Array ( [0] => 75-hp-granulators [1] => feed-paddle-roll-granulators [2] => 75-hp-granulators [3] => feed-paddle-roll-granulators )
  • Stock#: 18714

    USED GRANUTEC TFG2048-100 GRANULATOR W/FEED ROLLS


    One (1) used Granutec model TFG2048-100 granulator. S/N 1297-3109. 20″ x 48″ feed throat. Three (3) knife open rotor with two (2 bed knives. Tangential cutting chamber. Insulated front tray feed hopper with 48″ wide rear feed rolls. 5″ OD smooth air actuated steel feed rolls with 1 HP D/C drive. Granulator set up for a belt drive for 75/100HP motor. 6″ OD airveyor discharge. Motorized actuator for opening the screen cradle. ¼” screen installed. Includes 20″ x 48″ x 24″ top feed extension. Starter and controls not included.

  • Array ( [0] => 75-hp-granulators [1] => feed-paddle-roll-granulators [2] => 75-hp-granulators [3] => feed-paddle-roll-granulators )
  • Stock#: 18718

    USED CUMBERLAND 1456i GRANULATOR W/FEED ROLLS


    One (1) used Cumberland model 1456i granulator. S/N 8400-81004. 14″ x 56″ feed throat. Three (3) knife twin shear rotor with two (2) bed knifes. Rotor is belt driven by a 75 HP motor. 68″ wide in feed pull rolls with 5 HP D/C motor. Feed rolls are pneumatically actuated. Upper and lower feed rolls are poly covered. Pull roll hopper only. No controls are not included.

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 18636

    USED CUMBERLAND 484 GRANULATOR WITH FEED ROLLS


    Cumberland model 484 granulator. S/N 421000-90517. 14″ x 16″ feed throat. 3 knife slant cut rotor, 2 bed knife. 20 HP 460-volt motor. Tray and rear feed roll in-feed. 16″ wide steel feed rolls are powered by a 3/4 HP D/C motor thru a gear reducer. Has 1″ x 14″ “trumpet” in front of the feed rolls. Granulator has Quickdraft internal discharge blower with 6″ OD outlet. Includes starter and controls for the granulator and a D/C variable speed control for the feed rolls.

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 18635

    USED CUMBERLAND 484 GRANULATOR WITH FEED ROLLS


    Cumberland model 484 granulator. S/N 421000-92513. 14″ x 16″ feed throat. 3 knife slant cut rotor, 2 bed knife. 15 HP 460-volt motor. Front feed roll in-feed only. Polynetics 15″ wide steel grooved feed rolls are powered by a 1 HP D/C motor thru a gear reducer. Feed rolls are upgraded with bearings in lieu of brass bushings. Has 1″ x 14″ “trumpet” in front of the feed rolls. Granulator has Quickdraft internal discharge blower with 6″ OD outlet. Includes starter and controls for the granulator and a Bronco II D/C variable speed control for the feed rolls.

  • Array ( [0] => just-arrived [1] => rebuilt-granulators-15-30-hp [2] => feed-paddle-roll-granulators [3] => just-arrived [4] => rebuilt-granulators-15-30-hp [5] => feed-paddle-roll-granulators )
  • Stock#: 18497

    REBUILT AEC WG1256 PADDLE FEED GRANULATOR


    Rebult AEC model WG1256 thermoforming granulator. S/N 509000-10002. 12″ x 56″ feed throat, 5 knife twin shear rotor, 2 bed knife. 30 HP 460V motor. Pneumatic assisted cutting chamber opener. 8″ right hand airveyor discharge, mounted on casters. Includes 10 HP blower with aluminum impeller and sound enclosure. Stand alone original OEM starter / control panel for the granulator and 10 HP interlocked blower. Manufactured in 2010.

  • Array ( [0] => feed-paddle-roll-granulators [1] => under-the-press-granulators [2] => feed-paddle-roll-granulators [3] => under-the-press-granulators )
  • Stock#: 18380

    USED CUMBERLAND 56T PADDLE FEED GRANULATOR


    Cumberland model 56T paddle roll granulator. S/N 209350-08005. 8″ x 56″ feed throat. 3 knife rotor, 2 bed knife. 20 HP 230/460-volt motor. Paddles are powered by a 1 HP A/C motor. 6″ OD airveyor discharge. Mounted on unitized frame with vibration pads. 2008 model year. Starter and controls not included

  • Array ( [0] => 15-30-hp-granulators [1] => as-is-granulators-30-hp [2] => feed-paddle-roll-granulators [3] => 15-30-hp-granulators [4] => as-is-granulators-30-hp [5] => feed-paddle-roll-granulators )
  • Stock#: 18381

    USED TRIA 900/NS-R 12″ X 40″ FEED ROLL GRANULATOR


    One (1) used Tria model 900 NS-R pull roll granulator. S/N 33-2051-7016. 12.5″ x 40″ feed throat (1020mm x 320mm). Five (5) knife open rotor with two (2) bed knives. Rotor is belt driven by a 22 Kw (30 HP). Feed hopper with rear mounted 36″ wide steel / serrated pull rolls. Air actuated feed rolls are powered by a 1 Kw (1.5 HP) A/C motor. 9″ x 19.5″ front material hopper entrance. 12.6 Kw (17 HP) blower discharge with Kongskilde OK160 piping and cyclone with filter bag. Approximate production rate of 400-600 kg/hr (880-1320 lbs/hr). Includes free standing panel with controls. Manufactured in 2004. Very Clean. 480/3/60. Offered “as is”

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 18251

    USED CUMBERLAND 56T GRANULATOR WITH PADDLE ROLLS


    Cumberland model 56T paddle roll granulator. S/N 209350-99008. 8″ x 56″ feed throat. 3 knife rotor, 2 bed knife. 10 HP 230/460-volt motor. Paddles are driven by a D/C motor with a Dayton variable speed drive. Evacuated by a 5 HP blower with 6″ OD outlet and aluminum impeller. All mounted on unitized caster frame. 1999 model year. Complete with starter and controls.

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 17971

    USED CUMBERLAND 484 GRANULATOR WITH FEED ROLLS


    Cumberland model 484 granulator. S/N 521000-85003, 14″ x 16″ feed throat. 3 knife twin shear rotor. 2 bed knives. 15 HP 460v motor. 4″ OD left hand airveyor. Insulated front tray feed hopper with rear mounted 8″ wide knurled steel feed rolls with pneumatic pinch. Tray feed hopper also has a 8″ OD flange mount in-feed opening. Includes starter and controls

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 14292

    USED CUMBERLAND 1628 GRANULATOR WITH FEED ROLLS


    Cumberland model 1628 granulator. S/N 98100-96514. 16″ x 28″ feed throat, 3 knife open rotor, 2 bed knife. 30HP 230/460V motor, insulated tray feed hopper with rear mounted 6″ diameter x 26″ wide Polynetics model RF26 (S/N 6033), steel grooved feed rolls in vertical position with a 7″ x 41″ wide in-feed trumpet tapering to 26″ wide. Feed rolls are powered by a 1-1/2HP 180V DC 1,780 RPM motor direct connected to an Electra 30:1 gearbox, and controlled by a Bronco II variable speed drive. 91.5″ feet per minute maximum roll speed. Enerpac hydraulic operated hopper jack back system 6″ right hand airveyor discharge. Mounted on vibration pads complete with granulator starter and controls.

    2 Available

  • Array ( [0] => as-is-granulators-0-25-hp [1] => feed-paddle-roll-granulators [2] => as-is-granulators-0-25-hp [3] => feed-paddle-roll-granulators )
  • Stock#: 17391

    USED GRANUTEC TFG810-10 FEED ROLL GRANULATOR


    Granutec model TFG810-10 granulator, S/N 0109.4765, 8″ x 10″ feed throat, 3 knife rotor, 2 bed knife, 10 HP 460-volt motor, rear 10″ wide smooth steel feed roll in-feed powered by a 1/2 HP 90-volt D/C motor and variable speed control, 5″ OD right hand airveyor discharge, on casters, complete with starter and controls

  • Array ( [0] => as-is-granulators-30-hp [1] => feed-paddle-roll-granulators [2] => as-is-granulators-30-hp [3] => feed-paddle-roll-granulators )
  • Stock#: 17478

    USED MPG CS-2248 GRANULATOR WITH FEED ROLLS


    MPG model CS2248 granulator S/N F726. 22″ x 48″ feed throat. 9 knife staggered open rotor, 2 bed knife (6 pcs). 150 HP 460-volt 1785 RPM motor. Water cooled cutting chamber. Modified and closed off conveyor style in-feed hopper with rear facing 47″ feed rolls powered by a 2 HP 460-Volt 1745 RPM motor. 8″ OD airveyor discharge. Forklift rail base with vibration pads. No starter or controls included.

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 17466

    USED CUMBERLAND 284 GRANULATOR WITH FEED ROLLS


    Cumberland model 284 granulator, S/N 525525-84012, 10″ x 12″ feed throat, 3 knife open slant cut rotor, 2 bed knife, 7.5 HP 460-volt motor, insulated tray feed hopper with rear facing 8″ wide knurled steel and interlocked feed rolls, feed rolls powered by a 1/2 HP A/C motor and operated by a variable speed drive, 8″ OD left hand airveyor discharge, mounted on casters, complete with granulator starter & controls.

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 17151

    USED CUMBERLAND 284 GRANULATOR WITH FEED ROLLS


    Cumberland model 284 granulator. S/N 325525-7717. 10″ x 12″ feed throat 3 knife open slant cut rotor. Two (2) bed knives. 10HP 230/460V motor. Insulated tray feed hopper with rear mounted 8″ wide x 2.5″ OD knurled steel feed rolls with pneumatic pinch. Mounted in a vertical configuration. Feed rolls are powered by a 3/4HP 90V DC motor. 4″ left hand airveyor discharge. Mounted on casters complete with starter and controls for the granulator and variable speed control on panel.

  • Array ( [0] => as-is-granulators-0-25-hp [1] => feed-paddle-roll-granulators [2] => as-is-granulators-0-25-hp [3] => feed-paddle-roll-granulators )
  • Stock#: 16536

    USED BALL & JEWEL 812 FEED ROLL GRANULATOR


    Ball & Jewel model 812 feed roll granulator, no S/N. 8″ x 12″ feed throat, 3 knife open rotor. 2 bed knife cutting chamber, 25HP 460V rotor motor. Chain and sprocket driven feed rolls. Spring pinch top roll is an 8″ diameter x 12″ wide smooth steel roll. Lower roll is a 6″ diameter 12″ wide knurled steel roll. Rolls are in an off-set position. The rolls are powered by a 3/4HP 1,725 RPM DC motor through a 19:1 gearbox with an output speed of 91 RPM. Blower discharged via a 5HP 3,480 RPM motor with a 4″ OD outlet aluminum blower impeller. Machine is mounted on casters, complete with starter and controls for granulator. DC drive for feed rolls is a constant on configuration with no variable speed control.

    Price: $2,500.00, as is.

  • Array ( [0] => feed-paddle-roll-granulators [1] => feed-paddle-roll-granulators )
  • Stock#: 16280

    USED NELMOR G1215P1 GRANULATOR WITH FEED ROLLS


    Nelmor model G1215P1 granulator. S/N 99K03325. 12″ x 15″ feed throat, 3 knife open rotor, 2 bed knife 15HP 208-230/460V 1,480 RPM motor. Double wall rear top hand feed with front mounted knurled steel feed rolls, pneumatic pinch on rolls. Feed rolls powered by a ½HP (approx.) DC motor and controlled by a Bronco SECO DC variable speed control. Hopper and feed roll assembly has hydraulic jack tilt back assist with a 4″ OD right hand airveyor discharge. Complete with starter and controls for granulator and feed rolls.

  • Array ( [0] => 75-hp-granulators [1] => feed-paddle-roll-granulators [2] => 75-hp-granulators [3] => feed-paddle-roll-granulators )
  • Stock#: 16612

    USED HERBOLD SMS45/160-H5-2 FEED ROLL GRANULATOR


    Herbold model SMS45/160H5, two (2 granulators, S/N 3696 (x2). 23.5″ x 61″ feed throat, belt driven 5 knife open rotor, 2 bed knife, 100HP 230/460V motor. . there is a 11-3/4″ x 30″ parts chute granulator chamber which is opened via a 3HP hydraulic jack back assist. Includes a 1HP material auger discharge assist with an OK160 6″ outlet. Includes two used sets of 20 rotor and 4 bed knives with a knife adjusting fixture. Starter and controls for granulator and feed rolls are not included. Available with or without the feed rolls.

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 12939

    USED CUMBERLAND 284 GRANULATOR WITH FEED ROLLS


    Cumberland model 284 granulator, S/N 325525-83061, 10″ x 12″ feed throat, 3 knife open rotor, 2 bed knife, approximate 2.75″ diameter x 8″ wide grooved knurled & interlocked steel feed rolls. Pneumatic pinched in offset position powered by a 1HP DC motor with variable speed drive mounted on casters complete with starter and controls.

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => used-equipment [3] => feed-paddle-roll-granulators )
  • Stock#: 12690

    USED SPROUT 9 X 11 GRANULATOR WITH FEED ROLLS


    Sprout 9″ x 11″ feed roll granulator, no S/N. 9″ x 11.5″ feed throat, 3 knife open rotor, 1 bed knife cutting chamber, 20HP 230/460V motor. Side feed tray feed hopper with front mounted 3″ x 9″ steel knurled feed rolls powered by an approximately 1/3HP 90V volt DC motor. 7″ OD airveyor discharge, mounted on a frame base, complete with starter and controls for granulator and a variable speed drive for the feed rolls.

  • Array ( [0] => used-equipment [1] => feed-paddle-roll-granulators [2] => recycling [3] => used-equipment [4] => feed-paddle-roll-granulators [5] => recycling )
  • Stock#: 12541

    USED CUMBERLAND MODEL 18 x 37 GRANULATOR WITH FEED ROLLS


    Cumberland model 1837-5KN granulator. S/N 50510-84013. 18″ x 37″ feed throat, 5 knife steep angle step adjustable rotor knives (10 segments), 2 bed knife. Designed for film granulation. Belt driven by a 100 HP 460V only 1,780 RPM motor. Gravity discharge 6″ diameter x 37″ wide knurled and grooved offset position feed roll infeed with pneumatic pinch feed roll in-feed trumpet. Feed rolls are chain and sprocket driven by a 7.5HP 1,750/1,930 RPM continuous duty DC motor through a reliance 2.76:1 gearbox. All mounted on a leg base with swing out chamber door on down stroke side. Starter and controls are not included.