Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18201

    USED CUMBERLAND #6 PELLETIZER


    Cumberland size 6 pelletizer. S/N 26111-6446. 12 knife bolt on rotor. One bed knife. Powered by a 3 HP 208/220/440-volt motor thru a US Motors mechanical variable speed drive. Mounted on casters. Includes starter with start / stop buttons and disconnect.

    Video Link below

    https://1drv.ms/v/s!Ahk76-e5leU7jw9Ka4DYsh_4–XH



  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18106

    USED CONAIR 304 4″ PELLETIZER


    Used Conair model 304 4″ wide strand pelletizer. S/N 6-010880. Powered by a 2 HP 230-volt motor. Equipped with a 24 knife helical rotor and controls

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18164

    USED SCHEER BAY SGS-100E 4″ PELLETIZER


    Used Scheer Bay model SGS-100E 4″pelletizer. S/N SE100505. Has a 36 knife helical rotor. 460 volt

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18158

    USED CONAIR 306DU 6″ PELLETIZER


    Used 6″ Conair Model 306DU strand pelletizer. S/N ACG-01487. Has a 20 knife helical rotor and dual motor design with individual variable speed motors for the pull rolls and helical rotor. 230 volt operation


  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18157

    USED CUMBERLAND 8″ PELLETIZER


    Used 8″ Cumberland “Quietizer” Pelletizer. Has 36 knife helical rotor. Driven by a 10 HP DC motor, 230/460 3 phase 60 hertz.

  • Array ( [0] => lab-testing-equipment [1] => pelletizers [2] => lab-testing-equipment [3] => pelletizers )
  • Stock#: 18126

    USED ACCRAPAK SYSTEMS LAB PELLETIZER


    One (1) used Accrapak Systems model 750/1B laboratory strand pelletizer. 1″ entrance. 24 knife solid helical rotor. 1 HP drive motor. Includes 4″ air knife. S/N 5288-9-95

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18117

    USED CONAIR / JETRO 304 36 KNIFE PELLETIZER


    One (1) used Conair Jetro Model 304 Strand Pelletizer. S/N 6-040581. 4″ wide 36 knife helical rotor driven by a 2 HP 230-volt single phase motor. 10 amps maximum load. Includes drive and controls. Missing rubber roll

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18118

    USED CONAIR 304 20 KNIFE PELLETIZER


    One (1) Used Conair Jetro Model 304 Strand Pelletizer. S/N 98778. 4″ wide 20 knife helical rotor, driven by 2 HP D/C motor. 10 amps maximum load, includes drive and controls. 230/1/60 input power. Missing rotor.

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18132

    USED CONAIR 304 PELLETIZER


    One (1) used Conair model 304 strand pelletizer. S/N 6-041185. 4″ wide entrance and with loose 8 knife solid helical rotor. 2 HP D/C motor with SCR control. 230/1/60 operation

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18089

    USED CONAIR 8″ 32 KNIFE PELLETIZER


    One (1) used Conair strand pelletizer having an 8″ entrance. 32 knife solid helical rotor. 15 HP Baldor Super E motor with inverter. 460/3/60 operation

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18116

    USED CUMBERLAND 8″ 48 KNIFE PELLETIZER


    One (1) Used 8″ Cumberland “Quietizer” pelletizer. S/N 264550-940006. Rotor is driven by a 15 HP A/C motor with inverter. 3 HP A/C pull roll motor. Has (48) knife solid helical rotor. Air actuated nip rolls. Sound enclosed. Caster mounted. Manufactured in 1994

  • Array ( [0] => just-arrived [1] => extruders-3-5-10 [2] => pelletizers [3] => pelletizing-lines [4] => just-arrived [5] => extruders-3-5-10 [6] => pelletizers [7] => pelletizing-lines )
  • Stock#: 18180

    USED PRODEX 4.5″ EXTRUDER / PELLETIZING LINE


    One (1) used pelletizing line with Prodex 4.5″ 32:1 L/D extruder having an electrically heated, water cooled (closed loop), and side vented barrel. The gearbox is a Lufkin change gear gearbox and driven in a tuck under manner by a 300 HP A/C motor with Yaskawa inverter. Includes stand-alone cooling system for the gearbox. Over-sized on center oblong feed throat with water cooling and volumetric screw feeder. Free-standing temperature control panel has ten (10) zones of temperature controls. Inverter is free standing and mounted in its own enclosure. Mounted on the extruder discharge is a hydraulic slide plate screen changer having two (2) nominal 4.5″ diameter breakers with hydraulic power pack, stand, and strand die. Downstream includes an 11″ Cumberland “Quietizer” pelletizer with solid helical rotor. Powered by a 25 HP A/C motor and Yaskawa model V1000 inverter. Pelletizer feeds 10″ x 72″ Witte two deck screener. Offered less extruder screw.

  • Array ( [0] => just-arrived [1] => pelletizers [2] => pelletizing-lines [3] => just-arrived [4] => pelletizers [5] => pelletizing-lines )
  • Stock#: 18007

    USED PTI WATER RING PELLETIZING LINE


    One (1) used 1999 PTI pelletizing line with model TS4500 4.5″ 30:1 L/D extruder having an electrically heated, water cooled (closed loop), and side vented barrel at a nominal 42″ center-line height. The gearbox is a Flender model SZNE250 having a reduction ratio of 13.88:1 and has a service rating of 200 HP and a catalogue rating of 325 HP. The gearbox is belt driven in a wraparound manner by a 200 HP D/C motor with Safetronics SCR control. Over-sized on center oblong feed throat with water cooling. Free-standing temperature control panel has ten (10) zones of temperature controls. SCR is mounted inside the control panel. 480/3/60 400 amps. S/N 1832. Mounted on the extruder discharge is a model HSC-45 hydraulic slide plate screen changer having two (2) nominal 4.5” diameter breaker plates with oversized 5 HP hydraulic power pack. S/N H45-204. Downstream is a PTI model CPF1000S water ring pelletizing system with 3 HP cutter head, die, sluiceway, water system, Gala model 8.1BF spin dryer and control panel. S/N 2780. 460/3/60 30 amps.

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 18133

    USED SCHEER BAY SGS-50E PELLETIZER


    One (1) used Scheer Model SGS-50-E strand pelletizer. S/N SE5-0707. Nominal 2″ wide entrance. Has 20 knife carbide inlay helical style rotor driven by an A/C motor with Reliance variable speed controller. Mounted on caster base. 460-volts. 4.5 FLA

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 17922

    USED SCHEER SGS-50EL 2″ 20 KNIFE PELLETIZER


    One (1) used 2″ Scheer Model SGS-50-EL strand pelletizer. S/N 10050017. Nominal 2″ wide entrance. Has 20 knife carbide inlay helical style rotor driven by an A/C motor with variable speed controller. Mounted on caster base. 460-volts. Manufactured in 2013. Extremely clean.

  • Array ( [0] => just-arrived [1] => pelletizers [2] => just-arrived [3] => pelletizers )
  • Stock#: 17908

    USED GALA 5MUP UNDERWATER PELLETIZING SYSTEM


    One (1) used Gala model 5MUP underwater pelletizing system. Includes 2 HP cutter with four (4) blade hub, three (3) spare dies, 40 GPM TWS-40 water system with heater, pump, heater exchanger, 5 HP model 8.2 BF dryer, and non-OEM custom control panel. S/N 8801458

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 17625

    USED CDL UNDERWATER PELLETIZING SYSTEM


    One (1) used incomplete CDL model UWP36620 underwater pelletizing system. Includes 20 HP cutter less cutting hub, 48 hole electrically heated die, and water tempering system including pump, reservoir, and heated exchanger. S/N DB06. Job number J1871

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 17732

    USED CUMBERLAND 6″ PELLETIZER


    Used 6″ Cumberland Quietizer pelletizer. S/N 3260503-85002. Driven by approximately a 5 HP D/C motor with SCR. Has sixteen (16) knife rotor with removable blades. Air actuated nip rolls. Sound enclosed. Caster mounted.

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 17692

    USED SCHEER BAY SGS100-E PELLETIZER


    Used 4″ wide Scheer Bay pelletizer Model SGS100-E. S/N SE10CC-9801, 460 volt A/C input, 3 phase, 60 hertz, 14.2 amps. Has 32 knife carbide inlay helical style rotor driven by an AC Tech variable speed controller. Mounted on caster base.

  • Array ( [0] => pelletizers [1] => pelletizers )
  • Stock#: 12960

    USED CUMBERLAND 20″ PELLETIZER


    Cumberland model 20 pelletizer, S/N None. 36 knife helical rotor, Hypalon rolls, 15HP 460V motor arranged through a manual variable drive, no controls.