Array ( [0] => temperature-control [1] => temperature-control )
  • Stock#: 18742

    USED STERLCO M2B9016-J1 OIL TEMPERATURE CONTROL


    One used Sterlco model M2B9016-J1 single zone oil media temperature control unit. S/N 30F5659. 36 KW (2 x 18 kw) oil heating with cooling provision. 3 HP pump. 100 PSI maximum. 460/3/60. 49 FLA. Mounted on casters.

  • Array ( [0] => pipe-profile-cutters [1] => pipe-profile-cutters )
  • Stock#: 18741

    USED VERSA S1ACT-C22 CUTTER / PULLER


    One (1) used Versa model S1ACT-C22 profile puller / cutter combination. S/N SO019661. Belt puller has 2″ wide belts with 11″ of contact length. Servo driven puller and cutter. Cutter can handle up to a 1″ OD. Set up for right to left operation. Height adjustable. Manufactured 04/2019. Limited use. Excellent condition.

  • Array ( [0] => injection-molding [1] => miscellaneous [2] => injection-molding [3] => miscellaneous )
  • Stock#: 18740

    USED SAVAGE 5 TON PLATTEN PRESS


    One (1) used Savage 5 ton dual-acting 4 post hydraulic compression molding press. S/N 2001. Having two (2) 60″ x 32″ electrically heated platens. 54″ left to right between the posts. 8″ of stroke on each platen. 7″ clearance between platens. Manufactured in 1995. Allen Bradley Panelview 600 microprocessor control. With manual.

  • Array ( [0] => extrusion-melt-pumps [1] => extrusion-melt-pumps )
  • Stock#: 18672

    USED WELEX / MAAG 20 HP MELT PUMP


    Welex / Maag model 56/56 20 HP melt pump with drive

  • Array ( [0] => just-arrived [1] => pelletizing-lines [2] => just-arrived [3] => pelletizing-lines )
  • Stock#: 18739

    USED 6″ DAVIS STANDARD / XALOY PELLETIZING LINE


    Used Davis Standard / Xaloy 6″ pelletizing line consisting of:

    One (1) Davis Standard 6” model 60IN60TPTH extruder having a 34:1 L/D ratio barrel with a seven (7) zone electrically, heated, water cooled (closed loop), and vented barrel at a 42” centerline. Part Number 0022356-1-1.  8” x 12” on center feed throat. Oversized (8”) Gearbox is direct driven in a wraparound manner by a 500 HP Reliance Super RPM 1150/1680 RPM D/C motor with Siemens Simoreg Microprocessor SCR control mounted in a stand-alone enclosure. Gearbox has a reduction ratio of 11.304:1 and is rated at 1050 HP at a service factor of 1.5. Liquid cooling system with heat exchanger for gearbox protection. Stand-alone control panel with sixteen (16) zones of Barber Coleman model 2408 digital controllers. Manufactured 9/2011. Gearbox completely rebuilt by Texas Extrusion Services 4/2022. 460/3/60. Drive 794 amps. Temp panel 400 amps. Reportedly barrier screw installed.

    Xaloy model EH-80SH hydraulic slide plate screen changer having two (2) nominal 8″ diameter breaker plates. Serial number EH80-180  Mounted on a stand. With 3 hp hydraulic power pack with oversize accumulator.

    Xaloy model WRP-35S Pelletizer with 3 HP Cutting Head with stand, water reservoir with two (2) 1.5 HP water pumps, 7.5 HP slurry pump, 5 HP Spin Dryer, control panel and caster mounted pellet accumulation hopper. Serial number VB1057

  • Array ( [0] => 75-hp-granulators [1] => 75-hp-granulators )
  • Stock#: 18508

    USED ROTOGRAN WO2224 GRANULATOR


    Rotogran model WO2224 granulator. S/N H22241208205WO. 22″ x 24″ feed throat. 5 knife (10 pcs) open rotor, 2 bed knife. Dual Fly-wheels. Tangential cutting chamber. 75 HP 460-volt motor. 8″ OD right hand airveyor discharge. Non-OEM tray or conveyor in-feed hopper. Vibration pad base. Includes starter and controls. Manufactured in 2012.

  • Array ( [0] => extrusion-miscellaneous [1] => extrusion-miscellaneous )
  • Stock#: 18722

    USED CONAIR EXTRUDER SIDE FEEDER


    One (1) used Conair model BFO at the throat color feeder. Includes receiving hopper with lid and Extruder Tracking Feeder control. Serial number 116071. ¾” screw. 115/1/50. 5 amps.

  • Array ( [0] => vacuum-loaders [1] => vacuum-loaders )
  • Stock#: 18720

    USED CONAIR DB VACUUM LOADER


    Conair model DB vacuum loader. S/N 401375. 1.75″ OD line. 115-volts single phase 60hz 8 Amps. Includes controller.

    2 Available

  • Array ( [0] => extruders-twin-screw [1] => extruders-twin-screw )
  • Stock#: 18512

    USED CINCINNATI 112mm TWIN SCREW EXTRUDER


    Used Cincinnati model Argos 112P-65-20-1150-UL 112mm parallel counter rotating twin screw plastic extruder. S/N 2041843/010. Screw length approximately 3020mm long x 112mm diameter screw, L/D ratio of 27:1. Barrel is electrically heated and air cooled in 4 zones with air blowers air blowers with approximately .45 kw motors. Unit is driven by 65 kw, 420-volt, 2000 RPM 3 phase 50/60 hz motor through gearbox with 96:188 reduction ration. Unit has top entry Plasticolor 2200 vibratory feeder with horizontal screw feeder driven by 1.1 kw motor. Unit includes local controls. Manufactured in 2002.

  • Array ( [0] => extruders-twin-screw [1] => extruders-twin-screw )
  • Stock#: 18511

    USED CINCINNATI 80mm TWIN SCREW EXTRUDER


    Used Cincinnati model CMT80L-APC 80mm conical counter rotating twin screw plastic extruder. S/N 2040985/010. Screw length approximately 1,665mm long x 80mm diameter at the discharge. Has adapter plate that reduces the barrel exit down to 65mm diameter. Barrel is electrically heated and air cooled in 4 zones with air blowers with .45 kw motors. Unit is driven by 49 kw, 415-volt, 50hz main motor and gearbox with an output 25.5 RPM screw speed. Unit has top entry Plasticolor 2200 vibratory feeder with horizontal screw feeder driven by approximately .55 kw motor. Unit has local controls. Manufactured in 2002

  • Array ( [0] => extruders-twin-screw [1] => extruders-twin-screw )
  • Stock#: 18510

    USED BATTENFELD CM55 TWIN SCREW EXTRUDER


    Used Battenfeld-Cincinnati model CM55 counter rotating twin screw extruder. S/N 2804784/010. Conical screw design. Barrel is electrically heated and air cooled in three zones with air blowers with .20 kw motors. Unit is driven by 37 to 49.5 kw, 350 to 493 volt, 50.8 to 74.2 hz, 1500 to 2200 RPM electric motor with gearbox. Unit has top entry Plasticolor 2500 vibratory feeder with horizontal screw feeder driven by a .55 kw motor. Unit includes touchscreen controls.  Located in UK

  • Array ( [0] => vacuum-pumps [1] => vacuum-pumps )
  • Stock#: 18719

    USED CONAIR 25 HP VACUUM PUMP


    Conair vacuum pump. Powered by a 25 HP 208-230/460-volt motor. 29.8 maximum amps. 4″ NPT line size with in-line air filter. Gardner Denver GAFMDPA0177 blower. Mounted on a low rise base. Starter and controls not included.

  • Array ( [0] => extrusion-screen-changers [1] => extrusion-screen-changers )
  • Stock#: 18509

    USED MAAG 4″ CONTINUOUS SCREEN CHANGER WITH MELT PUMP


    Maag 4″ Continuous Screen Changer with Melt Pump. S/N 50125578-20. Consists of One (1) used Maag model CSC-096 screen changer having two (2) nominal 2.3.8″ breaker plates. Rated at 300-500 Kgs/hr (660-1100 pounds/hour). On caster mounted cart. With 3 HP hydraulic pump and controls. Downstream of the screen changer is a Maag model Extrex 45/45 melt pump. S/N 5012SS78-10. Unit is driven by a 5 HP inverter duty AC motor. Gear pump rated from 80-700 pounds an hour at 245 degrees C. Gear pump is also mounted on a cart.

  • Array ( [0] => vacuum-loaders [1] => vacuum-loaders )
  • Stock#: 18723

    USED CONAIR AL VACUUM LOADER


    Conair model AL vacuum loader. S/N 241553. 115-volts single phase 60 hz 8 FLA. Includes controller.

  • Array ( [0] => extruders-34-3 [1] => extruders-34-3 )
  • Stock#: 18504

    USED PTI 2.5″ 32:1 L/D 50 HP EXTRUDER


    One (1) used PTI model 2500 2.5″ extruder. S/N 3907/00446. 32:1 L/D barrel having a five (5) zone electrically heated, air cooled, and non-vented barrel at an approximate 42″ center line height. Unit has a Koellmann model Unex 14.1 gearbox having a reduction ratio of 17.533:1 and is direct driven out the back of the gearbox by a 50 HP Reliance A/C motor with Reliance GV 3000/SE inverter. 3.5″ x 4″ feed throat entrance. Caster mounted. Offered less extruder screw. 460/3/60. Manufactured 03/2004

  • Array ( [0] => vacuum-receivers [1] => vacuum-receivers )
  • Stock#: 18734

    USED NOVATEC 2 CUBIC FOOT VACUUM RECEIVER


    Novatec model 04338-20 vacuum receiver. S/N 12-784. Manufactured 11/99. Approximate 2 cubic foot capacity. 16″ OD x 22″ chamber plus bottom taper. Includes flapper valve. 2″ OD line size.

    2 Available

  • Array ( [0] => piping-venturi [1] => piping-venturi )
  • Stock#: 18736

    USED LOT OF 8″ OD JACOB’S PIPE


    Used lot of approximately 87 feet Jacob’s 8″ pipe. Consists of 13 pcs of 2 meter, 2 pcs of 90 bends, one 1 meter, one telescope, and 13 clamps.

  • Array ( [0] => conveyors [1] => conveyors )
  • Stock#: 18729

    USED HYTROL 15′ X 18″ INCLINE CONVEYOR


    Hytrol model TA incline conveyor. S/N 239858. 15 feet long x 18″ wide rough texture belt. Mounted on casters. 36″ discharge height. Powered by a 1/2 HP 230/460-volt motor

  • Array ( [0] => just-arrived [1] => as-is-granulators-30-hp [2] => just-arrived [3] => as-is-granulators-30-hp )
  • Stock#: 18733

    USED WEIMA LM600/1000 GRANULATOR


    Weima (Neue Herbold) model LM600/1000S5-2 granulator. S/N 63053-2. 5 knife rotor (10 pcs), 2 bed knives. 24″ x 39″ cutting chamber with a 24″ diameter cutting circle. V-belt driven rotor by a 66kw (90 HP) 460-volt 1780 RPM motor. Conveyor style in-feed hopper with an in-feed height of 100″. 8″ OD airveyor discharge. 3/8″ holes screen installed. Original OEM standalone control panel with A/B PLC controller. 85″ x 82″ granulator foot-print. Includes manual, granulator to control panel cable, spare set of used knives, and knife installation / adjustment fixture. All manufactured in 2019 and in excellent running condition.

  • Array ( [0] => screeners-sifters [1] => screeners-sifters )
  • Stock#: 18697

    USED SWECO 60″ FOUR DECK SCREENER


    Used 60″ Sweco model XS60C8108 carbon steel screener. S/N 68808-A594. Four decks, three separations. Driven by a 2.5 HP 230-volt motor.