-
Stock#: 18254
USED EDI R75 16″ SHEET DIE
Extrusion Dies Inc. model R75 16″ sheet die. S/N 86-10534. Back center feed. 45 degree restricting bar. Integral upper flexible lip and removable lower lip. Three (3) electrical heat zones. Adjusting bolts on 1″ centers. Includes two (2) .001-.300″ spare lower lips. Manufactured in 1986
-
Stock#: 17961
USED 40″ FLEX LIP SHEET DIE
Used 40″ wide flex lip sheet extrusion die with end feed. Previously used for sheet extrusion of thermoformed hot/cold drinking cup lids
-
Stock#: 18225
USED NORDSON / EDI 66″ SHEET DIE
One (1) used Nordson / Extrusion Dies Inc. heavy duty sheet die. S/N 302600006. Has a 66″ slot opening with five (5) zones of temperature control. Upper sliding lip is adjustable. Fixed removable lower lip. Vertical restriction bar. 1.5″ square back center feed entrance. Integral deckling attachments. Includes die cart allowing for a 56″ center-line height with height adjustment. Last ran nominal .250 thick HDPE sheet. Appears to have an additional .250 of adjustment.
-
Stock#: 18202
USED EDI 8″ SHEET DIE
One (1) used Extrusion Dies Inc. model Ultra-flex R75 sheet die having an 8″ slot opening. Integral upper flexible lip and removable lower lip. 45 degree restriction bar. Adjusting bolts on 1″ centers. 1″ back center feed. Manufactured in 1986. Lab use. .000-.075. 230/1/60. S/N 86-10636
-
Stock#: 18184
USED 6″ ETTI FLEXIBLE LIP SHEET DIE
One (1) Used 6″ ETTI flexible lip sheet extrusion die. Job 6855. Has center back input supplying approximately 45-degree downward angle extrusion
-
Stock#: 18011
USED CLOEREN 46″ HD-100 SHEET DIE
Cloeren model HD-100 46″ sheet die. S/N 04-7722. 1.5″ diameter back center material entry. 13.3 Kw. 1258 Lbs. Manufactured 03/2004
-
Stock#: 18012
USED EDI 38″ ULTRAFLEX H75 SHEET DIE
Extrusion Dies Inc. model Ultraflex H75 38″ sheet die. S/N 87-11441-1. 1-1/8″ diameter back center material entry. 480/1/60 heaters. No restrictor bar
-
Stock#: 17968
USED EDI 96″ SHEET DIE
One (1) used sheet die believed to have been manufactured by Extrusion Dies Inc. Having a 96″ slot opening. Integral upper flexible lip and removable lower lip. Vertical restriction bar. Adjusting bolts on 1″ centers. 1 ½” back center feed. S/N 80-3915. Installed lip range is .001-.315. Spare lip range .315-.565. Missing end plates, restriction bar hardware, and all electricals. Weighs approximately 5,000 pounds
-
Stock#: 17966
USED EDI HRC300 90″ SHEET DIE
One( 1) used Extrusion Dies Inc. model Ultra-flex HRC 300 sheet die with Fast Gap having a 90″ slot opening. Integral upper flexible lip is adjustable, removable lower lip. 45 degree restriction bar. Adjusting bolts on 1″ centers. .300 gap .adjustment. Coat-hanger manifold. 1 ½” back center feed. Fast gap needs repair, but die can be used without the fast gap. Manufactured in 1995. S/N 95-17703. Weighs 4236 pounds.
-
Stock#: 17967
USED EDI ULTRA-FLEX R75 90″ SHEET DIE
One (1) used Extrusion Dies Inc. model Ultra-flex R75 sheet die. S/N 79-3368-3. having a 90″ slot opening. Integral upper flexible lip and removable lower lip. 45 degree restriction bar. Adjusting bolts on 1″ centers.. 1 ½” back center feed. Manufactured in 1979. Includes spare lower lip.
-
Stock#: 17045
USED CO-EX IN-FEED BLOCK
Used co-ex infeed block, 3″ OD sheet die hole, 1.5″ OD die hole size.
-
Stock#: 12063
USED MASTERFLEX 5″ HD SHEET DIE
Masterflex 5″ HD extrusion sheet die. Job 2905-94. 1.5″ OD material entry port. Six 500 watt, 240 volt heater cartridges. 240/1/60 operation. Hard chrome plated flow surfaces. 0.188″ (+/- 0.002″) lip opening. Manufactured by Production Components in August, 1994.
-
Stock#: 16747
USED 9″ EDI CAST FILM DIE
EDI Ultraflex H40 9″ cast film die. S/N 11-30324. 354 lbs. (die only). 0.130″ lip opening with a 1.250″ land six 480-Volt heater zones @ 800 watts each. 1.000″ diameter bottom center feed all flow surfaces are chromed. Includes die stand. Designed to operate in vertical position.
-
Stock#: 17439
USED CLOEREN HD-75 9″ SHEET DIE
Cloeren / Production Components model HD-75 9″ sheet die. Integral upper flexible lip and removable lower lip. Adjusting bolts on 1″ centers. Flex adjustment of 0.075″. Coat hanger manifold. Job number 0093-86. last ran dental products on a 2″ Welex extruder. Includes die cart.
-
Stock#: 10872
USED CLOEREN 12″, 3 LAYER VANE DIE
Cloeren 12″ 3 layer vane die, S/N D.ND935-0103-01, job no. 91-935, mounted on a caster stand, three 1.5″ material entries on a Cloeren 3 layer co-ex block (a b c), job no. D-935-2001-01, S/N E-3lSP-1636, 0.001″ to 0.040″ lip opening, flame hardened die lip lands, 11 – 240V/1ph/60Hz heater zones powered by a stand alone 11 zone control panel and power supply using Eurotherm instruments digital controllers. Panel is also mounted on casters.
-
Stock#: 10322
USED PRODUCTION COMPONENTS 20″ PVC SIDING DIE
Production Components 20″ PVC siding die, S/N 6237-00, 20″ dual manifold, 2″ OD rear PVC material entry, side acrylic material entry, 0.020″ – 0.060″ adjustable lip opening, 9 heating zones. 240V/1ph/60Hz operation. Rebuilt by Allied Dies, Inc. in May 2005, Allied S/N AD-1716-01.
-
Stock#: 2939
USED EDI MODEL 3940221 24″ SHEET DIE
Extrusion Dies, Inc. 24″ sheet die mold: 3940221 S/N: 86-10048 Autoflex H40 24″, 240-Volts.
-
Stock#: 6671
USED EDI 28.5″ ULTRAFLEX H40 SHEET DIE
Extrusion Dies, Inc. 28.5″ Ultraflex H40 sheet die. S/N 89-12354. 0.001″ – 0.040″ lip opening 240 volt 350 watt heaters 1.25″ diameter rear material entry. Manufactured 4/89. 990 Lbs. mounted on 41″ centerline v-caster stand.
-
Stock#: 16978
USED PRODUCTION COMPONENTS 35.5″ SHEET DIE
Extrusion die / Nordson sheet die having a 35.5″ slot opening. Upper flexible lip with micro adjustment. Fixed lower lip.3/4″ OD back center feed. 230V/1ph/60Hz last used on flexible PVC. Extremely clean. Includes a stainless steel die cart. S/N 83-7717. Manufactured in 1983.
-
Stock#: 16974
USED CLOEREN 35.5″ HD40 SHEET DIE
Cloeren / Production Components model HD-40 sheet die with a 35.5″ slot opening. Integral flexible upper lip and fixed lower lip. Adjusting bolts are located on 1″ centers. 0.004″ flex adjustment. Coat hanger manifold. Production components S/N 54703-0494. 7/8″ OD back center feed. Last ran flexible PVC. Extremely clean. 230V/1ph/60Hz. 10.5 kW. Weighs 1,074 Lbs. Includes a stainless steel die cart.