roll conveyor and stand-alone three zone water temperature control system with heaters, heat exchangers, and one (1) 10HP and two (2) 7.5HP water pumps. Last used in line with a thermoformer. Complete with integral electrical cabinets and pendulum operator controls with AB Panelview 550 touch screen. 460V/3ph/60Hz operation. 142 amps.


  • Array ( [0] => used-equipment [1] => extruders-3-5-10 [2] => extrusion-roll-stacks-rolls [3] => extrusion-sheet-lines [4] => used-equipment [5] => extruders-3-5-10 [6] => extrusion-roll-stacks-rolls [7] => extrusion-sheet-lines )
  • Stock#: 16932

    USED PTI 78″ SHEET LINE


    PTI 78″ wide sheet line manufactured in 2003, last used on a PET sheet. This line consists of the following:

    One (1) PTI model 6000 6″ 36:1 L/D extruder with an eight (8) zone electrically heated water cooled (closed loop) and vented barrel at a 64″ center-line height. Gearbox is a Flender model SZNF390 with a 15.4:1 reduction ratio rated for up to 986 HP. Gearbox is directly driven by 500 HP DC motor. Offered less SCR control. No screw included. Control panel has 25 zones of Eurotherm controllers. S/N 3767/10082. Manufactured in June, 2003.

    One (1) Dynisco model EH-60 screen changer with two nominal 6″ diameter breaker plates. Includes a 2HP hydraulic power pack.

    One (1) Maag model 90/90 melt pump with 30HP drive, system controls, and model 6000 static mixer.

    One (1) Cloeren 70″ auto-flex sheet die. 1″ x 4″ back center feed entrance. S/N 77831-2129. Manufactured April, 2003.

    One (1) PTI model 7824 down stack roll stand having three rolls mounted in a vertical arrangement consisting of 24″ diameter middle and bottom chrome plated rolls and a 16″ diameter chrome plated top roll. Hydraulically actuated gapping. Rolls are driven by a 10HP AC motor through gearboxes via silent chain and sprockets. Includes temperature control system built onto frame (missing one pump), idler conveyor, dip coating station, slitting station, and pull roll stand with 78″ x 8″ diameter rolls. S/N 3354R. 480V/3ph/60Hz operation at 175 amps.

    One (1) 78″ Parkinson turret winder having four winding positions. Each station is driven by a 5HP AC motor. Includes three winding shafts. Missing gearbox on turret.


  • Array ( [0] => extrusion-roll-stacks-rolls [1] => extrusion-roll-stacks-rolls )
  • Stock#: 16359

    USED WAYNE 8″ X 5″ HORIZONTAL ROLL STACK


    Wayne horizontal roll stack, S/N 9545. Five (5) 8″ wide x 5″ diameter rolls. Three (3) chrome and two (2) rubber. Each roll has a rotary union for cooling. Powered by two gearhead motors. Operator controls and one spare rubber roll are included.

  • Array ( [0] => extrusion-roll-stacks-rolls [1] => extrusion-roll-stacks-rolls )
  • Stock#: 16019

    CHROME ROLL 10″ X 36″


    10″ diameter x 36″ chrome roll cored for water cooling.

    Two are available.

  • Array ( [0] => used-equipment [1] => extrusion-roll-stacks-rolls [2] => used-equipment [3] => extrusion-roll-stacks-rolls )
  • Stock#: 6522

    USED PROCESSING TECHNOLOGIES 50″ WIDE 3 ROLL DOWN STACK


    Processing Technologies, Inc. model 5024, 3 roll down stack. S/N 297-CRS. Manufactured in February, 2000. Has two (2) 24″ diameter x 50″ wide lower chrome rolls. Upper roll is 12″ x 50″. All chrome rolls are cored for cooling. Rolls are hydraulically operated and powered by a 7.5HP DC motor via a silent chain drive. Control Techniques Mentor II DC drives for stack and pull roll station. Pull rolls are pneumatically operated and powered by a 5HP DC motor. Cooling via 3 x 10HP pumps into heat exchangers.

  • Array ( [0] => used-equipment [1] => extrusion-roll-stacks-rolls [2] => used-equipment [3] => extrusion-roll-stacks-rolls )
  • Stock#: 6547

    USED CINCINNATI MILICRON (WELEX) 2 ROLL STACK / LAMINATOR


    Cincinatti Milicron 2 roll stack / laminator, no S/N. Two (2) chrome rolls 17.75″ diameter 34″ wide cored for cooling. Two (2) aluminum guide rolls. One (1) is 17.75″ diameter x 31″ wide, and one (1) is 8″ diameter x 31″ wide. Chrome rolls are pneumatically operated and are powered by a 5HP 1,750 RPM 500-Volt DC motor through a Koellmann 18.131:1 gearbox via a silent chain drive. Rolls are cooled via three 5HP pumps. Heat exchanger pull roll station has two (2) rubber coated steel rolls at 17.75″ diameter x 34″ wide, and one at 8″ diameter x 34″ wide, pneumatically operated and driven by the same drive system as the roll stack. Includes unwinder station with an approximately 40″ diameter package, dual tension controls, foot pedal actuated. No DC drives or controls for any. Items are all set for a 42″ centerline.

  • Array ( [0] => used-equipment [1] => extrusion-roll-stacks-rolls [2] => used-equipment [3] => extrusion-roll-stacks-rolls )
  • Stock#: 3790

    USED TEXTURED ROLL 53″ X 18″ DIAMETER


    Textured roll 18″ diameter x 53″ long with textured surface.

  • Array ( [0] => used-equipment [1] => extrusion-roll-stacks-rolls [2] => used-equipment [3] => extrusion-roll-stacks-rolls )
  • Stock#: 3384

    CHROME ROLL 80″ X 16″ DIAMETER


    Chrome roll 16″ diameter x 80″ long.

  • Array ( [0] => used-equipment [1] => extrusion-roll-stacks-rolls [2] => used-equipment [3] => extrusion-roll-stacks-rolls )
  • Stock#: 3792

    CHROME ROLL 53″ X 18″ DIAMETER


    Chrome rolls 18″ diameter x 53″ long.

  • Array ( [0] => used-equipment [1] => extrusion-roll-stacks-rolls [2] => used-equipment [3] => extrusion-roll-stacks-rolls )
  • Stock#: 4941

    TEXTURED ROLL


    Textured roll, cored for cooling, 12″ diameter x 54″ wide.

  • Array ( [0] => used-equipment [1] => extrusion-roll-stacks-rolls [2] => used-equipment [3] => extrusion-roll-stacks-rolls )
  • Stock#: 4942

    TEXTURED ROLL


    Textured roll, cored for cooling, 12″ diameter x 53″ wide.