-
Stock#: 18478
USED HARTIG 2.5″ PELLETIZING LINE
One (1) used 2.5” pelletizing line including the following:
A. One 2.5″ Hartig extruder with a 24:1 L/D four (4) zone electrically heated, air cooled, and non-vented barrel at approximately a 42″ center line height. Serial number BE-836. 3″ round feed entrance. Koellmann gearbox has a reduction ratio of 13.95:1 and is rated at 108 HP at a service factor of 1.0. Gearbox is belt driven by a 50 HP GE D/C motor with Safetronics model DC-6 SCR control. Free standing temperature control panel has seven (7) zones of Eurotherm 3208 digital controllers. Water cooled screw with rotary union. Manufactured 1/21/1993. Very clean. 460/3/60 input power.
B. Mounted on the discharge of the extruder is a six hole electrically heated strand die with downward orientation.
C. Nominal 6’ long Emery stainless steel water bath measuring 14” wide x 8” deep with strand guides. Includes 54” x 34” x 24” stainless reservoir, Alpha Laval plate and frame heat exchanger with ½ hp pump and 1 ½ hp Liberty pump for the water bath.
D. Berlyn model HV-2 air stripper with nominal 10” slot opening, 2 HP blower, starter and disconnect. 460/3/60.
E. 6” Cumberland “Quietizer” pelletizer having a sixteen (16) knife rotor with removable blades. S/N 326050-B-92016. Factory sound suppression enclosed. Air actuated top rubber roll. Rotor and pull rolls are V-belt driven by a 7.5 HP inverter duty A/C motor with Yaskawa V1000 inverter with remote keypad. Manufactured in 1992. Exceptional condition.
All equipment is extremely clean and recently pulled from service. Great small line for reclaiming captive scrap.
-
Stock#: 18007
USED PTI WATER RING PELLETIZING LINE
One (1) used 1999 PTI pelletizing line with model TS4500 4.5″ 30:1 L/D extruder having an electrically heated, water cooled (closed loop), and side vented barrel at a nominal 42″ center-line height. The gearbox is a Flender model SZNE250 having a reduction ratio of 13.88:1 and has a service rating of 200 HP and a catalogue rating of 325 HP. The gearbox is belt driven in a wraparound manner by a 200 HP D/C motor with Safetronics SCR control. Over-sized on center oblong feed throat with water cooling. Free-standing temperature control panel has ten (10) zones of temperature controls. SCR is mounted inside the control panel. 480/3/60 400 amps. S/N 1832. Mounted on the extruder discharge is a model HSC-45 hydraulic slide plate screen changer having two (2) nominal 4.5” diameter breaker plates with oversized 5 HP hydraulic power pack. S/N H45-204. Downstream is a PTI model CPF1000S water ring pelletizing system with 3 HP cutter head, die, sluiceway, water system, Gala model 8.1BF spin dryer and control panel. S/N 2780. 460/3/60 30 amps.
-
Stock#: 17001
USED AUTOMATIK / GALA MODEL SPHERO 220 UNDERWATER PELLETIZING SYSTEM
Automatik / Gala model SPHERO 220 underwater pelletizing system. Unit is rated at up to 22,000 pounds per hour. Machine serial number 1018144-SH-117. Manufactured in 2010. 460V/3ph/60Hz operation.
The system consists of the following components:
A) Hydraulically actuated start up value with an 11 kW hydraulic pump.
B) Liquid heated die plate with a Sterlco model M2B6017-L, 80 kW oil heater.
C) A 60HP, 36 knife cutter head with a pneumatically adjustable knife shaft.
D) A cutting chamber with a tangential water supply and pellet drain.
E) Movitech model VSF90/4-2B water tempering system with a FUNKE model plate type heat exchanger.
F) A 7.5HP spin dryer with an agglomerate catcher and a 1.5HP blower motor (missing the motor).
G) A free-standing control panel.
H) A support structure for the cutter, cutting chamber, hydraulic pump, hydraulic vale, and operator controls.
Last used on EPS micro beads.
-
Stock#: 17002
USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM
One (1) used Automatik / Gala model Sphero 220.1 underwater pelletizing system. Unit is rated for up to 22,000 pounds per hour. Order number 1019020. Machine number SH-204. Manufactured in 2013. 460V/3ph/60Hz operation.
The system consists of the following components:
A) Hydraulically actuated start up value with 11 kW hydraulic pump.
B) Liquid heated die plate with Sterlco model M2B6017-L 100 kW oil heater.
C) A 60HP 36 knife cutter head with a pneumatically adjustable knife shaft.
D) A cutting chamber with tangential water supply and pellet drain.
E) A Movitec model VSF 90/4-2B water tempering system with a FUNKE plate type heat exchanger
F) A 7.5HP spin dryer with an agglomerate catcher and a 1.5HP blower.
G) A free standing control panel. H) A support structure for the cutter cutting chamber, hydraulic pump, hydraulic vale, and operator controls.
Last used on EPS micro beads.
-
Stock#: 17003
USED AUTOMATIK / GALA MODEL SPHERO 220.1 UNDERWATER PELLETIZING SYSTEM
Automatik / Gala model Sphero 220.1 underwater pelletizing system. Unit is rated up to 22,000 pounds per hour. Order number 1019020. Machine number SH-205. Manufactured in 2013. 460V/3ph/60Hz.
The system consists of the following components:
A) A hydraulically actuated start up value with 11 kW hydraulic pump.
B) A liquid heated die plate with a Sterlco model M2B6017-L 100 kW oil heater.
C) A 60HP 36 knife cutter head with a pneumatically adjustable knife shaft
D) A cutting chamber with a tangential water supply and pellet drain.
E) A Movitec model VSF 90/4-2B water tempering system with a FUNKE type plate heat exchanger.
F) A 7.5HP spin dryer with an agglomerate catcher and a 1.5HP blower.
G) A free standing control panel.
H) A support structure for cutter, cutting chamber, hydraulic pump, hydraulic vale, and operator controls.
Last used on EPS microbeads.
-
Stock#: 18180
USED PRODEX 4.5″ EXTRUDER / PELLETIZING LINE
One (1) used pelletizing line with Prodex 4.5″ 32:1 L/D extruder having an electrically heated, water cooled (closed loop), and side vented barrel. The gearbox is a Lufkin change gear gearbox and driven in a tuck under manner by a 300 HP A/C motor with Yaskawa inverter. Includes stand-alone cooling system for the gearbox. Over-sized on center oblong feed throat with water cooling and volumetric screw feeder. Free-standing temperature control panel has ten (10) zones of temperature controls. Inverter is free standing and mounted in its own enclosure. Mounted on the extruder discharge is a hydraulic slide plate screen changer having two (2) nominal 4.5″ diameter breakers with hydraulic power pack, stand, and strand die. Downstream includes an 11″ Cumberland “Quietizer” pelletizer with solid helical rotor. Powered by a 25 HP A/C motor and Yaskawa model V1000 inverter. Pelletizer feeds 10″ x 72″ Witte two deck screener. Offered less extruder screw.